Search Documents

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By Paul S. Murphy, Eric W. Oehrke

INTRODUCTION The global market for sulphur has experienced dramatic structural shifts during the past 10-15 years. After a number of years of dominance as sulphur suppliers, the world's Frasch producers were confronted with large increases in nondiscretionary sulphur production from sour crude oil and gas, while escalating energy and exploration costs reduced the economic incentives to replace dwindling sulphur reserves. Sulphur demand also experienced substantial growth, but the majority of this increase was filled by nondiscretionary production. The result was essentially flat demand for Frasch sulphur during this period. This paper briefly summarizes Freeport Sulphur Company's outlook for global supply and demand for sulphur through the year 2000, and examines in more detail the history and anticipated shifts in trade patterns. World trade in elemental sulphur (brimstone), despite year-to-year fluctuations, has been on an upward trend in recent years, and should continue to grow through the end of this century. The type (discretionary vs. nondiscretionary) and location of forecast sulphur supply sources has potentially broad implications for the world's Frasch producers, as they compete in a world market which is increasingly supplied by non-discretionary production. SULPHUR DEMAND Sulphur is a versatile and essential element used in a wide variety of manufacturing processes. Almost 90% of world sulphur consumption is in the form of sulphuric acid. The relatively low cost, ready availability, and physical and chemical properties of sulphuric acid make it the most economical acid for a number of chemical processes. Although sulphur is used in the manufacture of many products, the largest consumer by far is the phosphate fertilizer industry. The majority of sulphur demand growth over the past 30 years has occurred in this area, and today it accounts for nearly 65% of global sulphur consumption in all forms. Due to the relative importance of phosphate fertilizers, sulphur demand is typically discussed in terms of fertilizer and non-fertilizer (or industrial) uses, and this approach will be followed here. We at Freeport believe that global consumption of phosphate fertilizers should grow at an average annual rate of about 3.5% through the year 2000, which is roughly equal to the growth rate experienced during the past ten years. The basic assumption underlying this forecast is that world population will continue to grow significantly, while the total acres of cropland will grow only slightly. Therefore, in order to feed a growing population, higher crop yields will be necessary, which in turn will require the increasing use of fertilizers. This expected growth in phosphate consumption will, without doubt, fluctuate from year to year, and we Frasch producers have painful memories of the large dip in demand during 1982-83. However, we believe that the fundamentals for growth are very good, and that future demand will move back onto the historical trend line. In the recent recession the use of sulphur in the non-fertilizer or industrial sector dropped sharply, and it now appears that future growth will not return to the old trend line. Most of the non-fertilizer uses of sulphur and sulphuric acid involve older industries which are very mature, such as oil refining, steel, pulp and paper, pigments, etc. The use of sulphur in some of these industries is expected to exhibit little or possibly even negative

Jan 1, 1986

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By C. B. Clemmens

Accurately predicting ground control conditions before mining requires a comprehensive exploration approach including photogeologic mapping (satellite and low altitude), delta modeling and, particularly, geophysical logging. In situ properties, density; strength indices; grain size; clay content; and aquifer location, can be estimated with this inexpensive technique. Geophysical measurements can be spot-checked by field or laboratory tests on core samples and by hydrologic (pressure) testing. Each phase of drilling should be accompanied by refinement of the delta model, facilitated by log signatures. Measured properties can then be projected into geologically similar areas. A properly planned program will delineate both the "worst-case" and normal support conditions. Suspect areas can be avoided by mine layout and the mine plan can contain support contingencies for anticipated trouble spots.

Jan 1, 1985

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986

By J. Rothschild

I would like to thank the Society of Mining Engineers for inviting me as well as the other distinguished panelists to spend a morning reviewing and discussing the handling and shipping of industrial minerals. I also would like to thank my management, Cometals. Inc. for permitting me to take time out from the daily hectic pace of marketing and trading to share with you some of our experiences and expertise. Cometals, Inc. is a wholly-owned subsidiary of Commercial Metals of Dallas. The transportation and handling costs of industrial minerals frequently are a major component of the value of the goods marketed and, therefore, it is only natural that close attention should be paid to them. Many of the industrial minerals require special handling to assure that the material reaches the consumer without being contaminated or getting wet. I invite you to accompany me through the various steps involved in "delivering the goods" to the consumer.

Jan 1, 1989

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By Robert H. Oliver

Flowsheet flexibility in new 750 TPH coal cleaning plant provides three unusual capabilities. Two compartment drum coarse H.M. washer can be adapted to provide two stage separation. Coarse section of plant can be operated without fine section when washing surface mined coal. Fine section can operate with flotation cells bypassed if strip coal oxidation kills the froth. Plant can be fed by belt from bulk storage, front end loader from storage piles and truck from the mines. Raw coal and each of four washed products can be fed by belts to three separate loading points on two separate railroads.

Jan 1, 1979

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize biomass productivity, the influence of reclamation practices on biomass production must be well understood, which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass estimations and, also, the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, experimental biomass production plots on reclaimed mine sites established in Wise County, VA, are used for a comparative study of satellite spectral derivatives, which are evaluated against groundbased biomass estimates. Metrics based on four spectral derivatives, band ratios and spectral transforms were regressed against biomass measured in situ for different species. The results demonstrate that greenness and principal component 2 (PC2) were more efficient than the other spectral derivatives for monitoring the biomass of this reclaimed area. Also, it is shown that Landsat-5 TM has provided promising results for monitoring of the biomass changes occurring from 2008 to 2010 over the study area.

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg's, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By Dean Newman, Michael Behrens, Mark Trim, Justin Arifin

Road tunnels in recent infrastructure projects in Sydney, Australia, are designed to have a fire resistance level of either a 4-hour cellulosic fire or a 2-hour hydrocarbon fire. Where permanent ground support for tunnels consists of systematic rock bolts and relatively thin layer of shotcrete, it is important to ensure that during and after the fire event the ground support is designed/predicted not to pose risks to the tunnel occupant. The global behavior of the ground support can be predicted using finite element analysis, and its resistance is derived with consideration of the material strength degradation due to the elevated temperature.

Dec 1, 2022

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

By Donald E. Scheck

Blasting practices based on sound engineering principles are well established but the successful application of these practices requires accurate information about the overburden geology and close supervision of the drilling and blasting operations. Good design alone is not sufficient to insure good results, but the process may be difficult to control unless steps are taken to measure the variables and to provide management and the operators with the information they need to establish and maintain control. Satisfactory blasting can be defined as loosening and fragmenting the rock so that it can be handled by the excavating equipment, while at the same time, governmental regulations on air blast and ground vibrations are not violated. Optimum practices achieve these objectives at the lowest combined cost of the drilling and loading operations and the blasting materials. Total system optimization, that is, taking into consideration the effect of fragmentation on the cost of operating and maintaining excavating equipment as well as drilling and blasting costs, probably is not a reasonable goal at the present time.

Jan 1, 1984