Search Documents

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By Fernando Bermejo

El presente texto describe la implementación del método Flash - Flotation para el proceso de optimización de plantas concentradoras polimetálicas en la Compañía minera Raura donde se tienen diferentes gravedades especificas por cada especie mineralógica. Su aplicación comprende la fase de investigación (año 89), modificaciones (año 2002) durante la etapa de escalamiento industrial y la optimización (año 2004) de estos equipos en la empresa, los cuales no han requerido de una gran inversión. Asimismo, los beneficios de operar con la celda SK-80 y SK-240 directamente a la descarga de los molinos primarios, permite optimizar el control metalúrgico. En este sentido, la idea de separar el plomo tan pronto lo permita el sistema, es la forma correcta de optimizar la metalurgia de este en la Compañía minera Raura.

Sep 12, 2005

It's long been suspected that there has been an increase in the incidence of premature failure of rock bolts in underground coal mines over the past ten years. As far back as 2002 a study found a possible contributor to such premature failure in some Australian coal mines might be linked to stress corrosion cracking (SCC) (Crosky et al, 2002). That study suggested the low impact toughness could be a major influence on the susceptibility to SCC of different steel compositions. A subsequent study involving laboratory corrosion tests however failed to confirm any link with metallurgical factors (Villalba and Atrens, 2007), a finding that is at odds with field experience. Some mine sites today are still reporting prematurely failed rock bolts to the rock bolt manufacturers; the failures are being identified at SCC induced. To this end a research project has recently been commissioned at University of New South Wales (UNSW), which aims to identify the environmental factors causing SCC, through field test sites and simulating the conditions within an accelerated corrosion laboratory. This paper outlines the methodology that will be used in this study.

Nov 25, 2010

By G B. Gnoinski

The Skorpion Zinc Mine and Refinery is situated approximately 25 km north of Rosh Pinah, south-western Namibia. The supergene zinc oxide deposit at Skorpion is hosted in a volcano-sedimentary succession within the para-autochthonous Port Nolloth Zone of the Gariep Belt. Rock types hosting the ore deposit include altered and metamorphosed volcaniclastic and clastic sediments, limestone and rhyolite. At Skorpion, the metallurgical process is unique and the plant design requires minimal fluctuations within a selected feed grade. In addition, the presence of limestone inter-fingered with ore in some areas of the deposit results in dilution problems which may increase gangue acid consumption and therefore processing costs. Hence, selective mining is necessary to ensure the delivery of suitable ore to the processing plant, in order to keep the overall operating costs at a minimum. A complex control system is in place and is capable of a high degree of selectivity. The paper describes the grade control system in place at Skorpion Mine which ensures that the qualities of the blocks planned for mining and the material being mined meet the stringent process requirements of the refinery, i.e zinc grade, gangue acid consumption and deleterious elements that may impact on the efficiency and costs of the metallurgical process. Keywords: Skorpion zinc, zinc oxide, supergene, volcano-sedimentary, grade control

Jan 1, 2007

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Dan Alexander, Ivan Crnkovic, Sarah Schwarz

"Several plant studies have been conducted at the Zinifex Century Mine over the past 5 years. For each of the plant studies, surveys of the zinc primary circuit were conducted, characterisation measurements for each operating cell taken, and the floatability components of the ore mapped to develop a model of the circuit. The floatability components and machine parameters were then used to simulate changes in circuit configuration and operating conditions, enabling further potential improvements in circuit performance to be identified.This paper reviews the current flotation practice at the mine, as well as various circuit changes and developments implemented by site. The application of the methodology and the evolution of the standard procedure are also discussed.INTRODUCTIONBase metals were first discovered in the Lawn Hill region of Queensland’s North West in 1869 and the first mining lease in this area was pegged in 1887 over what is now known as the Silver King vein deposit. The area encompassing these veins, which includes the Century deposit, was proclaimed the Burketown Mining Field in 1899. Exploration titles were granted to CRA in 1987, precisely 100 years after the initial discovery at Silver King, hence the name ‘Century’.Century was commissioned by Pasminco in late 1999, with the mine becoming fully operational on 1 March 2000 and the official opening taking place in April. Pasminco had bought the Century and Dugald River deposits from CRA in 1997 for A$345 million, and invested some A$710 million in bringing Century into production. Today, Century is the world’s second-largest zinc mine in terms of its output, having reached full capacity in 2003.The Zinifex Century Limited (“ZCL”) lead-zinc-silver deposit is located approximately 250 kms north-north west of Mt Isa in north-western Queensland. The deposit is a large flat-lying ore body covering an area of some 1.2 by 1.4 km, the 45 m-thick stratabound sulphide orebody is hosted within an 850 m-thick sequence of Proterozoic siltstone, shales and sandstone, amenable to open-cut mining methods. The mine has ramped up to full production delivering five and a half million tonnes of ore per annum, yielding approximately 900,000 tonnes of zinc concentrate and 90,000 tonnes of lead concentrate. Mine life is expected to be about 8 years"

Jan 1, 2008

General economic conditions continued to improve in the second quarter of 1984 as real gross national product advanced at an annual rate of 7.5 percent (table 1). This followed an even larger first quarter annual rate increase of 10.1 percent. The slower second quarter growth was greeted as a sign that the economy is not over-heating. The signs of slowed growth in some sectors suggest that the recovery may continue well into 1985 without the inflation symptomatic of a rapid recovery. Most of the slowdown in growth was absorbed by business inventories, personal consumption of durable goods, and residential fixed investment. Business inventories grew by only 68 percent as much as in the first quarter, personal consumption for durable goods grew by 58 percent of the first quarter rate, and residential fixed investment slowed to only 44 percent of the first quarter growth. Sectors with accelerated growth in the second quarter included personal consumption of nondurable goods and of services, which increased at annual rates of 9.6 percent and 3.8 percent, respectively, and Federal purchases of goods and services, which increased at an annual rate of 47.9 percent.

Jan 1, 1984

By Zenón Quispe

El presente trabajo describe la importancia de la aplicación de técnicas de análisis de cuencas sedimentarias en la exploración de minerales del área de Cajamarca. Para ello, se determinaron los espesores originales de las Formaciones Chimú, Santa- Carhuaz, Farrat e Inca y los porcentajes de disminución de espesor y con los resultados obtenidos, se diseño y analizó el gráfico de curvas corregidas por descompactación y sin corrección por descompactación. Asímismo, se explica la posible formación de fallas no tectónicas debido a la compactación diferencial y las unidades estratígráficas que comprende el estudio.

Sep 9, 2007

By Brown H. R, Wright E. A

The authors identify the workable coal seams, their distribution in relation to quality and economic occurrence and relate their analytical characteristics to industrial use. The development of established collieries is also discussed with regard to increased production demand.The authors also indicate the potential of the coal resources of the Southern District and postulate their ultimate development.INTRODUCTIONThe Southern Coalfield yields 30 per cent of the total production of bituminous coal in New South Wales. The economic potential of the coalfield was examined last by Harper (1915). Since that time additional knowledge has been gained by prospectors, mining companies and public authorities. Expansion in the steel industry and the building of power stations on the coalfields together with improvements in fuel technology, mining methops and road transport have resulted in production of coal from seams mice thoughtto have no economic value.DESCRIPTION OF THE COALFIELDFor the purpose of this paper the term Southern Coalfield includes also the South-Western Coalfield which together comprise the following Coal Districts:IllawarraDouglas ParkWollondilly-NattaiMoss Vale-Berrima (Hanlon, 1953).Geographically the coalfield is contained by the Illawarra Range in the east, the Shoalhaven River to the south, the Wollondilly River to the west, and in the north by a line...

Jan 1, 1958

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper/gold mine has continued to process significant quantities of complex transitional mixed ores. The effect of the complex mineralogy on the flotation performance is depicted. Initially, ore treated came predominantly from accumulated stockpiles. In the ensuing years, ore treated shifted to primarily freshly mined ore that generally showed less tarnish with better float kinetics but with the downside of producing lower concentrate grades. A number of changes were made to improve the efficiency of the roughing circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory float test work done and discussed at length in a previous paper. Salient among the adopted recommendations from previous work were increasing circuit capacity and modifying configuration to increase the residence time and the number of sulphidisation stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and subsequently below-specification final concentrate product. This was primarily due to higher mass pulls resulting from the extended rougher bank with multiple concentrate discharge streams. This necessitated the need for an enlarged cleaning capability to offset this. The extra cleaning capacity came on-stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. INTRODUCTION The Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining PLC, a First Quantum subsidiary. The remaining 20% is owned by the state through the parastatal ZCCM. The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005. Prior to June 2009, Kansanshi mine treated only two ore types: oxide and sulphide. All transitional ores mined during the period leading up to 2009 were stockpiled. The treatment of the minerologically complex, transitional ores through a third train commenced in June 2009 but with numerous metallurgical challenges. This transitional ore (called mixed ores) could not be previously treated economically due to high gangue acid consumption (GAC) minerals association (making it unsuitable for the oxide float–leach circuit) and poor flotation response ruling out the conventional sulphide float circuit. The new novel circuit involved a conventional sulphide pre-float followed by flotation involving staged controlled potential sulphidisation (CPS)."

Jan 1, 2015

In a field test at Mount Isa Mines Ltd., a system developed by ICI Australia Ltd. for bulk loading "MOLANITE", an ammonium nitrate slurry blasting agent into ring drilled holes of wblcvel open stopes, was shown to be satisfactory. The fragmentation produced by the slurry was a significant improvement over ANFO and the stope production rate was increased by approximately 50%. Indications are that the charging rate and labour costs will not be greatly changed if a slurry system is used.

Jan 1, 1973

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939

By U. Paschedag, H. Bussmann

"Bucyrus manufactures the most comprehensive product portfolio of mining equipment worldwide. Its mission is to have a positive, lasting effect on our world. Bucyrus makes sustainable development a fundamental way of doing business through economic, environmental and social initiatives that support, educate and benefit our employees, customers, shareholders and other stakeholders. Our participation in GRI (Global Reporting Initiative), a network-based organization that has pioneered the most popular sustainability reporting framework will be discussed as well as examples will be given on each major field of engagement. Two examples from surface machinery are most fuel efficient haul trucks as well as the Highwall mining system which allows access to coal reserves which are lost not making use of this kind of system. Two examples from underground machinery are Bucyrus’ automated plow systems for the mining of medium and thin coal seams with minimum rock and Bucyrus’ intelligent CST drive system for high-powered armored face conveyors (AFCs) for efficient use of energy."

Jan 1, 2011

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

Komatsu America International has introduced two new hydraulic excavators. They can work in congested and confined areas. The tight tail swing radius of the PC128US-2 and PC22-8USLC-2 enables the excavators to minimize the work space. The units can operate in confined work settings that are inaccessible or counterproductive to traditional machines. Even the door is designed for tight working conditions. A convex door slides open along the exterior curve of the cab, rather than swinging out on hinges past tracks. And the excavators’ tight tail swing design allows them to load within the track width of the machine.

Jan 1, 2000

By Axel Nitschke, Josef Arnold

Bochum’s Underground Lot 306 was characterised by a confined site and unique tunnelling methods. A highly mechanized construction concept was developed to achieve high progress rates. Bespoke backup systems for muck disposal and material supply were used. For the first time in suburban tunnelling, wet shotcrete, batched onsite, was applied. A three-storey underground car park had to be undermined with only1.5 m of overburden and had to be lifted several times by “compensation grout in.” An existing operational two-lane metro tunnel was enlarged without any major impact on train operation.

Jan 1, 2005