Search Documents

By E. Yasar

This paper describes the use of the sand and plaster physical modelling technique to investigate the deformation around mine roadways using a variety of support methods in a particular form of stress field. The characteristics and conditions of coal measures rock were considered prior to the preparation of the models and the insertion of support The investigation has clearly shown how floor lift, roof failure and sidewall movements of mine roadways in laminated weak rock conditions gradually develops as a result of the increase in the stress and, also, how it is related to the level of support used.

Jan 1, 1995

By Anthony Iannacchionc, Jessica Benner, Harold Miller, Megan Witkowski

"Longwall bituminous coal mining has been practiced in Pennsylvania since the 1970""s. Hundreds of longwall panels have been mined during the last 40 years but only 24 have actually undermined Pennsylvania's Interstate Highway System. The impact to interstate highways are summarized in this paper and the factors that influence the magnitude of these impacts are examined.INTRODUCTIONOver the last 30 years, interstate highways in Pennsylvania have been undermined by portions of 21 bituminous coal mine longwall panels. From 2003 to 2008, three of the panel were extracted by the Emerald Mine and six by the Cumberland Mine both in Greene County and both owned by Alpha Resources. Previous assessments of longwall mining under Pennsylvania’s interstates have identified impacts to the highways but no danger to public safety. In general the magnitude and extent of impacts during the recent undermining of Interstate 79 or 179 appears to be similar as those identified in previous studies. The nine longwall panels are among some of the widest in the U.S. They are supercritical in character with overburdens ranging from greater than 152 m (500 ft) to less than 305 m (1,000 ft).The Pennsylvania Department of Environmental Protection (PA DEP) requested that the University of Pittsburgh summarize observations collected by their staff during the recent undermining of 179. Observations and photographs of impacts to the highway were made by PA DEP staff and entered into reports prepared by California District Mining Office (COMO) staff and statements written into the Bituminous Underground Mining Information System (BUMIS) database. In addition to the observations by the PA DEP, the Pennsylvania Department of Transportation (PennDOT) conducted a series of detailed land surveys along portions of the highway undermined from 2003 to 2008. To characterize the subsidence basin fanned by longwall mining. PennDOT information has been analyzed by another research group within the university (Guticrre7, et al., 20 I 0)."

Jan 1, 2010

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

Numerical simulation for microseismicity due to mining at one of the collieries in Australia was carried out and the results were compared to the observed microscismicity. 3-D Stress analysis showed stress concentration on the edges of the mined areas and on the coal pillars- The stress concentration ahead of the coal face was biased to the tailgate. This is similar to the observed distribution of microseismic events. Stress reduction above and below the mined area was seen. Tensile stress was observed mainly above the mined area. It was realized that compressive failure due to nearly vertical maximum principal stress and nearly horizontal minimum principal stress in retreat direction (NS) might occur ahead of the face. Tensile failure due to nearly vertical minimum principal stress above the mined area was expected. Compressive failure due to nearly horizontal maximum principal stress in EW direction and nearly vertical minimum principal stress above and below the mined area were also expected.

Jan 1, 2001

By Yun Zhang, Haijun Jiang, Shenggen Cao, Chen Wang

The distribution of front abutment pressure is closely related to the force, deformation and energy distribution of hard roof before periodic weighting. So it is necessary to carry out research on the relationship between them. According to front abutment pressure distribution feature, using the location of peak front abutment pressure as the dividing point, coal seam is divided into two parts along the direction of mining: the yield zone that is the area between the faceline and the point where the maximum front abutment pressure occurs, and the elastic zone that is the part before the point of peak front abutment pressure. The proposed mechanical model of unit width hard roof at the panel center periodic weighting consists of five parts including the yield zone. All parameters of the deflection equations for each of the five parts that satisfy the continuity conditions and natural boundary conditions are obtained by using the Matlab software. The continuous curves of front abutment pressure, deflection, bending moment and bending strain energy density distribution of hard roof are obtained by iterative approximation method. The following conclusions can be drawn through analyzing those curves: (1) The position of peak front abutment pressure is located at the transition of coal seam foundation from yield zone to elastic zone (elastoyield critical point), the distance of it to the faceline is equal to the width of yield zone. The peak front abutment pressure increases with yield zone with. (2) The peak bending moment in front of the faceline, and the distance of it to the faceline increase with the yield zone width. The deflection of hard roof at the face and midspan also increase with yield zone width. (3) As the yield zone width increases, the accumulated elastic energy of hard roof in front of the faceline increases, and the core zone of energy moves forward away from the face. (4) When the yield zone width is zero, the whole coal foundation is regarded as elastic foundation, and the peak front abutment pressure occurs at the faceline.

Jan 1, 2015

By Christopher Mark

Dr. Christopher Mark serves as Team Leader of the Rock Mechanics Section in the Rock Safety Engineering Branch of the NIOSH - Pittsburgh Research Laboratory. In this position he leads a multi-disciplinary team and conducts individual research directed towards fundamental ground control safety issues affecting miners. Dr. Mark is recognized as one of the country?s leading authorities on coal mine ground control. Through his research, he has made numerous important contributions to mine safety that have been widely adopted into mining practice. He is a highly original researcher, and has often developed new and innovative methods to tackle extremely complex problems in his field. In recent years Dr. Mark has also achieved wide international recognition. Five research projects in Canada, Australia, and South Africa have been based largely on his work.

Jan 1, 2007

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By Rene Rodriguez

Sandstone paleo-channels encountered during coal mining operation can significantly slow down the advance in mining, and often completely shut-down coal mine production, with consequent extensive economic losses to the mine operator. Definition of the encountered channel usually involves intensive drilling; vertically from the surface and/or horizontally from underground vantage points. Coal operators with limited resources often resort to exploration by extending mine faces toward the channel. Both drilling and underground mining exploration are prohibitively expensive and usually provide only partial information about the location, size and shape of the sandstone channel. A low cost alternative which can also provide a more comprehensive picture of the channel is the application of Underground High Resolution Seismic Methods (UHRSM) developed and successfully tested by GECOH Exploration. UHRSM applies surface seismic reflection technology rotated as needed (usually 90 degrees) to accommodate the faces of the exposed channel, coal rib, or coal in front of the inclusion (sandstone channel, etc.). This entails placing high frequency seismic sources and geophones horizontally across these exposed faces. Refraction and reflection events from the front and back of the channel are isolated, analyzed and inverted, to calculate the channel's location and geometry. This paper presents a summary of the geophysical exploration technique and two case history examples where it was applied. In the first case, the accuracy of the technique was verified through subsequent mining. Mining is yet to commence in the second case. Both cases were applied to room-and-pillar nines where the irregular rib lines significantly extended the data processing effort. This suggests that UHRSM will find the easiest application when used along straight rib lines, but that is not a requisite to the application. The UHRSM should find ready application in longwall mining to delineate sandstone channels and other non-coal inclusions in the middle of the panels or ahead of the gate road faces.

Jan 1, 1994

By R. Karl Zipf

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINE TAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress¬strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory¬scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle (0) for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and 0 values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

Jan 1, 2003

By James H. Fletcher

Much data and experience has been accumulated, especially in the last 5 or 6 years, to show that modern roof trusses, both of the Birmingham type and the bolt-and-channel type, perform well to support certain kinds of coal mine roof. For some time now, roof trusses of the Birmingham type have been effective in controlling thick shale roof, which tends to sag and fall over a period of about eight weeks. These falls leave dame-shaped cavities which are reminiscent of the pressure arch theory of roof failure. Lately there has also been significant interest in supporting some longwall panel entries with channel and-bolt systems. These systems utilize two vertical center bolts and two 45 degree end bolts through a heavy gage channel. Both types of truss systems have long bolts, which require 8 to 9 Foot holes on a 45 degree angle, and point anchor resin bolts, which utilize a 2 or 3 foot rebar grouted in a thin annulus of polyester resin. Consequently, many coal mining people have been impressed with the very good anchorage characteristics and tensionability features of these systems. However, the same people have been proportionately dismayed to find that very often the most difficult part of introducing a trussing program to a mine is deciding on the machine specifications which determine the truss installation rate. The purpose of this paper is to indicate aspects of truss bolter design and use which are not shared by roofbolter design and its vertical pattern of bolts. Of the two types of drill units conventionally accepted, arm feed units and mast units, only one 15 judged suitable. While the arm feed unit offers low collapsed height with a long drill feed length, a great attribute for low seam use, it has not lent itself to being rolled over to a 45 degree angle. One reason for this inability is that many items which are conventionally mounted on the arm feed unit cannot be allowed to rotate with the unit. These items include drilling controls, tool Cray, lights, canopy or safety post, panic bar, and stab jack(s). If these items were independent of the arm feed drilling unit, they would have to be out of the way of the boom arms, links, and feed cylinder as the unit moves. To ease this problem, the arm feed unit can be made very short and even mounted across the machine. However, the resulting short feed length is undesirable. Several short drill steel extensions are required to drill a relatively long hole, making this procedure time-consuming as well as increasing the likelihood of drilling a crooked hole. Another reason for abandonment of the arm feed unit is that a very stiff drill guide (or "centralizer") is required to start the hole. Using the mast tilt control, the roof bolter operator will force the bit against the roof and will rotate the bit without feeding to cut sideways into the roof to form a hole face. Omission of this step often results in the skidding of the bit toward the rib. To date, no such sturdy drill guide has been designed for an arm feed drill unit. The mast style unit has been the most successful design for angle drilling. It is easily rolled over to a 45 degree angle or to 90 degrees and, on single head models, often has been made to roll through 180 degrees. The mast style is compact, in plain view and is easily fitted with heavy duty manual or hydraulically operated drill guides. It can be mounted directly on a machine chassis, or onto a swinging boom, or onto a slider arrangement in a broad variety of configurations which will accommodate controls, tool trays, stab and roof support jacks, lights, canopies, and panic bars. The only significant difficulty with mast drilling units occurs in lower mining heights when desirable low mast height is accompanied by undesirable short feed length. While the lead extension in the drill string can be as large as the mining height will allow, a short feed length will permit only the use of shorter middle extensions and drivers, and perhaps will. require the use of two different length wrenches. The associated problem is the relatively short distance from the drillhead to the drillguide. This distance is further shortened when raising the drillhead to get the bit to the roof. One might keep longer lead extensions on the machine; drill a vertical pocket for the bit, starting the angle hole at this pocket; or modify the mast. If the mast is made so that the distance from the drillhead to the drillguide remains constant while the mast extends, after which the drillhead travels up the mast, the shorter mast can be made to start the hole more easily. However, short teed length will still result in longer drilling time. It is obvious from these points that a proper choice of mast is simply the highest one which will be moved easily in the given mining height. This, of course, goes against the grain of most experienced coal mining people who realize that a relatively small decrease in mining height can create a problem correctable only with the purchase and installation of shorter masts. If the mining

Jan 1, 1982

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Changshou Sun

The geotechnical properties of mining zones at Leeville Underground mine (or simply called Leeville mine through this paper) are different from one zone to another. The typical ground condition is poor to very poor. Therefore, an appropriate ground control practice is the key for the successful and smooth ore production at Leeville mine. Based on the available geotechnical data, the empirical and numerical methods are used to design the right ground support systems. The main ground control practice at Leeville mine includes geotechnical data collection, evaluation of the stiffness of the support system, selection of rock bolt types, design bolt length and bolting patterns, development of the ground support standards, and performance of quality controls on bolt installation to ensure proper rock anchorage, and strength of shotcrete and backfill. Through all these activities, an appropriate ground support system has been established and applied at Leeville mine for the past four years. So far, a good result related to successful ground control and smooth ore production has been achieved, although the system is still being improved. The authors of this paper will summarize the ground control practice conducted in the last four years and will discuss the procedures and standards of establishing the appropriate ground support systems for Leeville mine.

Jan 1, 2013

By Kirk W. McCabe

RokLok binder is a two-component polyurethane system consisting of a polymeric isocyanate (Component A) and a polyol resin (Component B). The two chemicals are mixed and injected into the mine rock under pressure. The initial low viscosity enables the RokLok material to permeate many of the smallest fractures. About 3-5 minutes after injection, the reacting material begins to expand in the fractures; the reaction is completed after 1-2 hours, and the material sets to a mechanically strong binder which adheres tightly to the rock. The consolidated rack provides resistance to any further f movement w thin the strata. The RokLok binder injection system is fast becoming an important engineering tool for coping with adverse underground geological conditions. Two case histories discussed in this paper, a longwall mining problem and an entry-roof problem, demonstrate the effectiveness of using the RokLok binder system to help solve complex ground-control problems in a cost-effective manner.

Jan 1, 1981

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By Denise Y. Dizon

The objectives of this study were to document the hydrologic impacts of longwall mining on streams, identify the factors affecting the extent of stream dewatering, and develop empirical trends to predict the extent of dewatering and recovery of streams in advance of mining. This study on stream impacts is a companion to a stud; conducted on ground water impacts from longwall mining, which was done as part of the same research project at the' same locations and times. The study areas are three mine sites in north- central West Virginia. Mine A, located in Upshur County, has relatively thin mine overburden under the valley streams (105-115 feet). Stream monitoring there continued the earlier work of Cifelli and Rauch (1). Stream dewatering was severe with streams often going dry over the longwall panels during baseflow conditions. The lost water was probably flowing to the mine. Dewatering began in streams over the mine entry areas adjacent to the panels and as much as 380 feet from the nearest panel edge. The angles of dewatering influence ranged 22 to 72 degrees with respect to the nearest mined panel edge. Discharge then typically increased as the streams- flowed across the panel edge, but then decreased again over the panels. These streams were often ponded by local reversals in hydraulic gradient caused by land subsidence, and often dried up after flowing a few hundred feet across the panels. This occurred over panels that were previously mined up to eight months before. Mine B, located in Monongalia County, has relatively thick mine overburden (475-485 - feet) under the major stream. Stream dewatering was severe there during warm season baseflows, with complete dewatering occurring then over the longwall panels. This dewatering occurred over mined panels up to five years old, probably in response to a major anticlinal axis lineament and fracture zone in the stream valley. Mine C. located on the West Virginia -Pennsylvania border, has relatively thick mine overburden (about 585-630 feet) under the monitored streams there. stream dewatering was only partial, and these streams typically recovered their lost discharge downstream of the mine, indicating that lost water was not recharging to the mine. Only longwall panels less than one year old were associated with stream dewatering.

Jan 1, 1990

By D. J. Maconochie

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modern houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various house designs.

Jan 1, 1992

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Pieter-Jan Kleiterp

Caterpillar has been involved in highwall mining since the purchase of Bucyrus in 2011. The Cat® HW300 is a continuation of the Superior Highwall Miner that was first sold in the USA in 1994. Currently, there are more than 80 machines supplied worldwide, and Caterpillar envisions increasing the population steadily in the coming years. The Cat highwall miner product group, based in Beckley, WV, has been involved in the sales of all miners to date. With the dealer model that Caterpillar is using, more people, dealers in particular, need to be trained on the application of highwall mining. A site investigation is a highwall specialist?s work, and Caterpillar assists dealers and customers in determining the technical feasibility of highwall mining on mine sites. With the ever-increasing amount of requests, it proved to be important that people without highwall mining expertise, yet who are familiar with mining, could perform a very quick analysis of a potential highwall mining site to determine at an early stage if it is worthwhile to invest the time and money of all parties?customer, dealer, and Caterpillar?in further follow-up. Therefore, Caterpillar would like to introduce the Cat HW300 QuickScan tool.

Jan 1, 2014