Search Documents

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov

As a result of thermodynamic analysis of a mineral-sodium, oleate-water system, flotation and adsorption tests at various pH values, and sodium oleate concentrations, it has been established that due to regularities of phosphate-containing minerals (fluorapatite, hydroxyapatite, carbonatapatite) flotation cannot be explained by the formation of alkali-earth metal oleates on their surface. This paper presents a novel theory that connects optimal conditions for mineral flotation with zero charge of its surface, which can explain the regularity of minerals flotation observed. The quantitative physicochemical flotation models developed based on the theory are suitable for improving industrial processes, conditioning of recycling waters, and application in automatic control systems at the plants. Key words: apatite, oleate, flotation, modeling, control, and regulation.

Jan 1, 1999

By G. I. Voiloshnikov, A. F. Panchenko, N. S. Voiloshnikova

Low world gold prices stimulate development and introduction of economically efficient ( cost saving) technology for operating gold mills. This report covers the results of testing and introduction of CIL technology to recover gold from flotation concentrate of Samarta gold concentration plant located in Buryatia (Russia). This plant is treated the ore of Zun Kholba gold deposit using gravity and flotation of gravity tails as preconcentration processes. Till recently high grade gold gravity concentrate was smelted to gold bullion and shipped to gold refinery, gravity middlings were leached by cyanidation in cone type equipment developed by Irgiredmet and flotation concentrate shipped to copper smelter. The disadvantages of flotation concentrate shipping to copper smelter are following: high concentrate transport cost; problem with gold shipped balance; high cost of flotation concentrate treatment; comparatively low gold recovery. In this connection IRGIREDMET developed the hydrometalurgical technology for gold recovery from flotation concentrate. The flowsheet was developed on the base of laboratory, pilot plant and industrial scale tests conducted by IRGIREDMET in 1987-1997 and lrgiredmet experience on CIP process testing and industrial scale introduction in Yakutia [1-6]. The flowsheet is presented in Fig.1 and consists of following base operations: concentrate regrinding;

Jan 1, 1999

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By K. Mulukhov

Introduction The depth of open-pit mines continues to increase. The typical designed depth for large quarries is now in the 300 to 600 m (1,000 to 2,000 ft) range, with some quarries even reaching depths of 700 to 800 m (2,300 to 2,600 ft). The cost of handling material from such deep mines can be 60% to 70% of the total cost. The capacity of using a cyclic means of transport, such as trucks or skip hoists, continues to drop as the depth of the mine increases. In addition to the problem of maintaining relatively low slope angles for haul roads, increases in environment pollution and increased fuel consumption make the use of trucks ineffective below 100 to 150 m (300 to 500 ft). In handling large quantities of bulky materials, i.e., more than 15 to 20 Mt/a (16 to 22 million stpy), under fixed terminal points, belt conveyors are preferable in almost in all cases. An exception is when the lump size of the load is too high for the conveyor to handle. Belt conveyors in mines can handle loads having a maximum lump size of no more than 250 to 300 mm (10 to 12 in.). The use of a movable crusher prior to the belt conveyor in an open-pit mine would make the process very expensive. Such an operation could not compete with truck haulage on a cost basis. Belt-car conveyor The main factor that restricts the lump size for conventional belt conveyors is collision impacts between the load-carrying belt and idlers. These impacts are completely eliminated in the belt-car conveyor, which was previously described by Mulukhov (1977). The unique feature of the conveyor is that the load-carrying belt is supported by moving cars. Each car consists of a troughed cross strap that supports the belt with the load and two rollers, on which the cars move along upper and lower rails. Cars are connected by two endless chains revolving over sprockets. The system uses conventional drive pulleys, tail pulleys and return idlers. There are no fasteners between the carrying belt and the car cross straps. The conveyor belt simply drives the cars along by the force of friction between the belt and the straps. A belt-car conveyor was first installed in 1970 at the Karatau mining operation in Kazakhstan. The system was an elevating conveyor with an inclination of 20° and was located on the final part of the truck haul road. The conveyor transferred blasting phosphate ore from the quarry to the crushing plant. A bunker was mounted between the trucks and the conveyor. The maximum lump size was typically 1,200 mm (48 in.). However, there were some lumps as large as 1,500mm (60 in.), which was greater than even the belt width (Fig. 1). Because the prototype belt-car conveyor was intended only for industrial trails, it had a relatively short length of about 50 m (160 ft). Nevertheless, the conveyor yielded a substantial profit over the cost of truck haulage. Naturally, the first question one might ask is why such a system is not now widely used. The reason was the further development of a huge transporting complex for the whole quarry at the base of the belt-car conveyor. After successful industrial trials from 1971 through 1973, which demonstrated the systems engineering feasibility, the State Planning Committee of the USSR included the development of the belt-car conveyor in its plan for the development of the national economy. However, mistakes were made. First, a single organization was not in charge of the development. Second, a plant that was not specialized in belt conveyors was put in charge of the design and manufacturing of the conveyor system. In addition, the crusher was installed before the stacker, which negated the major advantages of the belt-car conveyor. For loading the conveyor, a special blade feeder with pendulum suspension was developed, but it was found unreliable. The main conclusion was that, in-

Jan 1, 2003

By V. I. Ryaboy, V. A. Luknitsky, V. V. Zuyev

The action has been studied of three types of reagents used as intensifiers in grinding copper-molybdenum, sulphide-sheelite, polymetallic and other types of ores, namely N-donor, dispersant, and surface-acting agents. It has been proved that, depending on the type of ore treated, the C (N-donor) and C-170 (dispersant) reagents increase the yield of the principal size fraction of 0.074mm by 8-16% (relative). Consequently, the specific mill capacity improves by 13-21 %. The C and C-170 reagents activate the subsequent flotation stage and are thus beneficial to the mineral recovery. The surface-acting reagents affect the mineral grinding process to a lesser extent. The intensifying action of the reagents is attributed to the effective crushing energy decrease (lower crack-resistance factor) or else to the slime-dispersing effect of the reagents. The pilot-plant test results for the C reagents are given. Both C and C170 reagents are commercially produced and recommended for use at a number of concentrators in Russia, Uzbekistan and Kazakhstan.

Jan 1, 1995

By S. B. Leonov, K. I. Popov, S. B. Polonsky

The offered technological line includes a flotation pulp air conditioner operating on the impact-mechanical effect and two column apparatuses with a descending pulp-air flow mounted in series. The technology developed makes it possible to increase considerably the valuable component in the concentrate simultaneously with a reduction in energy consumption for the flotation process. The experience achieved with the technology showed the possibility for obtaining sulphide silver-bearing ore superconcentrates with the noble metal content 2-10 times higher than that in the concentrates obtained by the conventional technology. The same results were obtained in the process of calcium-bearing boron-silicate ore-dressing.

Jan 1, 1995

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By J. Michael Howard

Holes cored through the Prairie Creek lamproite volcanic complex at the Crater of Diamonds State Park by companies interested in the site's commercial diamond potential give an opportunity to redefine the size and shape of the Prairie Creek pipe. Relationships of cored rock sequences and the discovery of a previously unrecognized major rock type allow a reinterpretation of the sequence and type of intrusive activity. Trench sampling of diamondiferous rock units yielded a diamond content far below what was anticipated based on an estimate from historical records. Inadequacies of shallow bulk-testing methods for a diamondiferous pipe are examined.

Jan 1, 1999

By Boris V. Vlasenko, Vadim P. Potapov, Gennady I. Gritsko

In this paper we consider the elements of an information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated sys tem is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of changes in geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By F. Figge, T. Hahn

In this article we present Sustainable Value, a valuation methodology to assess sustainable value creation of companies. Sustainable Development posits that decisions must not only take into account economic capital but also natural and social capital. Sustainable Value, the methodology presented in this paper, borrows the idea from financial economics that the return on capital has to cover the cost of the capital. Capital costs are determined as opportunity costs, i.e. the forgone return that would have been created by an alternative investment. By expanding the well established logic of the valuation of economic capital in financial markets to also cover natural and social capital we provide a methodology that allows an assessment of the most efficient allocation of economic, natural, and social capital for sustainable value creation in companies. We demonstrate the practicability of the methodology by the valuation of the sustainability performance of British Petroleum (BP).

Jan 1, 2005

By D. J. Simbi, T. R. C. Fernandes, M. Nyamhunga

The recovery of P2O5 from a 90-95% minus 45 microns phosphate slimes sample was carried out in a 5.08-cm internal diameter and 549-cm high flotation column cell. The influence of the feed rate, feed percent (%) solids, and frother dosage on the recovery was investigated following a truncated cubic 3 level by 3 variables experimental design. Two three-variable interactions of feed rate (-l)/feed percent solids (+l)/frother dosage (-1) and feed rate (-l)/feed percent solids (-1)/ frother dosage (+I) gave the region of optimum column performance: recovery (52.60-74.50%), mass yield (15.68-18.80%), and concentrate grade (22.87-31.2196). The collector dosage also showed a significant influence on the column performance. The high reagent consumption relative to the current plant levels points to the need for the removal of ultrafine particles (<10 µm).

Jan 1, 1999

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.&apos; They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993

By A. D. Paul, Yoon R. H., C. I. Basilio

Considerable amounts of Fe3+ ions are released into solution when coal is exposed to 1-3 M acid solutions. These ions superficially oxidize the coal surface, and are reduced to Fe2+ ions. When provisions are made to generate the Fe3+ ions in solution, e.g., by inserting an anode whose potential is above the reversible potential for the Fe3+/Fe2+ couple, considerable amounts of mineral matter are liberated from the coal matrix. With many eastern U.S. bituminous coals, this mineral liberation is achieved selectively without significant breakage of the coal. It is believed that this process is induced by the osmotic pressure set-up in the crevices between the mineral matter and coal that are exposed to the solution. A theoretical model predicting the osmotic pressure is presented in this work, along with some results obtained with different coal samples.

Jan 1, 1992

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

By Michael J. Shulman

The DEAREX knowledge acquisition and engineering system is a teaching and exploration tool designed to facilitate the under- standing and development of expert systems by explorationists without the aid of a knowledge engineer and without recourse to expert system languages. To fulfill its objective, the DEAREX system considers the selection of exploration methods in desert areas. The system consists of three parts: 1. A tutorial which introduces the basic and selected advanced concepts of expert systems, 2. A sample program illustrating how an expert system works and can be used, and, most importantly, 3. A knowledge acqusition and engineering program which enables users to develop their own expert systems. The tutorial provides a brief and concise introduction to expert systems, a 10 rule exploration example which defines, explains and illustrates the basic concepts and design of expert systems, and a glossary of expert system terms including cross references. The sample program is a larger, self contained example of an expert system with some commentary illustrating addition- al expert system concepts and the role of the knowledge engineer in particularizing rules and ascertaining the knowledge base. Restricting itself to the selection of exploration methods in desert areas, the knowledge acquisition and engineering program questions the user and converts the answers into an expert system. Questions pertain to geology, infrastructure, availability of instrumentation, personnel, etc. Additional information may also included. In conclusion, some salient points concerning knowledge engineering toolkits, shells and knowledge acquisition capabilities such as contained in DEAREX are discussed.

Jan 1, 1992

By B. F. Buie

In South Carolina and Georgia an area about 20 miles wide situated near the inner margin of the Coastal Plain and extending from the vicinity of Columbia, S.C. southwestward about 180 miles to the vicinity of Macon, Georgia is the principal kaolin-producing area of the world. It is especially important as the world&apos;s major source of clay used for paper coating. Essentially all of the land known or likely to be productive of quality kaolin in this area is now owned or controlled by producing companies. The least-fully developed portion is that in the vicinity of Wrens, Georgia which has been explored and developed since 1961. For the two decades following the end of world war II, demand for kaolin increased at approximately twice the rate for other industrial minerals. From 1945 to 1965 production increased four-fold. Since 1965 the rate of increase has been less, but the outlook now is that production and demand will double at least once again before the year 2000. A substantial part of this increased demand has come, and will continue to come, from industrial development, especially in the paper industry, outside the United States. The general effect, in addition to a continuing increase in production in the U.S., will be to cause: 1. Intensive research for development of more effective and more economical methods of beneficiation; 2. Concerted research effort to find an economical way of modifying high-viscosity kaolin so that it can be used for paper coating; 3. More active exploration in the U.S. and overseas, especially for deposits to supply the foreign markets; 4. More intensive study of the geological factors responsible for the accumulation of commercial deposits of kaolin; 5. Some modest rise in price, relative to the cost of other industrial minerals. The effect on kaolin producing region of Georgia and South Carolina will be to cause: 1. Working of progressively lower-grade deposits; 2. An increase in the acceptable thickness of overburden; 3. Mining of deposits farther down-dip, the use of which is now inhibited by large volumes of groundwater; 4. Increased threat of invasion of the kaolin in industry&apos;s market by substitute materials; 5. A substantial increase in concern over environmental factors; 6. More attention to be paid to the large opportunity offered for mining of silica sand and other co-products.

Jan 1, 1972

By F. L. Wilke

Truck haulage costs form a major part of the total mining costs in hard rock open pit, mining operations. In order to minimize these costs one has to - determine the optimal truck fleet (type, size and number of trucks), and. simultaneously - determine the optimal organization of running the haulage system, i.e. especially select the optimal dispatching strategy in order to ensure maximal utilization of the trucks, and simultaneously - establish a reliable maintenance and servicing system to guarantee maximal availability.

Jan 1, 1982

By N. I. Aziz, B. Srinivasa Rao, R. N. Singh

The control of respirable dust and its subsequent exposure to miners is essential for improved safety in longwall mining. The extensive variation in face conditions and operations of longwall make numerical modelling an attractive approach in both the development and evaluation of dust control devices. Three dimensional finite element computational fluid dynamics code FIDAP was used to model air velocities and the effect of dust control techniques on dust concentrations at a typical longwall face. The effect of shearer body on airflow characteristics in a longwall face was analysed with both antitropal and homotropal ventilation systems. Path traces of particles introduced near the shearer drums was also simulated. Initial modelling results were validated using field trial results at three operating longwall faces. Results of simulations tallied very well with the field results.

Jan 1, 1993

By Kenneth P. Katen

Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped [ ] that the information presented in this chapter will enable the reader to better understand the two mechanical systems and the mining concepts involved in their employment.

Jan 1, 1981

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel&apos;s average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988