Search Documents

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By E. C. Speers

The Ray Mines Division has a long and illustrious history beginning in 1911, as one of the early underground block caving copper mining operations. The tonnage mined from the beginning of operations, increased from about 8, 000 TPD in the early years to the present daily tonnage of 22, 500 tons, mined by open pit methods. The Ray basic milling practice has been relatively unchanged since 1927 when the sulphide-flotation process was introduced at Ray. The leach-precipitation-flotation process introduced in 1956 has been the only major process change. The change from underground to open pit' mining was accompanied by a renewed drilling and exploration program which developed large tonnages of low grade copper ores both in the porphyry and the diabase. The ore bodies as outlined were of such a grade and size that it soon became apparent that economical operations could not be developed with the lower tonnage rate. Also that in order to develop these newly proven ores, it would be necessary to move the Ray crushing plant, the Ray. supporting shops, offices, a substantial part of the Ray townsite, and would also involve the rerouting of Mineral Creek, a typical Arizona stream which is dry most of the year but can flow as high, as 8, 000 second feet in the rainy season. This paper describes those changes in flow sheet made necessary both by the increased tonnage .and the requirement to move as much of the crushing facilities from the Ray area as practical in order to free the mine for the extension of its physical limits.

Jan 1, 1961

By Norman Weiss

The design of an ore-processing plant requires a high degree of cooperation among the geological, mining and metallurgical engineers. The purposes of this section are to provide mill design information most commonly needed by the mine planners and management, and to summarize the kinds of information that must be supplied to the mill designer to enable him to provide a suitable plant. 28.1-BASIS OF DESIGN NORMAN WEISS 28.1.1-SIZE OF PROJECT The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect, a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd without major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding and processing. Hours per shift also are an important factor in design, particularly in the case of ore delivery, and the percentage lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into account. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure. but rather as an average over a calculable period, such as 10 yr, or as a specific daily capacity over the first 2 yr, next 4 yr, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 mi southwest of Tucson, Ariz., described by Weiss and Vincent.' where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. 28.1.2-EXPECTED LIFE The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis which, in turn, is based on many factors.' From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, and many others. Costly installations that may be excellent investments for a 20-yr project may be wasteful for a 5-yr operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grinding-the former may be found more economical for a 5-yr operation, and the other, more costly, method more economical for a 15 to 20-vi- life.

Jan 1, 1973

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By George W. Parker

The ever increasing costs of labor and supplies have made it imperative that operators of open pits look for some way in which to cope with these increases. One of the most logical ways to increase the efficiency of an operation is by the introduction of larger haulage equipment, as generally haulage costs are the greater portion of the over all expenses. These larger haulage units require larger shovel units. In the late 1930's and the early 1940's large mining, quarrying and heavy construction operations had more or less standardized on the 4 to 6 cubic yard shovels. During this same period the haulage units were generally 22 to 27 tons. Some ten years ago 9 - 13 cubic yard shovels along with plus 50 ton haulage units were introduced by manufacturers in an effort to enable operators to decrease costs.

Jan 1, 1962

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By Hitch M.

Many mining wastes, especially those from the metal mining industry, have traditionally been treated as a matter of little or no value and in practice a cost burden. Some wastes, due to their reactivity characteristics, have emergent values that go beyond purely economic and into the environmentally beneficial realm. This paper discusses the changing paradigm of mine waste management. Such fundamental parameters such as cut off grade, and strip ratio, are positively impacted by the revaluation of waste rock material. Mine rock waste can now be seen as a commodity of value, similar to the underlying ore being mined and influences the economic performance of suitable projects. This valuable material can be used for industrial purposes including acid neutralization as well as the capture and long-term disposal of anthropogenic carbon dioxide. The Turnagain Nickel project, located in northern British Columbia serves as an example of how waste rock material can become an important matrix for carbon capture and sequestration and can benefit economically from it. By producing material that has emergent economic value as well as carbon capture and sequestration capabilities, the sequestration matrix producer is a beneficiary of new carbon credits that have a market value and is looked upon favourably by regulatory authorities and affected stakeholders.

Jan 1, 2010

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By R. Callaway

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (?CERCLA?), as amended by the Superfund Amendments and Reauthorization Act of 1986 ("SARA?) establishes a comprehensive Federal regulatory program for addressing environmental and public health risks posed by releases of hazardous substances into the environment from a wide variety of industrial and other sources. The statute is primarily administered by the United States Environmental Protection Agency ("EPA"). The applicability of CERCLA to the mining, milling, and smelting industries (hereinafter referred to as the ?mining industry?) has been upheld by the courts and recently affirmed by Congress. The purpose of this article is to briefly outline the scope of CERCLA as it applies to the mining industry, the scope of EPA's activities pertaining to the mining industry under CERCLA, the types of remedies which may be pursued by EPA, and the liability scheme of CERCLA as it applies to corporate entities, managers, and shareholders involved with the mining industry. Natural resource damage claims, State cooperative agreements, and other State-related issues will not be discussed.

Jan 1, 1988

By J. K. Wolski

This paper addresses the effects of using jet fans as booster fans in mine ventilation networks. A method was developed to determine the pressure generated by jet fans using the momentum theory. The influence of a reduction cone and other ventilation parameters on the jet fan pressure was analyzed. Verification experiments conducted in the Waldo Mine are described. Examples are given to demonstrate the conditions for the effective use of jet fans.

Jan 1, 1998

By James E. Lonergan

To determine the best materials handling system for surface mined materials, one must develop a mine plan for each candidate system based on the most efficient use of that system. This is essential for a fair, unbiased economic compari¬son of the candidate systems. This paper will present two case studies where an integrated mine planning /systems engineering approach has been utilized at different levels of detail in the analysis of an in-pit crushing/conveying system vs. total truck haulage at 2 open-pit copper mines.

Jan 1, 1985

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock' drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

By J. A. Lombardi

"EXECUTIVE SUMMARY The use of membranes for the treatment of Acid-Mine-Drainage (AMD) water has been a 35 year mining industry quest that has only recently produced commercial scale Zero-Liquid-Discharge (ZLD) plants. The process of development of the membrane treatment of AMD has been defined by the water treatment industry’s efforts to control gypsum scaling of the membranes, an artifact of the concentration of calcium and sulfate ions on the concentrate or “brine” side of the membranes. Improved anti-scalants, changes to membrane surface geometry and a lowered permeate flux rate were all part of solving the calcium sulfate (gypsum) scale formation problem. Whether used singly or as part of a multi-stage membrane treatment process, the production of “left over” membrane concentrate or brine, in any volume large or small, was a second barrier to adoption of the method by the mining industry. The two identified “final brine” treatments were a) solar evaporation ponds and b) mechanical evaporators. Brine disposal by solar means is typically site limited to flat terrains or high net evaporation locations. Mechanical evaporation-crystallization is applicable at all sites but, typically, at onerously high ownership and operating costs. Miwatek, a South African water treatment start-up, has entered the mining AMD ZLD marketplace with two new, pilot-scale tested, processes, both of which are predicated on the innovative treatment of a reasonably concentrated AMD and neither of which produces a final brine that requires disposal. In the Miwatek Brine Treatment, MBT, method the membrane brine is caustic pH adjusted and de-calcified precedent to passage through a second membrane plant. The caustic is generated on-site by a lime treatment of the second-membrane concentrate. The first- and second-stage permeates are blended for discharge. The process usually yields no “final brine” for disposal. In the Miwatek Ettringite Treatment, MET, method a low pH first-stage membrane brine is lime treated in two or three steps in the presence of aluminum in a way that metal hydroxide and calcium sulfate solids are formed and purged from the system. Sufficient aluminum is often present in the feed water to, with judicious recycling, enable operation of the lime-aluminum treatment without the purchase of outside aluminum reagent. The first-stage membrane permeate is blended with the lime-aluminum treated membrane concentrate for discharge. The indications are that the method can comfortably meet the low 250 -500 ppm SO4 discharge water quality standards that have most recently been proposed in South America. The process yields no “final brine” that requires disposal. Projected own-operate costs for the MBT and MET systems are less than the estimated costs for all identified alternative treatments."

Jan 1, 2015

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987