Search Documents

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By Jeff Wachendorf

As the title implies, this paper details the start of a cast blasting and the design flexibility required to satisfy different parameters encountered on a large coal mine employing cast blasting as the program has grown and evolved around the town of Colstrip, Montana. As strip ratios have increased, the need to adapt and find solutions to provide coal at a reasonable cost to the mine mouth power plants has risen. Colstrip, Montana has a long history of coal mining which dates back to the early 1920s when Foley Brothers began supplying coal strictly for powering locomotive engines.

Jan 1, 2015

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch

An advanced laboratory-scale weathering apparatus has been developed at McGill University to study the effects of weathering (ambient temperature oxidation) on the self-heating of sulphides. Previous work by the authors has shown that the problematic self-heating of sulphides is inherently linked to the degree of oxidation (weathering) of the minerals: un-oxidized active sulphides exhibit little or no self-heating while the same material when weathered can generate extensive self-heating bringing temperatures well above 100 0C. In this study the effects of environmental conditions (weathering time, ambient temperature, sample moisture, relative humidity, and oxygen content) were evaluated with respect to the self-heating response of a pentlandite-pyrrhotite nickel sulphide concentrate.

Jan 1, 2015

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By T. Matthews

"One critical factor in mineral reserves reporting, as well as mine-reserves reconciliation, is the impact of dilution and ore loss in the mining process. This paper considers the implications of various factors on dilution and ore loss projections, by orebody geometry, mining method, and ore control systems. We also discuss the implications of resource estimation methodology on dilution for reserves. DEFINITIONS Dilution and ore loss are two critical concepts in mining, which address the differences encountered between modeled grade and tonnages and actual production. Dilution is volume increase and grade reduction caused by multiple factors, chief among which are mining of waste material along ore-waste contacts, mining of internal waste as ore, and misclassification of waste as ore in the ore control process. There are also geostatistical and estimation aspects sometimes lumped with dilution, including the volume-variance effect (the tendency for small volumes of material to include a less regular distribution of grade than large volumes of material). Ore loss is described as reductions of ore volumes in the mining process due to misclassification of ore as waste in the ore control process, exclusion of discontinuous mineralization from mining due to geometry or continuity, and mechanical losses in the mining process. Dilution is typically taken as an increase in tonnes of ore with no change in contained metal (and thus results in a reduction in grade.) (Some workers consider the likely grade of the diluting material as well, particularly in deposits with gradational grade boundaries—this will be addressed later in the text.) Ore loss is typically taken as a reduction in tonnes at average grade of the ore, and thus results in a reduction in both tonnes and contained metal. If model (resource) tonnes are Mt, grade is Mg, and contained metal is Mm, the resource with ore loss (L) and dilution (D) included (Rt, Rg, and Rm) will be:"

Jan 1, 2015

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By Yongquan Zhu, Zhengguo Zhu, Zhichun Liu, Chao Kong, Xinqiang Gao

"The aim of the study is to have a good understanding of the change in the seepage field during and after the tunnel excavation in weathering alteration rock. Field tests are used to monitor the changes of the water table and the numerical model is used to analysis the influence of the seepage filed with different operation conditions during and after the tunnel excavation. Results indicate that the depth, diameter and pumpage of precipitation well are the main factors that have a great influence on the drainage effect. Results also indicate that different operation conditions had various effects on the decrease in water yield during tunnel construction and the recovery in groundwater level after construction.INTRODUCTIONAs a potential disease during tunnel construction, Gushing water not only affected construction schedule, increased construction cost, as well as affected tunnel stability and safety during operation, but also decreased ground-water level. What’s more, the fall of water table caused by gushing water in tunnel would have influenced surrounding residents’ living water, agricultural water and ecological environment around tunnel. In recent years, enough emphasis has been paid to the influence on environment due to the construction of tunnel as a result of the reinforcement of people’s environmental protection awareness.As a result of water collection and drainage after excavation, groundwater was discharged into the tunnel, which caused a loss of water resources in the adjacent mountain mass. Furthermore, during tunnel operation, it was difficult for groundwater level to resume its original condition, which caused a bad ecological environment, because drainage system during tunnel construction destroyed its original hydrologic dynamic balance.In order to study whether decreased groundwater level resulting from tunnel construction could be restored during operation to its original condition, this paper gave a field monitoring on tunnel displacement during construction and simultaneously, generalized model of regional hydrogeology was created according to field hydrogeology to carry out a calculation of stable seepage flow and draw comparisons between recovery conditions of various water levels."

Jan 1, 2015

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By I. Ruiz Bustinza, L. F. Verdeja, Daniel Sbarbaro, R. Parra, J. Mochón

The oxidation of sulfides is a complex process involving gaseous products and intermediate species given rise to emission and absorption spectra which carry out important information about the reaction process. This information could be used for on line monitoring of pyrometallurgical reactor if the appropriate sensors were available. We present in this paper an analysis of the concept that has been successfully applied in iron and steel making industry, as well on fuel combustion control, where the spectra measurement gives the possibility for online monitoring and automatic control of high temperature processes. This concept has not been widely applied in the nonferrous pyrometallurgical primary production. The design of new sensors is discussed from the analysis of spectra measurements during flash combustion of copper concentrates at laboratory scale.

Jan 1, 2015

By Viraj Parekh, Kinnor Chattopadhyay, Sina Mostaghel, Xiao Zhang

Electric arc furnace steelmaking is a dominant approach in North America and controlling EAF emissions is a key issue today because of stringent permit limits imposed by various regulatory bodies. In the present study, an attempt has been made to mathematically model EAF emissions, and use the models as a predictive tool for fine tuning the process. CFD modelling has been used to model various fume release scenarios, and optimize the exhaust conditions for maximum capture. Thermodynamic calculations have been used to analyze various chemical reactions which lead to the emissions of hazardous air pollutants with special emphasis on Zinc, Lead and Manganese.

Jan 1, 2015

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015