Search Documents

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By Esteban Bravo

El presente señala la utilidad del último software y equipos desarrollados como herramientas que permiten analizar, monitorear y reparar los problemas que se presenten en el funcionamiento de motores diesel, además de disminuir los costos para su mantenimiento.

Aug 25, 2002

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By Harold M. Smith

Natural gas has been used as a fuel and source of energy almost from its discovery, but its use as a chemical raw material may be said to have begun in 1918, when Brooks and Humphrey3/ showed. presence of alcohols in the diluted acid oil obtained by the sulfuric acid-treatment of cracked petroleum distillates. However, development of the utilization of natural gas for chemical syntheses was slow, partly because erroneous ideas existed regarding the nonreactivity of tine hydrocarbons composing natural gas. Data accumulated by petroleum chemists throughout the world, particularly since about 1930, have shown that these hydrocarbons will react when activated by the effects of heat, pressure, chemical reagents, and light; also that the reactions can be made to proceed of practicable speeds and to provide good yields of useful products with moderate operating conditions, especially if catalysts are employed. As those results became known, the possibility of a synthetic organic chemical industry based upon these reactions became apparent, and today this industry is large and growing rapidly in importance. In this paper the story of the manufacture of chemical products from natural gas is told simply in graphic form. The industry is developing so rapidly that soma products may have been omitted, but every effort has been made to include all that are important or likely to become so. The difficulty of keeping information of this tape up to date is shown by reference to an information circular4/ or, the sore subject published by the Bureau of Mines in 1930, in which the important products are shown on a single chart, where as five charts are employed for the cane purpose at present.

Jan 1, 1940

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

By H. Gerry Stephenson, Devin Castendyk

"One of the most important environmental issues associated with contemporary openpit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following:• The water quality within the pit lake, plus surface water and ground water discharging from the pit lake, meets premining or other acceptable water quality conditions of the receiving environment. • The termination of all active treatment processes.• The return of the pit lake to the government for long-term care and maintenance.• The release of the mining company from all future liabilities associated with the pit lake.• The return of the environmental bond to the mining company.• The reuse of the pit lake for some post-closure, beneficial purpose.The achievement of these goals is known as walk away pit lake closure.Peer-reviewed publications of successful walk away, pit lake closure provide mining companies with the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). In North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources (Vandenberg, 2018; Crossman, 2019). The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need to document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry, at large, can learn from these examples and can better address public concerns."

Aug 1, 2019

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By E. C. Grunsky, B. W. Smee

"The development of low-cost, rapid multielement analytical techniques has generated large geochemical databases in many exploration programs. When a sampling program consists of several thousand samples, the resulting data matrix is enormous and effective interpretation using all of the elements individually becomes burdensome. However, the application of multivariate statistical techniques can extract geochemical patterns related to the underlying geology, weathering, alteration and mineralization. Imaging the results over topography enhances the interpretation of these patterns. Examples of this approach are shown from mineral exploration programs in Canada and Mexico. IntroductionThere has been a dramatic change in the effectiveness of using geochemical survey data in the past ten years. This is mostly due to:• lower cost of geochemical analysis;• lower detection limits;• new methods of multi-element analysis;• a marked decrease in the turnaround time;and• the intelligent use of computers in presenting geochemical data.Geochemical surveys commonly have two objectives: locating abnormal concentrations of ore-forming or pathfinder elements and characterizing the underlying host lithologies. Geochemical surveys often employ a wide range of sample media that may typically include whole rock lithogeochemistry, various soil horizons, till and basal till sampling, stream sediments, lake sediments, and various forms of weathered regolith. Each of these sample media will exhibit a unique element distribution that must be factored in the interpretation phase of a geochemical survey study. This can become a cumbersome process if univariate data handling methods are employed."

Jan 1, 2003

By R Castedo, L. M. Lopez, J. A. Sanchidrian

In 2014 the authors presented results from 13 tests made with two blasting seismographs on a vibration exciter. They measured coupling transmissibility as function of frequency (i.e. ratio of the velocity of the sensor mount to the velocity of the ground motion) from 16 to 200 Hz at one or two vibrations levels (5 mm/s or 0.2 in/s, and 20 mm/s or 0.79 in/s) with mounts freely placed, sandbagged, and anchored to a granite slab firmly attached to the plate of a vibration exciter. As the memory capacity of one of the seismographs prevented to cover low frequencies, e.g. 4-16 Hz, a new measuring campaign has been recently made to extend the study down to 2 Hz. In this campaign, two more techniques, in which the sensor mounts were fixed with thermal adhesive or a combination of duct tape and gypsum plaster, have been also investigated from 2 to 200 Hz at 5 and 20 mm/s. Free and sandbagged mounts lead to a weak coupling of the mounts to rock, so that transmissibility depends on the characteristics of the imposed rock motion (peak velocity and frequency). Measurements are accurate only at low frequencies (below 17 Hz for free mounts and 10 Hz for sandbagged) in the tested conditions (velocities up to 20 mm/s). Above these frequencies, ground motion in the measurement can be modified by a factor of 0.16 to 1.22. Anchored, glued and plastered mounts achieve a stiff rock-to-ground coupling, ensuring consistent measurements for the frequencies commonly found in blasting independently of the vibration level and the mount characteristics

Jan 1, 2015

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By James K. Richardson

Today, the enigma of the "missing man" in the metal mining industry equals, and frequently surpasses in objective importance, the problems of ore development, drilling, sampling, pumping, milling techniques, geophysical prospecting, or any one of a hundred highly technical subjects. Unfortunately, as engineers, we have confined our attentions, in the main, to the scientific phases of mineral technology, relegating our man power problems to the background. But what good has all our scientific study and preparation been if we can't get the ore mined, milled, or smelted? What has happened to our labor supply? Where is the good old miner who could timber, drill a round, lay track, or do any job underground?

Jan 1, 1949

By Wilson A. F

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recept studies have emphasized the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d18O values. Preliminary oxygen and carbon isotopic data for some important gold deposits of eastern Australia have emphasized the diverse origins of their ore fluids.The Mount Morgan gold-copper orebody is shown to be of the volcanogenic massive sulphide type with ore fluids predominantly of sea water origin. The Charters Towers fissure veins formed during hydrothermal activity associated with intrusion of Lolworth Igneous Complex equivalents. Oxygen isotopic studies of the quartz reefs at Stawell and Gympie have been inconclusive. The ore fluids have a d18O value of about 7 per mil and may be of magmatic or metamorphic derivation.

Jan 1, 1981

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

By Z S Chang, T F. Zhou, G X. Zhong

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yaojialing zinc-gold polymetallic deposit is a newly discovered, large skarn deposit in the Middle-Lower Yangtze metallogenic belt, East China. It is located in the transitional zone between the Tongling uplift block and the Fanchang faulted basin. It is mainly hosted in the contact zone between early Cretaceous granodiorite porphyry and Carboniferous-Triassic limestone, or occurs in limestone xenoliths within the intrusion. Skarn and stratabound massive sulfide orebodies are the primary ore styles. Sulfide ?34SV-CDT values indicate a magmatic sulfur source, in common with most deposits in the Tongling block. Calcite d13CV-PDB and d18OV-SMOW ratios reveal that marine carbonates were the major source of carbon in late-stage hydrothermal fluids. The calcite probably formed during interaction between magmatic fluids and carbonate wall rock.CITATION:Zhong, G X, Zhou, T F and Chang, Z S, 2015. Geology, chronology and isotope geochemistry of the Yaojialing zinc-gold deposit, Tongling ore district, Anhui Province, China, in Proceedings PACRIM 2015 Congress, pp 457–462 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M F. Jennings, N J. Corlis, B J. Thomas, L N. Tylkowski, A E. Petts, G D. McDonald

Flinders Mines is an iron ore explorer and developer with a tenement package located in the Hamersley Ranges region of Western Australia, approximately 70 km north of Tom Price. Exploration over the past five years has identified a Global Resource in excess of 900 Mt at a grade of 55.2 per cent Fe (+50 per cent Fe cut-off). This resource is spread across multiple deposits and has been divided into a number of mineralisation type domains. These domains are comprised of transported hematite rich detrital iron deposits (DID) and goethite dominant channel iron deposits (CID) as well as in situ bedded iron deposits (BID). The BID at PIOP is low in alumina and silica with a high calcined iron content making it an attractive exploration target. BID exploration techniques include a combination of mapping, structural analysis, downhole gamma logging and 3D geological modelling. Relationships identified between existing BID mineralisation, geology and structure has aided in targeting additional mineralisation across the tenement and highlighted other previously untested areas that warrant further investigation.CITATION:Tylkowski, L N, Corlis, N J, McDonald, G D, Petts, A E, Jennings, M F and Thomas, B J, 2013. The hunt for hydrous bedded iron deposits - an investigation into Flinders MinesÆ Blacksmith Tenement, in Proceedings Iron Ore 2013 , pp 121-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013