Search Documents

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

By A. A. Peshkov, N. A. Matsko, K. N. Trubetskoy

It is possible to divide the general objectives of a company into two components: maximum expected profits and viability over time. These components are designed to maximize the companies value over time. The evaluation of a project includes both a discounted cash flow (DCF) analysis and a risk analysis. The DCF analysis determines whether the project should be accepted or rejected, and the risk analysis helps to forecast possible deviations from the original estimates. However, the results of both methods do not allow for a quantitative comparison between the main objectives of the venture, and they do not resolve the issue of whether it is advisable to sacrifice immediate profits for future profits. This paper attempts to resolve this issue. The present research was carried out on mining projects with different waste-extraction schedules. Calculations were made using the US Bureau of Mines' usage-of-costs model. Russian experience in open-pit mining is reflected in this paper.

Jan 1, 1996

By E. M. Haynsworth

The disposal of phosphatic clays has presented a problem to the phosphate industry since the mining of phosphate rock first began. As the flotation process was introduced in the late 1920's, the problem of clay disposal was increased significantly since clay is present in proportionally greater quantities in reserves yielding flotation concentrates. Because of their physical character and the tremendous surface area per unit volume, these clays have the characteristic of retaining large volumes of water as they are slurried during processing. The phosphatic clays with which we are dealing consist primarily of apatite, wavellite and montmorillonite. In the beneficiation process, we remove the -150 mesh material as waste. However, the particles are essentially smaller than -325 mesh, and more than 70% are smaller than three microns. The disposal of clay and the recovery of a portion of the water require settling areas with a capacity ranging up to 2 cubic feet for each cubic foot of phosphate matrix mined. According to a recent study by the Bureau of Mines, the average cost for disposal of these wastes is 24.5 cents per ton of, product (U. S. Bureau of Mines Circular 8404). This is a major cost of phosphate rock production.

Jan 1, 1970

By Peter I. Brooker

The semi-variogram, the basic tool of geostatistical estimation procedures, must itself be estimated from the available data. From a numerically simulated two dimensional deposit, with known variability expressed through its semi-variogram, the standard arithmetic mean estimator is used to calculate experimental semi-variograms. These are determined on a series of data sets obtained from the deposit with various sampling grids which cover different areas of the deposit and which have a wide range of available data. The orders of discrepancies between estimated and theoretical semi-variograms are determined in this idealized situation; and this provides a basis against which to assess experimental semi- variograms made on field data.

Jan 1, 1982

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today's market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By D. Royston

Curved pulp lifters can provide improved discharge performance from SAG mills, especially for the coarser fraction of rocks in the discharge. They also can provide improved wear life of the pulp lifter, especially the base of the pulp lifter and diversion cone, over comparable straight radial pulp lifters. Current experience with curved pulp lifters and associated grates is covered including design issues and discharge performance for both the slurry and rock components of the discharge.

Jan 1, 2003

By I. H. Gundiler

A pilot-plant flotation concentrate containing 21.6 g/t gold and 2 kg/t silver was used for this study. Base-line cyanide and thiourea tests showed 30-40% extraction of both gold and silver. After roasting (450-750C), the maximum gold extracted was 89% with thiourea and 76% with cyanide. Pressure oxidation tests were conducted following a statistical experimental design in a 2L laboratory autoclave at 10% pulp density, and the residues were subsequently leached in acidic thiourea solutions for 2h. Leach results were presented in the form of contour maps, and optimum autoclave conditions were determined for maximum gold extraction (93%). However, silver extraction was only 7% when gold extraction was maximized.

Jan 1, 1992

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By T. V. Durkin

Approximately 1,390 t (44.7 million ounces) of gold have been produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection by promoting mining as an industry while requiring prevention of pollution and reclamation of affected lands to a beneficial use. The mining laws have evolved since their inception in 1971, especially in response to gold mining. The laws have remained flexible to meet changing regulatory needs. Gold production has continued relatively unabated, even in the face of public scrutiny, two mining moratoriums, and isolated environmental problems. The department's system of "one-stop-shopping" for environmental permits streamlines the permit process, fosters quick resolutions to compliance problems, and helps keep enforcement actions out of the courts. Specific case histories at heap leach mines within the Black Hills are presented.

Jan 1, 1998

By J. W. Merks

Spreadsheet software is used to convert test results for drill core samples into borehole statistics such as volumes and masses of in-situ ore, metal contents and variances of metal contents. The properties of variances and the sampling variogram play a pivotal role, The additive of property of variances gives a sound scientific basis to the calculation of confidence limits for metal contents and grades as a measure of the risks associated with estimating reserves and resources.

Jan 1, 2000

By Phillip R. Moyle

Voluminous deposits of commercial-grade phosphate occur in sedimentary strata in a 350,000 km2 (135,000 mi2) area of the middle Rocky Mountains of North America known as the Western Phosphate Field. The Permian marine strata that host the phosphate were deposited on the western margin of the North American craton and subsequently deformed, first by folding and thrust faulting of the Laramide orogeny, and then by Cenozoic Basin and Range block faulting. Carbonate fluorapatite is the primary phosphorus-bearing mineral. Organic matter is abundant in some strata, and both biogenic and non-biogenic pyrite are also present. Certain strata are enriched in several trace elements, especially in arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), selenium (Se), vanadium (V), uranium (U), and zinc (Zn). Phosphate has been mined from the Western Phosphate Field for nearly 100 years. Phosphate mining and processing constitutes the largest mineral industry of Idaho, producing more than $600 million in processed mineral value in 1997. Resource management agencies, phosphate producers, and others are concerned about the release of Se from phosphate mine wastes, especially at Maybe Canyon, and the potential effects that Se and other trace elements may have on the environment and on human health. U.S. Geological Survey (USGS) Mineral Resources Team scientists initiated a multidisciplinary study of the Permian Phosphoria Formation and related rocks in the south- eastern Idaho sector of the Western Phosphate Field in response to a request by the U.S. Bureau of Land Management (BLM). Studies to date reveal that Se is present in several phases, including native Se, and in an as yet unidentified form, possibly an organo-Se compound. Selenium is also present in pyrite and sphalerite. Selenium concentrations range from 1.2 to greater than 1,000 parts per million (ppm) in samples collected from exposures of the Meade Peak Phosphatic Shale Member of the Phosphoria Formation (Meade Peake) at Enoch Valley. The results suggest that Se concentrations vary spatially across strata and with depth, perhaps comparable to spatial variations of phosphate and organic carbon concentrations throughout the Western Phosphate Field demonstrated in previous studies. Some Se-enriched strata may be of adequate dimension to allow selective extraction during mining. Such units could be handled separately from the main ore process or waste streams and isolated in order to reduce the potential for release of Se to the environment

Jan 1, 2001

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By George D. Roberts

Dams are constructed to retard the flow of water or debris; therefore natural forces are constantly at work to remove such obstructions. To circumvent nature and avoid expensive trouble with a dam requires thoughtful far-sighted planning, careful construction control and vigilant periodic inspections to detect and repair deterioration at its inception. Although the factuality of the foregoing statements is apparent, all too many have failed to consider them in the past as will many in the future. "The economic, but safe construction of dams calls for the highest order of technical knowledge, practical experience and sound judgment." (1)

Jan 1, 1967

By Peter I. Brooker

The turning bands method for the simulation of spatially correlated data in two or three dimensions requires that the relation- ship between the covariance obeyed by the realizations first generated on lines, and the covariance of the two or three dimensional process must be solved. In three dimensions the solution is immediate, but in two dimensions the integral equation relating the covariances of the one and two dimensional processes is more complex. This is solved in this paper and is applied to the most common model used in ore deposit description, the spherical covariance.

Jan 1, 1984

By Richard S. Ghent, Daniel G. Warnock

JOHN HAMRIC: Our next speakers are Richard Ghent, manager of environmental health and safety for CF Industries, Hardee Phosphate Complex, in Wauchula, Florida. Richard has 20 years' experience with environmental health and safety affairs. He has a bachelor of science degree from the University of South Carolina. With him is Daniel Warnock, who is supervisor of safety and training also at the Hardee Phosphate Complex. Daniel's experience is in safety programs and electrical training. Their presentation is "Regulations Versus Management Practice." RICHARD GHENT: Written procedures give structure to safety programs. At their best, they are brief and understandable to facility personnel and clearly identify roles and responsibilities. At worst, they attempt to recite the entire regulation they are intended to address. Some regulations, such as OHSA's Hazard Communication Standard, require employers to develop, implement, and maintain a written program. As written programs and procedures are developed, some basic questions arise: Is the program designed to achieve compliance with regulatory requirements or does management expect the program to go beyond compliance to some higher level of performance? Management may have difficulty in measuring and communicating performance expectations in safety. A facility with 4 million safe work hours does not suddenly become unsafe the day their safety record is broken. Generally, management expects safety programs to meet regulatory requirements and to protect the employer from enforcement actions and fines from regulatory agencies. Management also expects that safety programs will result in a safer work environment with fewer incidents, accidents, and near misses. But it is difficult to know when a safety program has succeeded. If the program is expected to go beyond compliance, what other standards should be included (e.g., ANSI standards, company management practices, lessons learned from inspections and audits, recommendations from safety committees, etc.) in the

Jan 1, 1998

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986