Search Documents

By David F. Becker

Two-dimensional, finite-difference elastic modeling aids in planning an optimum seismic-acquisition scheme to define the extent of subsurface cavities resulting from in situ gasification. To understand the seismic effects of a cavity, two models are compared and contrasted. Model A consists of a low-velocity layer (LVL) in a half space; Model B contains a rectangular water-filled cavity in the LVL. Amplitude differences are the dominant effect on the surface records for each model. Cavity resonance and diffraction effects are more definitive in vertical seismic profiles (VSP's) and in a "snapshot" of the wave field. Interpretation and subtraction of corresponding records for both models shows the need for pre- and post-gasification seismic recording. Also VSP data are more informative than surface records.

Jan 1, 1983

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By Angus Maxwell, Jacob Grasmick

As the tunneling industry continues to adopt Tunnel 4.0, digital twins of the tunnel construction site are becoming standard requirements for tunneling projects. However, the benefits of these remain unproven to many practitioners. The paper discusses the various implementations of digitalization and describes efforts to combine all data types to analyze the relationships between influences, predictions and performance in a single digital platform. This includes data pertaining to investigations, design, construction, monitoring and post-construction asset performance and management. Based on 16 years of global tunneling projects the paper aims to quantify the tangible and intangible benefits of such systems. Using a number of real examples, the paper describes where opportunities were taken and where they went unrealized. Challenges and considerations for both procuring and developing these digital twins are also discussed.

Jun 13, 2021

By Argenis Gamboa

The Arab community is formed by around twenty countries in Africa and Asia, linked basically by a common language-Arabic - and the same religion, the muslim. They jointly occupy around 12 million square kilometers with a total population of around 140 million people. Nevertheless, these nations differ widely in their geographic area and population. Thus, while Egypt has a territory of over a million square kilometers and a population of nearly 40 million people, Kuwait, Qatar and Bahrain have, among the three of them, less than 30, 000 square kilometers and a million inhabitants. The per capita income also vary greatly, depending on whether they are oil producing countries or not. Generally speaking, it can be said that these countries economies have been based on oil or agriculture and that in these last years, they have been making serious efforts to increase their degree of industrialization and have greatly improved their infrastructure. This trend has resulted in the development of the iron and steel industry, which is still in a stage of primary development.

Jan 1, 1979

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By Rudolf E. Greuer

Modeling a mine ventilation system is a formidable mathematical problem requiring the solution of twice as many equations as there are airways with half of these being quadratic equations. The addition of a mine fire to the problem adds many more complexities. The U.S. Bureau of Mines and Michigan Technological University attacked this problem in stages. During the 1970's and 80's, a series of computer simulation programs were developed which offered progressively increasing levels of modeling capability and accuracy. The current version of this software, MFIRE 2.0, was released in 1993. This programs provides for full dynamic state mass flow-based modeling of a mine ventilation system, and includes natural ventilation, mechanical ventilation, air reversals and recirculation, methane and fire contaminant spread, and moisture condensation and evaporation in the mass flow and heat exchange calculations. This program is a useful tool for routine ventilation planning and can significantly improve mine safety by enabling detailed quantitative analysis for mine emergency preplanning. This paper reviews the evolution of the MFIRE program from its infancy as a simple digital network simulator replacing analog computers to the present version.

Jan 1, 1994

By J. A. Lombardi

Innovative hard rock narrow-vein, longwall, and stope leach mining systems concepts are described and evaluated economically. The principal tool proposed for use in these systems for both mine development and production is the U.S. Bureau of Mines radial-axial splitter. The mining systems concepts are prefeasibility level costed and projected to be cost competitive for steeply dipping veins, 0.6-1.2 m wide, for horizontal tabular ores 2 m -5 m thick, and for leachable ores with greater than a 1.7:1 stripping ratio. In all of the systems the orebody, less swell, is retained underground for use as backfill.

Jan 1, 1994

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By J. C. Weimer

The goal of Bethlehem's mining research program is to improve both the safety and productivity of our mines through the use of new equipment, new technology and new mining methods. Although we can all agree on the value of such goals, achieving them can be a costly, time-consuming and sometimes frustrating experience. However, the potential benefits of lower costs per ton and better safety in an increasingly more stringent and confusing regulatory environment make the expended effort worthwhile. At Bethlehem we feel that the mining companies are in the best position to determine the needs of the industry, and coal companies have the incentive as well as mine sites at their disposal for testing. Therefore, the mining industry should be leading the research effort

Jan 1, 1979

By J. W. Lowry

After years of processing copper porphry ores, the Ray concentrator of Kennecott Minerals Company installed a concentrate regrind mill in its flotation circuit. The first cleaner concentrate is reground rather than the usual rougher concentrate. An additional cleaning of the reground product yields an increase in copper content of the final concentrate and a significantly lower insol content. The desired goal of decreasing the energy requirements for smelting the concentrate has been achieved.

Jan 1, 1980

By Ronald L. Wiegel

Success has been achieved in developing mathematical models of rod mills, ball mills and recently to a limited extent autogenous grinding mills. There is also considerable activity in the development of mathematical models of various mineral concentration opera¬tions, such as flotation, magnetic separation and electrostatic concentration. However, at present there is a technological gap which hinders the integration of both size reduction and mineral concentration models into an overall process simulation model. This gap exists because size reduction models have been aimed at describing the size of the product and have not dealt with the equally important problem of identifying the product composition in each size fraction. Without this information the concentration model is ineffective. This situation is especially critical in the simulation of the magnetite-taconite beneficiation process, where a portion of the ore is rejected from the process following each stage of size reduction. Consideration has therefore been given to the merging of a size reduction model and a mineral liberation model to permit prediction of mineral composition as a function of size. The results of this integration of size reduction and mineral liberation models are discussed from both theoretical and practical viewpoints using batch grinding data for a magnetite iron formation sample as a demonstration vehicle.

Jan 1, 1975

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986

By F. Milton Lewis

In 1977 a paper was presented which reviewed the cost trends in producing copper by conventional processes for five years, 1972 through 1976. In this paper these costs have been updated to include the years 1977 and 1978.

Jan 1, 1979

By Kadri Dagdelen, Thys B. Johnson, Salih Ramazan

Long-term production scheduling design is a very important part of mining because it determines the economic outcome of a project There have been many attempts to solve the optimum pit scheduling problem, but there has been no success in developing a scheduling method to give optimum results in maximizing net present value of a mining project. Open pit production scheduling problem can be formulated as a mathematical programming problem and solved using Mixed Integer Programming technique. However, it is not possible to solve the formulation within a reasonable time since the number of integer variables required for the mathematical model is too great to do that by today's available computer technology. There- fore, a methodology is required to combine, or aggregate, the mining blocks and to decrease the number of integer variables in scheduling without losing the optimality. Therefore, the fundamental tree concept was developed in this paper to combine the blocks. A fundamental tree is defined as any combination of blocks such that: 1. the blocks can be profitably mined, 2. the blocks obey the slope constraints and, 3. there is no subset of the chosen blocks that meets 1 and 2. A Linear Programming (LP) formulation is developed as a mathematical model to find a set of fundamental trees that exist for a deposit. Since the blocks are combined to form the fundamental trees, the number of variables required for the scheduling model is decreased significantly. This decrease in the number of variables makes it possible to mathematically formulate the multi-time period scheduling problem as a Mixed Integer Programming (MIP) model. A case study is performed on a multi-mineral copper deposit in Peru, South America. NPVs of annual after-tax cash flows generated based on the schedule provided by the "Fundamental Tree Algorithm" is compared with NPVs resulted from the schedules coming from three of the computer packages presently available to the mining industry. These are Mintec's M821V, Earth- work's NPV Scheduler, and Whittle's Milava open pit mine schedulers.

Jan 1, 2002

By David D. Eyer

In today's world coal market, coal quality is becoming increasingly important. Often the coal quality parameters are one of the crucial considerations in the development of a coal mine. Because of the user's tighter specifications and because of strict environmental regulations, coal producers are being called on to predict with increasing accuracy, not only the quality of their product but also the variability of that quality. This area of reserve evaluation is naturally receiving a great deal of scrutiny. Consolidation Coal Company has developed reliable and sophisticated methods for predicting coal quality, but the company's efforts continue to search for even better techniques. The following is a step-wise summary of The methods currently used by consolidation coal company, with A recent project used as an example. Two of the newer, and as yet experimental techniques will be briefly discussed.

Jan 1, 1980

By Sheldon P. Wimpfen

Forecasting, an ancient art, is con-ducted by everyone in varying degrees. It is a vital aspect of mineral production and conditions must be predicted over a long time frame in all aspects of the industry from exploration to plant construction. Although many government agencies as well as private industry make forecasts, there are insufficent "make good" analyses performed. The performance of more such studies could sharpen forecasting ability.

Jan 1, 1983

By B. Mishra, Q. Shi, Y. Zhao, G. Zhao

Shale is anisotropic due to the presence of bedding planes. The anisotropic strength of shale has been extensively studied. However, little attention has been paid to the size effect on shale strength considering the anisotropy. This research uses the discrete element method to study the size effect on the strength of shale under the uniaxial stress state. It is assumed that the anisotropy is caused by bedding planes, while the size effect is caused by randomly distributed flaws. The numerical model of shale comprises three components: shale matrix modeled by bonded particles (2) bedding planes modeled by smooth joints (3) flaws modeled by discrete fractures. The developed model is scaled to different sizes and tested in the uniaxial compression and the direct tension tests. The test result show that the uniaxial compressive strength decreases as the specimen size increases when the loading direction is perpendicular or parallel to bedding planes. The uniaxial compressive strength is determined by the flaws while the bedding planes only play a limited role. However, the size effect on the direct tensile strength depends on the direction of bedding planes. When the loading is perpendicular to bedding planes, the size effect is not prominent. The direct tensile strength is determined by the bedding planes while the flaws have little effect. When the loading direction is parallel to bedding planes, the direct tensile strength decreases when the specimen size increases. The direct tensile strength is determined by the flaws while the bedding planes have little effect.

Mar 2, 2022