Search Documents

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1982

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

By Daniel Hodouin, Claude Bazin, Sami Makni

SCOTT COULTER: Thanks, Eric. Thank you all for coming. Our first speaker today is Claude Bazin. Claude received a degree in metallurgical engineering in 1980 from Laval University in Quebec. He worked for a short time in a mineral processing plant and then returned to Laval to complete graduate studies in the field of process modeling and control. He obtained his master's degree in 1983 and his Ph.D. in 1990. In 1987 he joined Brunswick Mining, New Brunswick, as research metallurgist and subsequently process control engineer. In 1990 he joined Helzfield Mines, New Brunswick, as senior metallurgist. In 1991 he accepted a position of professor at the department of mining and metallurgy at Laval University, a position he is still holding. He's a member of the CIM, TMS, and the Society for Mining, Metallurgy, and Exploration. Claude's topic today is "On-Line Material Balance for Flotation Plants." INTRODUCTION CLAUDE BAZIN: During the last two decades, the on-stream analyzer (OSA) has gained the stat& of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant (Leroux and Franklin 1994), and its application to oxide mineral flotation plants is increasing. The OSA assays are sent to the flotation operators via an operator console or to control loops of various degrees of complexity (McKee 1991) implemented in a distributed control system (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one could ask, "Could we get more from the OSA?" Some plants reported the use of OSA measurements for process optimization (McKee 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2-product formula (Wills 1992, p. 124). The 2-product formula is sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al. 1993). Least squares algorithms provide a robust alternative to filter out measurement errors (Spring 1992). This paper presents some applications of a recursive least squares algorithm that provides real-time estimates of the mass flow rates within a flotation plant using OSA and mass flow rate measurements.

Jan 1, 1998

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By C. I. Basilio

Pearson's hard and soft acid and base (HSAB) principle may be applied to flotation systems. The HSAB principle states that hard acids prefer to bond with hard bases and soft acids prefer to bond with soft bases. By determining the Drago E and C parameters for the different components of a flotation system, the HSAB principle could be used to explain the selectivity of some collectors such as thionocarbamates against some minerals. Determination of these parameters is done by utilizing Drago's theory and flow micro-calorimetry.

Jan 1, 1991

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By A. E. Aldrich

The Pittsburg & Midway Coal Mining Co. (P&M) is expanding a combination of surface and underground coal mining operation in Northeastern New Mexico. The York Canyon Complex, located 35 miles west of Raton, New Mexico, is aggressively pre-paring for increased production while meeting present requirements. Surface mining activities in four separate mining areas are preparing the complex for additional markets. Drag-line, truck/shovel, highwall miner and contour stripping are surface mining methods currently planned. In addition, P&M will move a Marion 8200 dragline from Kansas to the York Canyon site, finish constructing a $20 million coal preparation plant, and complete conveyor upgrades to the existing underground mine. This paper will describe the diverse York Canyon Complex.

Jan 1, 1993

By P. W. Finck

Detailed mapping, using a large diameter diamond-drill in conjunction with high resolution reflection seismics, has increased known resources of kaolin clay and glass-grade silica sand from scattered deposits generally < 1 km2 to large areas of Cretaceous valley fill up to 130 m thick. Detailed chemical and physical analysis of drill core is presently underway. Silica sand deposits intersected in this study are up to 99.4 % SiO2 without beneficiation. Light grey to white kaolin clays identified by XRD and DT A have concentrations values (without beneficiation) up to 47.28% SiO2, 37.44% Al2O3, 0.45% Fe2O3, 0.49% K2O, 0.07% Nap, 0.07% CaO and 0.39% MgO.

Jan 1, 1996

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

By Carl D. Wood

Traditionally, when one considers the optimization of a flotation circuit, the scope of work focuses on a review of unit process equipment. This usually includes topics such as grinding ball typed, grind size, classifier efficiency, mill liner design, chemical reagent addition rates, alternative chemical reagents, on-line process analysis, and automated control strategy. However, since very few companies can afford the capital expenditure needed to completely automate the processes, the flotation operator remains as a critical link in optimization of the circuit. Therefore, upgrading of operator skills and knowledge through training must be considered as equally as important as unit process review. This paper will review some concepts and approaches to innovative operator training. INTRODUCTION Consider for a moment the fantastic changes that have occurred in process automation at many flotation plants during the last several years. Flowmeters, density gages, and on-stream analyzers now routinely measure process conditions and effect control strategy. These functions had until recently been entrusted to human flotation operators. Now with a little stretching of the imagination it is possible to envision a plant where very little human intervention would be required. However, when one begins to calculate the capital cost required to fully install automatic equipment, it quickly becomes apparent that many parts of flotation plants will continue to require skilled, knowledgeable operators to ensure successful operation. Additionally as these automatic systems are put into place, the operator&apos;s duties become increasingly complex. Therefore no flotation plant can be considered optimized without upgrading each operator&apos;s skill and knowledge to match the technology utilized. BACKGROUND At Henderson, one of the hardest steps towards the optimization of operators was to realize that present level of operator skill and knowledge was not sufficient. Since Henderson had a track record of producing the highest quality molybdenum concentrate in the world, it was difficult to accept the idea that change was needed, or even possible. This realization came about as Henderson began a program to modernize the cleaner plant circuit. Henderson utilizes a complex cleaner flotation circuit involving multiple stages of flotation, with a counter- current routing of flotation tailings. Since start-up in 1976 Henderson had relied upon next-day laboratory analysis techniques, that provided an after the fact measurement of process. Hour to hour process control was implemented by the operator, the basis for the operators&apos; control decisions was primarily the individual operator&apos;s experience and "feel&apos;. Bench marking of current flotation technology indicated that on-stream analysis was a proven state-of-the-art method for improving process control. An Outokumpu Courier 30 analyzer was purchased and installed to provide real-time analysis of critical cleaner plant flows. The analyzer quickly began to provide valuable assay information, allowing the metallurgists to develop specific target values for important flotation variables. However due to the complexity of the circuit, the analyzer information showed that a problem was usually caused when several targeted parameters went out of range simultaneously. This made it difficult for the operator to determine just where to implement the proper corrective action. It became apparent that to take full advantage of the new analyzer information each operator would have to become proficient at understanding the material balance of the entire circuit. TRAINING PLAN CONCEPTS With the goal of giving each operator a working knowledge of a circuit material balance the following concepts were applied to develop a training plan: - Most operators were high school graduates, but had fairly weak mathematical skills, and had very little experience at metallurgical calculations. - The training would have to address a wide range of topics from basic fundamentals to complex material balance. The basic sequence decided upon, was to present a fundamental topic to the entire group, break into small groups to work a “hands on&apos;”case study example of that topic, and design the case study results so that they could be combined to highlight a major portion of the material balance concept.

Jan 1, 1993

By Lars A. Stålberg

"This paper will touch several of the topics covered by SDIMI 2005, including,• Sustainability indicators for the minerals industry, • Best practice of sustainable development in the minerals industry, • Social contributions,The complex issues of a company’s "sphere of influence" and "complicity" are important to every discussion of business and Human Rights. The paper will argue that to protect and promote Human Rights needs to be regarded as an integral part of sustainable development policies for the minerals industry. This implies a need for explicit inclusion of Human Rights indicators among the indicators to be applied by the minerals industry."

Jan 1, 2005

By Stanislatv Pawlowski

New, large sulphur deposits were discovered in Poland in 1953, the result of investigations by the National Geological Institute. All deposits occur in a widespread Miocene evaporite unit in the Carpathian foredeep. The gypsum underlying impermeable Sarmatian clays was altered to limestone and native sulphur where penetrated by hydrocarbons and bacteria. All deposits occur in Miocene structural uplifts. The early determination of the genesis of the sulphur deposits and their occurrence in elevated blocks led to an exploration program that successfully located new deposits.

Jan 1, 1978

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960&apos;s. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By Y. J. Zhang

This paper presents the results of a recent study on the development of an in-situ testing method for determining the coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using the penetrometer. It is a hydraulically powered device that uses an indenter to press the surface of the borehole until the load reaches the failure point of coal. The pressure and the penetration of the loading pin are recorded by the data acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of pillar strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1995

By D. J. Benton, S. Finley, D. T. Orr, A. J. Chambers, M. A. Stepan

"Corrosion of ground support can lead to falls of ground that pose a significant risk to miner safety. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is investigating corrosion at the Hecla Mining Company’s Greens Creek Mine, located near Juneau, Alaska, USA. Field studies have used photogrammetry surveys to document welded-wire mesh corrosion, and laboratory studies at NIOSH’s Spokane Mining Research Division (SMRD) have investigated the effects of corrosion on ground support integrity. Findings show that (1) corrosion monitoring through photogrammetric methods may be effective for qualitative measurements of welded-wire mesh corrosion, and (2) there is a relationship between loss of load-bearing capacity and the diameter loss due to corrosion in welded-wire mesh. Photogrammetry results thus far have measured an apparent bulking of the corroded welded-wire mesh, and preliminary laboratory tests have investigated the relationship between the larger bulked and effective wire diameter. If this relationship is verified, these results may indicate that photogrammetry, when combined with the models produced in laboratory tests, could offer a means of monitoring corrosion levels, as well as rock rib deformation. INTRODUCTION Reducing the number of rock fall injuries and fatalities is an important part of the mission of the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD). Ground control using support systems to protect miners from rock falls is one of the oldest mining sciences, and considerable research has led to a variety of modern tools and methods in use today. Among these tools are rock bolts and welded-wire mesh, which are made from increasingly higher-strength steel grades to meet the increasingly demanding requirements of underground mines [1]. However, the benefits of these higher-quality support elements may be negated in corrosive mining environments. A better understanding of how corrosion affects the support capacity of ground support systems will assist engineers in determining when an opening is at a greater risk of falls of ground. Accelerated corrosion has been occurring in some areas of the Hecla Mining Company’s Greens Creek Mine near Juneau, Alaska, USA. Corrosion of ground support has resulted in two falls of ground occurring between April 2015 and March 2016. While these falls of ground did not injure any personnel, mine management recognized the high risk to miner safety and responded by actively undertaking a ground support rehabilitation program. Rehabilitation measures include the installation of both galvanized and coated, corrosion-resistant bolts and welded-wire mesh, depending on local conditions."

Jan 1, 2017