Search Documents

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By G. J. Hasenfus

Although theoretical and conceptual knowledge regarding the impact of horizontal stress on underground coal mining excavations have existed since at least the mid-1900s, it wasn?t until the late 1970?s that the theory and practical understanding began to mesh. Since that time, particularly over the last 25 years of this Conference, increased empirical study, as well as advances in measurement technology, computer simulation, and bolt design, has significantly improved our understanding of horizontal stress impact, and provided coal mine operators with tools to reliably predict and manage it. This paper provides a retrospective review of some of the more important horizontal stress-related advancements made during the 25 years of Conference proceedings, particularly those for predicting and controlling horizontal stress impacts within underground coal mines. Relevant and significant CONSOL experiences and studies will be presented in context, with particular attention to horizontal stress considerations for longwall faces and gateroads. The significance of horizontal stress will also be placed in context with respect to local geology and structure, ground support measures, and mining configuration, method, and sequence.

Jan 1, 2006

By Greg Hendon

Various methods have been used to evaluate the effectiveness of shields in place. The most common method used is static recording of leg pressures by visually examining pressure gauges. In an effort to more closely examine the shield cycle and therefore the shield effectiveness, Jim Walter Resources has implemented a program of monitoring utilizing a polycorder system which is capable of recording convergence and pressure measurements on a continuous basis. This paper will discuss two longwall panels at Jim Walter Resources which have been monitored.

Jan 1, 1990

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By Keith A. Heasley

Exactly 25 years ago this month (August 12, 1981), IBM introduced the ?Personnel Computer? with a 16 bit operating system called MS-DOS 1.0. Since then, Moore?s Law, which essentially states that computer capability will doubled every 18 months, has been fully evident in the computer industry. As computers have advanced from main frames to initial personnel computers to the powerful graphical workstations of today, numerical modeling for ground control in mining has followed closely behind. Twenty five years ago, many numerical methods for solving ground control problems were little more than equations on a piece of paper. In the intervening years, these numerical models have grown from initial trial programs to highly-complex computational systems with numerous capabilities for different material behavior, failure criteria, gridding methods, discontinuities, etc. In some instances, the capability of the programs has quickly outstripped the geo-technical modeler?s ability to get accurate, realistic input and boundary conditions. This paper will look at: how numerical models have evolved in the last 25 years, how the models have been applied to ground control problems in that time period, and where numerical modeling is headed in the immediate future.

Jan 1, 2006

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By David Oyler

Sonic travel time logging of exploration boreholes is routinely used in Australia to obtain estimates of coal mine roof rock strength. Because sonic velocity logs are relatively inexpensive and easy to obtain during exploration, the technique has provided Australian underground coal mines with an abundance of strength data for use in all aspects of ground control design. However, the technique depends upon reliable correlations between the unconfined compressive strength (UCS) and the sonic velocity. This paper describes research recently conducted by the National Institute for Occupational Safety and Health (NIOSH) aimed at developing a correlation for use by the U.S. mining industry. At three coreholes in Illinois, Pennsylvania, and southern West Virginia, sonic velocity logs were compared with point load tests for a broad range of coal measure rock types. For the entire data set, the relationship between UCS and sonic travel time is expressed by the following equation, where UCS is in psi and t is the travel time of the P-wave in microsec/ft. UCS = 468,000 x e-0.054t (1) The r-squared value for this equation is 0.87, indicating that a strong correlation between sonic travel time and UCS can be achieved with this technique. The paper also addresses the steps that are necessary to ensure that high-quality sonic logs are obtained for use in estimating UCS.

Jan 1, 2008

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Scott A. Shapkoff

High strength cable strand supports are predominately used as a supplemental means of ground control in longwall and development operations in the U.S. The advantages of cable strand supports have been documented and include flexibility, strength, and ease of installation. Since the majority of cable supports installed in the U.S. today are partially grouted, and this same segment of supports has no inherent installed tension, the supports are considered currently arbitrarily strictly supplemental and therefore, cannot currently be deemed primary support (in most mining districts). This paper details and discusses two distinctly different configurations and the technical advantages of active partially grouted cable supports for certain primary support applications. The evolution of the designs for both systems is highlighted. Field data illustrates the amount of active load in relationship to installed torque and the affects that component variables have on this load measurement. Roof control patterns using active cable supports are examined as alternatives for combination patterns using primary and supplemental systems. The importance of maintaining consistent installation procedures plays an important role in the level of performance of the system. Economics comparing the installation of active cables with other primary/supplemental patterns is also included.

Jan 1, 2006

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By R. Balia

The upper part of the "Contatto Ovest" orebody, at the San Giovanni Pb-Zn sulphur mine (Sardinia, Italy), is mined by a sublevel caving method. With increasing mining depth, a progressive caving of the hanging wall and discontinuous subsidence occurs. The orebody, which is located very close to the contact between the Cambrian limestones and the Silurian shales, strikes NE-SW for more than 100 m and dips 75-80' NW. The limestone footwall is massive and strong while the hanging-wall consists of very weak shales. The mine considered is located near a town so that the observed subsidence effects must be taken into account for both stability of the nearby railway and houses and morphological and environmental impact. A limiting equilibrium analysis to predict the progress of hanging wall failure with increasing mining depth was used. A suitable computer program was developed for solving the model by a iterative procedure. The progressive hanging wall caving and its consequent superficial effects were predicted perfectly by means of the computer program used and later confirmed by a geophysical test (seismic tomography). Our study ends with a further analysis, carried out using the same procedure, which allows to have a different geometrical situation with the presence of a pillar to protect the mill area.

Jan 1, 1990

By B Whittaker

The paper examines the role of chain pillars in longwall mining layouts as used in several countries. The application of chain pillars in relation to their expected design role is discussed. An important feature is the specification of the pillar design to meet strata loading conditions as imposed by the mining and geological setting. The paper relates longwall width and chain pillar configurations to pillar size to satisfy anticipated loading and strength expectations. Laboratory work is referred to which examines criteria for pillar stability. Comments are made regarding the application of the findings presented in the paper, to different situations involving the use of chain pillars in longwall and shortwall mining systems.

Jan 1, 1987

By Timothy Barton

The uniaxial compressive strength (UCS) is the most fundamental measurement used in geotechnical rock characterization for mine design. While there are standardized procedures for how to conduct UCS tests, there are no firm guidelines as to when to conduct them. However, it is well known that the strengths of at least some rocks can change during the time between when the core first comes up out of the hole and when it is prepared and tested in the lab. The goal of this NIOSH (National Institute for Occupational Safety and Health) study was to evaluate UCS changes occurring in a broad range of weak coal measure rocks over a one-year time span. The study found the highest moisture contents were measured when the core was fresh, immediately after it was taken from the hole. The specimens then dried rapidly over the next few weeks. Subsequently, sample moisture contents decreased slightly in the winter and increased in the summer in response to the ambient changes in humidity. The measured UCS of the core also changed during the year, apparently in response to changes in the moisture content. The UCS values from the dry, winter months were, on average, 60% higher than the values obtained when the core was fresh, and the summer UCS was approximately 11% lower than the winter UCS. These findings have implications for the use of UCS as an input parameter for both empirical and numerical mine design methods. UCS values of unprotected core tested weeks to months after drilling can be significantly stronger and indicate stronger roof sequences than warranted. In order to obtain the most representative and reliable UCS value, it is necessary to test the core, or wrap and seal it, at the drill site shortly after recovery.

Jan 1, 2008

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009