Search Documents

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By R. Cotton

"1. INTRODUCTIONTo say that the environment will be a dominant issue in the 1990' s is an understatement. A world-wide ""green revolution"" is taking place not only with the general public and politicians, but in the boardrooms and plant facilities of corporations around the world. There is probably not a plant manager who has not been requested by his corporation to assist in some way on environmental issues by providing advice and strategy, by dealing with customer or community concerns, by considering environmental matters in transactions, by developing new environmental compliance policies and requirements, and so on.There are, in the author's view, three main challenges for the mining industry in the environmental area in the 1990's. This paper will discuss each in turn. The first challenge is the concept of ""sustainable development"". Whatever the meaning of this much-debated phrase, we are rapidly moving beyond the buzzword, and into the specifics. It will clearly impact on the way we manage our companies, our communities and our personal lives.The second is the challenge of personal liability; particularly for officers, directors, supervisors and managers of the corporation. For example, in Ontario today, a good percentage of prosecutions for pollution offences are against individuals, usually managers and supervisors, in addition to the prosecutions against the corporation itself for the same offence. In all likelihood, prosecutions will increase in number and will increasingly be directed at individuals. A corporate president has already served a jail term for contempt of court related to his corporation's breach of a court order related to sewer by-law offences. Although the case is on appeal, another president has become the first officer in Canada to be sentenced to jail for violation of an environmental protection statute. Other corporate officers and directors have recently been charged with breach of their duty under Ontario's Environmental Protection Act."

Jan 1, 1991

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916,1 and an investigation of Illinois coal-washing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coal. OBJECTS OF THE INVESTIGATION The present investigation was limited to a study of screening as applied in preparing mineral products with the expectation of obtaining more comprehensive information on screening machinery.

Jan 1, 1925

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

By L. W. Higley

Electrowinning metals from solutions leached from low-grade ores is becoming an increasingly important extraction method as the metal industry turns to pollution-free recovery processes. Lead-alloy anodes are used industrially in the electrolytic recovery of zinc and copper. However, associated with the use of these anodes are the inherent problems of stability and lead contamination of the cathode. In an effort to eliminate these problems, the Bureau of Mines has developed a relatively inexpensive lead dioxide anode for electrowinning metals from strong acid solutions. The anode was prepared by depositing Pb02 directly on a titanium blank in a strong HN03-Pb(N03)2 solution at 2.15 to 6.45 A/dm2 and 60° C. This anode was tested in zinc and copper electrowinning cells containing 200 gpl H2S04 and 35 to 100 gpl metal ions at the current density of 3.23 to 6.45 A/dm2. Contamination of the cathode by lead was =0.005 pet. A 30-day test at 6.45 to 12.90 A/dm2 in an electrolyte containing 200 gpl H2S04 and no metal ions resulted in a slight change in surface morphology of the Pb02 anode but no measurable change in anode weight or dimensions.

Jan 1, 1976

By P. T. Slatter

The efficient and accurate design of pipe and pumping plant for non-Newtonian mineral slurries remains a problem. The objective of this paper is to present the development of the Balanced Beam Tube Viscometer (BBTV), an instrument which could facilitate more accurate design for these slurries. The background of rotational and tube viscometry is reviewed and the fundamental principles and inherent advantages of the BBTV are given. The design, data acquisition and processing techniques are introduced and results showing the reliability of the new instrument are presented and discussed. It is concluded that the BBTV is a reliable and versatile instrument for both routine analyses and research work, and has the potential to provide data for the refinement of the design procedure for mineral slurry pipe and plant design.

Jan 1, 1998

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By P G. Rutherford, A W. McOnie

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralised and is unconformably overlain by two post-mineral units, the lacustrine Waitekauri beds and Omahine Subgroup andesite.   Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralising events. Faulting was coeval with the mineralization and directly controlled the development, localisation, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralised veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralising events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the orebody.

Jan 1, 1995

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral'iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,' while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Hu Harries

WE RECENTLY completed a study for a client, who is an applicant to export gas from the Province of Alberta, on the effects of gas export on Alberta's economy. This study was part of the client's application ?before the Conservation Board, and, no doubt, some of you are familiar with it. Submissions by other applicants in earlier hearings before the Board and before the Royal Commission on Energy, as well as claims made by parties opposing export, have also brought forward a number of other opmwns regarding possible economic effects. Ali of these studies have been on a piecemeal basis. They have dealt with particular aspects of particular applications, and only indirectly and by inference with the overall question of gas ex-port. We have prepared this paper to review the overall picture and ex-amine, as far as time permits, all sides of the question. While the paper is entitled Economic Effects of Gas Export on Alberta, we felt that the area considered should in-elude northeastern British Columbia, not only because Westcoast, the first major gas export project, is essentially a northeastern B. C. project, but because this area has historically been, from the point of view of economic, if not of political, geography, part of Alberta. In this paper, when we talk of export, we mean export from the Province or, in this case, from Alberta plus northeastern B. C. Sales to other parts of Canada have exactly the same effect on the economy of this area as l1ave sales to the United States, provided, of course, they are made on equal terms.

Jan 1, 1958

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984

By R. Ward Stahl

Fire is still a scourge of the mining industry, although many precautionary measures have been and are being taken to reduce the incidence of fires and to combat them. Generally, the success of fire extinguishment is directly proportional to the speed of attack, and the speed of attack in turn is dependent upon the availability of materials and trained personnel. Preparations for firefighting are frequently neglected because they are considered emergency needs and do not contribute directly to coal production. Fire incites panic--a fact often overlooked--but such chaos can be minimized by training people in the use of equipment and procedures. Heat, smoke, and fumes hamper the approach to a fire; however, a relatively new technique of attacking fires with high-expansion foam may well contribute greatly to firefighting. The foam is transported to a fire and used at a considerable distance, thus permitting the firefighters to work more safely.

Jan 1, 1962

By S. C. Langvik

The presentation named 'Dewatering of fines by Rotary Vacuum Disc Filters' has an opening why the filtration process is important to the Iron Ore Industry. It goes on to describe the various types of dewatering machines which have been used in this industry in the last 30-40 years, and where the vacuum disc filters now dominates. It presents also the most important design changes which have been made during this period to enhance performance. Further are discussed the principles of filtration and the factors and parameters which influence performance and operating costs. As a closing is presented today's ideas and thoughts about what can be foreseen of design modifications and improvements in disc filter design in the coming ten years.

Jan 1, 2001

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By Paul. D. Merica

I LIKE to look upon the award this year also as a recognition of the importance of metallic materials of construction to the engineer and of the active progress which I believe is continually being made in almost all branches of that field today. It has been said that metals are the material backbone of industry and technology. Well in that case, I suppose we metallurgists are industry's bonesetters. And it is possibly not inappropriate that we should occasionally give some atten¬tion to those bony structures of our industrial activities upon which engineers in other fields hang their manifold and striking creations. What is going on in the field of metals development? Well, in the first

Jan 1, 1938

By J Lea, P Hatherly, J L. Edwards

Coal exploration has traditionally involved the acquisition of data to enable a resource to be quantified and qualified to the extent that its economic potential can be determined. This process commonly relied on: drilling to determine the depth and thickness of coal seams, broad characterisation of the overburden and interburden, and to provide cores for coal quality analyses; basic wireline logging to cross-check the depth and thickness of coal seams and provide some indication of rock mass strength; and basic surface geophysics and remote sensing to identify major geological structures. In recent years, the adoption of the JORC Code as a basis for the reporting of resources and reserves has placed a greater emphasis on the need for detailed, reproducible data sets that not only satisfy the traditional requirements of mine planners, but also satisfy the governance requirements of corporate and financial institutions. Similarly, the development of sophisticated numerical modelling techniques for use in both open cut and underground mine design, has seen a greater demand for precise geotechnical data, in situ stress characterisation and hydrological information as routine input to the design process. These requirements, coupled with the prevailing trend toward high capital, relatively inflexible mining techniques less tolerant of geological surprises, and the need for consideration of environmental issues such as groundwater impacts and surface subsidence, requires that modern exploration programs be multifaceted, and designed to commence capturing data relevant to ædownstream issuesÆ even during the initial phases of exploration planning.

Jan 1, 2009

By Kenneth Gavin

The accurate prediction of the shaft capacity of drives piles in sand continues to present problems for foundation designers. Research in this field has been carried out for many years and has yielded a wide range of design approaches -some of which have been shown by recent experimental work to be based on questionable assumptions. This Paper reviews some of the current popular design methods for piles in sand in the context of recent information obtained from high quality field tests conducted by institutions such as Imperial College London. A database of driven piles in cohesionless soils has been compiled from well documented (and reliable) case histories that have been reported in the literature. The measured shaft capacities of the piles in this database are compared with predictions made by the various methods and an assessment is made of the predictive performance and reliability of each method

Jan 1, 1996