Search Documents

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By J. B. Pateiro Fernandez, S. Möllerherm, E. Drüppel

"Since 1997 the Institute of Mining Engineering 1 at the Aachen University is dealing with the concept of sustainable development in the mineral industries. During this time it has conducted several research projects in this field. Its latest project is on the development of sustainability indicators for the German mineral industry. This paper describes some results of this project. A process chain analyses have been carried out identifying economic, social and environmental effects of the minerals extraction. Thirty indicators reflecting the particular conditions in the mineral industry have been designed. One important challenge was the design of quantifiable indicators taking into account the life cycle of a mining operation as well as mineral beneficiation and enrichment of the raw material."

Jan 1, 2005

By Ernest Y. Baafi

This paper describes the results of a series of comparative studies in which polygonal, IDS, and kriging were compared for their local estimation accuracy. The specific objective of this study was to determine the impact that the particular nature of the mineralization has on the results of such comparative studies. The study was performed on simulated coal deposits and the evaluation parameter chosen was the coal thickness. For this study, many conditionally simulated deposits having different degrees of seam thickness continuity were first developed. Each simulated deposit covered an area of 30,000 ft x 30,000 ft which was, in turn, subdivided into 100 mine planning blocks of 3,000 ft x 3,000 ft in size. Thickness estimation was made for these mine planning blocks using surrounding DDH assays. In all cases tested, e.g., from a perfect continuity to a complete lack of continuity in coal seam thickness, kriging gave the best estimates among the three, followed by IDS and polygonal methods. As expected, the relative efficiency (i.e., superiority) of kriging over other estimators was highly dependent on the nature of mineralization.

Jan 1, 1982

By William R. Sharp

This paper describes a graphics station and graphics software designed specifically for use within the minerals industry. Through the graphics station, a user is able to recall maps for modification, display them on a color CRT, send the work to a plotter, and restore the work when finished. The engineer may use the system for the storing of data, per- forming engineering calculations, doing word processing, and performing general file maintenance. In addition, the system may be used to communicate with a mainframe computer for such purposes as: transmission of large data files, graphic 3-dimensional rotation of a mineral deposit or mine design, contouring of spacial data, and other data processing work.

Jan 1, 1982

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By Yuji Tsuneno, Yoshikazu Mikami, Yasuo Takeuchi

A new device was successfully developed in order to overcome the difficulty of drilling longer holes for anchors in soft soil bedrocks or swelling bedrocks, which is one of the major impediments to rapid excavation by NATM (New Austrian Tunnelling Method). With higher rotation (1200 - 1800 r.p.m.) and lower percussion energy (4 - 6 kg.m), the new drill has following advantages: (1) Applicability covers soils and medium hard rocks with the same drifter. (2) Longer hole (more than 9m) is achievable only with air flushing even in cohesive soils or rocks. (3) Better borehole stability is obtainable even in earth or in fissured rocks.

Jan 1, 1981

By K. G. Sutterer, R. J. Sweigard, U. Graham, T. C. Hopkins

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1998

By Wendell H. Nielson

Flotation processes contain disturbances which make material balance closures difficult to achieve. Lack of closure also arises from instrument errors. A portion of these problems can be overcome by proper equipment selection; the primary measurement installation and methods of initial data filtering are discussed below. The problem of data adjustment has been considered before (2). The technique described here is essentially that of Ripps (2). The technique was expanded to include linearization of non-linear material balance equations. An additional large error detection portion was also added to Ripp's formulation. Ripp's technique is based on a Lagrange-Multiplier optimization method. The Lagrange-Multiplier technique is generally applied when there are equality constraints on the variables. Steady-state material balance equations fit in this category. The basic Lagrange-Multiplier method is described. It is followed by a description of the modified material balance data adjustment technique. An example is presented to illustrate the use of this method.

Jan 1, 1970

By M. C. Rockwell, G. F. T. Lay

Promising placer gold exploration sites offshore Lunenburg County are drowned pre- and post-glacial river channels and auriferous glacial tills. Gold values up to 5.67 9/m3 have been encountered in the vicinity of the Ovens Peninsula offshore Lunenburg County. Moderate gold values associated with notable amounts of heavy minerals were reported from various other exploration sites in this area. This paper highlights the major geological and gemorphological features for placer gold depositions in southern Nova Scotia. The past to present gold exploration activities nearshore and offshore Lunenburg County are summarized and potential areas for placer gold identified.

Jan 1, 1988

By Henry Brehaut

The International Network for Acid Prevention (INAP) was formed in 1998 by 17 international mining companies to promote significant improvements in the management of sulphidic mine materials and the reduction of liability associated with acid drainage through knowledge sharing and research and development of technology. Since its inception two panels have been formed to identify and move forward with research projects and eight networks have been constituted to initiate interaction and knowledge sharing within the membership in specific areas of technical interest. An INAP web site has been developed to facilitate the sharing of information and to encourage the exchange and development of new ideas.

Jan 1, 2000

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By Ahmet Unal

Inexpensive and effective means of delivering courses to mining engineers who live at remote and scattered locations remains to be a challenging issue. Computer-based instructorless but interactive multimedia delivery is a good substitute to traditional short courses and one-way broadcasts. Such a system, enhanced with a wide area network, is an inexpensive alternative to two-way broadcasts and even to a traditional university. Course material can either be delivered on compact disks (CDs) or on-line from the host servers over the phone lines using a personal computer and a modem. Although technically not feasible using ordinary telephone service lines at the present time without further modification, advances in this field indicate that this up and coming medium may dominate the competition in the future. This paper investigates the present and the future of this technology and discusses the experiences gained in creating and disseminating a prototype multimedia CD which was created at the Rock Mechanics and Explosives Research Institute of the University of Missouri-Rolla to teach a portion of a course in Ground Control. The hardware and software used in creating the audio, 3-0 graphics, animation dips, video clips, and movies are listed. The structure of the program and the way how interactivity was achieved is explained in detail.

Jan 1, 1996

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By Andy Thompson, Frank Perrone

"As part of the Metropolitan Transportation Authority’s $10.5bn East Side Access Project in New York, 3,200 m of tunnel had to be constructed in rock, mix face and soft ground conditions beneath one of the largest passenger railroad junctions in North America, handling over 780 trains per day. The use of risk based decision making tools was essential in developing the bespoke contract framework that was adopted as well as making informed decisions once excavation commenced. This paper will outline the risk management process adopted, discuss the risks and mitigation strategies adopted and comment on the impacts of this approach on the as built Project cost and schedule. In particular, the paper will outline the unique approach used to establish the baseline against which the Contractors performance would be measured as the selection of a Slurry TBM to excavate the tunnels was considered to compromise the effective use of a Geotechnical Baseline Report. BACKGROUND AND CHALLENGES Contract CQ031, Queens bored Tunnels and Structures was awarded in September 2009 to a joint venture of Granite Northeast/Traylor Brothers/Frontier Kemper (GTF JV) for $717.6m following a negotiated procurement process. A robust approach was taken with regard to the management and payment for risks associated with the construction of these tunnels. Risk assessments were carried out during the design phase and a risk register was developed prior to procurement. During the procurement phase close attention was paid to ensuring that the allocation and pricing of known risks, together with mechanisms for managing future risks were clearly defined between the MTA and GTF JV.In comparison to the excavation work in Manhattan, which was performed in competent hard Manhattan schist, the tunnels in Queens were excavated predominantly through soft ground with a high water table and complex environmental conditions. Not only did this require the use of pressurized face TBM technology, a first in New York, but also a re-evaluation of the contractual mechanisms used to manage the hard rock excavation contracts for their appropriateness to the soft ground tunnel work."

Jan 1, 2016

By Ivan C. Machado

In full autogenous grinding (FAG Mills) the ore itself determines almost exclusively the product size that will be produced, as opposed to conventional steel-media grinding where the product size can be "engineered" by changing media size, feed size, feed rate, classifier cutpoint size, etc. SAG Mills are in the middle of the way, since they offer some room to engineer their product size by properly defining some critical process variables, such as feed size, ball charge and size, mill charge and speed. SAG Mill product P80 values are typically in the range of 500 µm (35 US mesh) to 2000 µm (10 US mesh.) Whenever it is possible to determine an optimum value for the SAG Mill product P80 value (which will be the Ball Mill fresh feed F80 value), the Engineer should define the process variables that will yield a SAG product size as close as possible to the optimum calculated P80 value. In general, a coarser SAG product will draw less power from the SAG Mill and more power from the Ball Mill, and conversely, a finer SAG product will draw more power from the SAG Mill and less power from the Ball Mill. Metal consumption analyses also have to be taken into consideration, for they typically account for 30% to 45% of the total grinding cost. This presentation addresses the issue of defining an optimum SAG Mill product size (X=P80), during the design phase of the SAG and Ball milling circuits, from a general perspective, i.e., the SAG product size that will lead to an overall SAG Mill - Ball Mill optimum performance. Bond's Third Law approach is used, as well as the SPI (SAG Power Index), and also the generally accepted equations and Engineering Practice currently utilized to design SAG Mill

Jan 1, 1999

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By Gary P. Marshall, Jeffery S. Thompson, Robert E. Jenkins

The effectiveness of the new DuPont Passivation Technology in eliminating acid generation from iron sulfides is presented. Passivation is achieved by treatment with a dilute basic perman­ganate solution. This treatment produces a thin impervious layer of iron/manganese oxide on the sulfide surface, providing a bar­rier to the environment so that the sulfide is not available for undesirable reactions such as the production of acid.

Jan 1, 1998