Search Documents

By G. Deschênes

In an earlier study (Deschênes et al., 2009), gold and silver were shown to be efficiently extracted from samples taken from the Kupol Mine in Russia using lead nitrate in a cyanide leach system. In the current study, a com-parison of the technical and economic merits of a new technology called CANMET enhanced leaching process (CELP) was made with the cyanidation/acidification-volatilization-recycling (AVR) process using eight metal-lurgical variability samples, as well as a large composite sample, which was to represent the initial two years of Kupol mill feed. The composite sample leach feed assayed 33.4 g/t Au and 289 g/t Ag. The metallurgical results from the large composite sample demonstrated that CELP produced very similar gold and slightly higher silver leach extractions compared to the conventional cyanidation/AVR leach conditions at 1/2 the cyanide concentra-tion (1,000 ppm NaCN in CELP vs. 2,000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton was approximately the same for the two technologies (total cost of CELP with the use of Merrill-Crowe at $46.48/t, with cyanidation/AVR at $46.13/t). However, the implementation of CELP would eliminate a capital expenditure of approximately $5 million for an AVR system based on a 2005 feasibility level cost estimate. Eight variability samples used to confirm the composite sample results showed that, on average, the gold leach extractions with CELP and the conventional leach conditions were very similar, but the average silver leach extraction was 2.1% higher for CELP. Furthermore, CELP silver leach extraction was 4.6% higher on average compared to conventional cyanidation for the four mid-grade variability samples evaluated. The decision was made to remove AVR cyanide recovery from the flowsheet and implement CELP at Kupol. The ability to use the conventional leach equipment with CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2010

By B. J. Vorster

The South African Iron and Steel Company Ltd operates a large Iron Ore Mine in the Cape Province of the Republic of South Africa. The Mine is situated on the farm, Sishen, approximately 600 km west of Johannesburg. The annual capacity of the Mine is 100 million ton of ore and waste and the present production level is 60 million ton. The Mine operates continuously for 6 days a week. The primary equipment used to maintain the above production are 55, 154 t trucks (Wabco and Unit Rig) and 14 P & H shovels. During 1979 an urgent feasibility study into the application of a trolley assist system was launched at the Mine. This was due to the unrealistic escalation in the cost of diesel fuel and the appeal from the South African Government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technical feasible. The estimated discounted cash flow return exceeded 50% and the diesel fuel consumption would be reduced by 120 million litres in the next 10 years. Management subsequently approved the implementation of the system at Sishen. The construction of 7,7 km of line and the conversion of 66, 154 t trucks were completed in March 1982.

Jan 1, 1985

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By B. T. Mirabile, D. Tang, Y. Luo, S. S. Peng, C. T. Holland

Knowledge of local coal mine roof geology is critical to the design of a safe and suitable mine structure. An automated drill control and data collection system has been designed for a J.H. Fletcher twin-head roof bolter. Drilling parameters collected during the drilling process can be used to interpret geologic features intercepted in the mine roof. The drill and data collection system have been tested in both laboratory and underground settings. Visualization of certain drilling data has shown good correlation with geology drilled. A quantitative prediction model was developed using drilling parameters examined with data visualization. The quantitative model was tested using laboratory drilling data.

Jan 1, 2004

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By G. Zain, Abdel-Zaher M. A. Abouzeid, Y. S. Mustafa, A. A. S. Seifelnassr

The main forces acting on minerals in conventional size reduction units are compression, impact, attrition, and/or abrasion. Usually a combination of these forces shares the breakage action of the minerals with one or more of these forces dominating the breaking action, depending on the machine used. The present work concentrates on the behavior of quartz when stressed with compression force in a confined piston die. Several size fractions within the size range minus 10 mm to plus 0.85 mm were compressed in the piston die. The measured parameters are compression load, bed thickness, displacement as a result of compression, rate of displacement, and the size distribution of the products. It was found that the size distributions are, to some extent, different from those produced by the ball mill or the high-pressure roll mill. This is mainly because of the differences in the type of the acting forces in each case. It was also found that the cumulative weight of the distributions is reasonably normalizable with respect to the median particle size of the product. The specific energy expended is inversely proportional to the median size of the products, and the reduction ratios, xf/xp, are directly proportional to the applied compression force, and hence, to the specific energy expended. A simple model is suggested for predicting the particle size distribution as a function of the expended energy. The calculated values of the size distributions match fairly well with the experimental values, except at the very low energy levels, where most of the energy expended is consumed in the rearrangement and packing of the particles in the confined space with little or no breakage.

By N. Magdalinovic

Generally speaking, erosion, as a process which entails degradation of surface layers of earth under the influence of the mechanical energy of surface waters, and from the point of view of biosphere sustainability, is a harmful process. This is absolutely true when agricultural and forest areas are concerned. However, if erosion is viewed selectively, this general definition about its harm raises serious questions. In other words, the erosion which takes place in the terrains where there is no vegetation because of the geological composition of the soil, does no harm. On the contrary, if the mineralogical composition of such terrains is characterized by a presence of precious and rare metals, erosion can be very useful. It contributes to the creation of new alluvial deposits of these metals in the waters in the plain land. It is here that torrents from hills come down and cause erosion. And finally, if there were no erosion, there would be no renewable deposits of gravel and sand.

Jan 1, 2007

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By W. Fletcher

Startup of a new plant is a very interesting time. It generally is also a very demanding and often frustrating period. Startup problems can become serious ii they impede the early achievement of full plant production. Raw materials are wasted, manpower is unproductive, field modifications can be extremely expensive and market commitments may not be met. This paper outlines a well proven and highly successful approach to eliminating many of the problems and frustrations often experienced in plant startup. The procedures and methods summarized in the following paragraphs have been developed over a period of 25 years during which some 90 plants were started up.

Jan 1, 1981

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By K. C. Li

The scope of this subject is a broad one. The demand for a metal with high refractory properties, great strength at elevated temperatures and high nuclear cross section, has put tungsten in the foreground as: the most promising metal to fill some of these requirements. Recently developed techniques have made it possible to roll large tungsten sheet and-the availability of fabricated tungsten is already upon us. More and more, the demand is for purer and still purer metals. Tungsten is no exception. As technology improves, we are learning more about the effect of foreign elements in minor amounts upon the chemical and physical properties of metals. As equipment and technology improve, specifications become more rigid, and reasonably so. Pure metals have revealed properties hitherto unknown in metals produced by former technology.

Jan 1, 1961

By Tim Lundquist

Disa Technologies Inc. provides innovative, sustainable solutions for mineral processing and remediation through its patented High-Pressure Slurry Ablation (HPSA) technology. HPSA processes solid feed material in slurry form, propelled by high pressure pumps through opposing nozzles that generate impinging jets within a collision housing. This process induces particle-to-particle collisions in a high energy zone, creating intergranular fractures along grain boundaries. In our batch scale and continuous operating testing, we have found that controlling key processing variables such as nozzle velocity, slurry solids percentage, and the number of passes can allow for controlled size reduction and maximum mineral liberation. Since 2018, Disa Technologies has demonstrated the versatility of HPSA by testing it on diverse materials, including phosphate, copper, uranium, vanadium, zinc, rare earth elements, lithium, nickel, mineral sands, gold tailings, and more. The intent of this paper is to present an overview of our test results describing in detail impacts on size reduction, recovery, and grade with a focus on HPSA's adaptability across ore types. Looking forward, it explores the potential to process materials such as DR-grade iron, clay, PGMs, bauxite, and various tailings. Additionally, it examines planned advancements in HPSA technology, including optimized nozzle spacing, higher capacity models, improved tonnage-to-footprint ratios, enhanced maintenance features, and expanded nozzle configurations.

Jan 1, 2025

By N. J. Themelis

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early thirties in the so-called Hadsel mills (Figure 1) mainly used in gold mines on the U.S. West Coast. A number of these mills were built in sizes of 20 to 24 ft. in diameter and five-six feet in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill (Figure 2), the Aerofall dry grinding mill and others. A tabulation of all known autogenous and semi-autogenous installations around the world was sent recently to the authors by Hr. G. J. Kushner of the Koppers Mineral Processing Division. In the size range of 24 to 32-ft. in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 36-ft. dia X 15-ft. long mills in Minnesota, powered by 12,000 hp. motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above one hundred and fifty mills was in operation prior to 1964.

Jan 1, 1978

The surface properties of eight coal samples were studied by measuring contact angles, coal oxidation, equilibrium moisture and film flotation. The penetration tests were carried out with do de cane, while dodecane and MIBC were utilized in batch flotation tests and in the simplified release analysis. Coal floatability results from the properties of coal organic matter and coal liberation. While the wetting of coal by water seems to be determined by the surface properties of coal organic matter, wetting by hydrocarbons correlates very well with the content of coal mineral matter.

Jan 1, 1992

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By Eugene R. Palowitch, Albert W. Deurbrouck, Thomas H. Parrsons

INTRODUCTION Hydraulic concentrators utilize the physical characteristics-size, shape, and specific gravity-of particles suspended in a fluid medium to effect a concentration of desired quality. Fine-coal concentrators include generally those devices which are used to clean roughly 3/4, in. (9.5 mm) top-size coals. While this size designation is somewhat arbitrary, it is consistent with current practice although some fine- coal concentrators can treat coarser coals effectively. A variety of devices have been and are currently being used to wash fine coals and include: dense media cyclones, wet concentrating tables, hydrocyclones, jigs, spirals, launders, and upward-current classifiers. As launders and upward-current classifiers have been replaced by more efficient devices, they no longer warrant consideration as fine-coal washers. And as fine-coal jigs were addressed with the Baum jig under Part 1, Section 2, and heavy media cyclones and hydrocyclones were addressed under Part 2, Section 1, of this Chapter, only the wet concentrating table and the spiral concentrator will be discussed here. WET CONCENTRATING TABLES History The current wet concentrating table evolved from continuous belt concentrators which utilized a flowing film of water to recover heavy metals. In these devices the heavier concentrate moved up the inclined plane of the belt while the lighter impurities were washed away by water flowing down the belt. The natural outgrowth of the continuous belt concentrator was the vanner, a vibrating endless belt which was first developed about 1860 by Hartwig. Later models of the vanner, such as the Frue, incorporated oscillation in a plane transverse to the direction of the water current. Excellent descriptions of these washers are found in The Cleaning of Coal, by Chapman and Mott.80 Further development of tables included the circular stationary table (Linkenbach), the multiple round table (Anaconda-Evans), the bumping table (Campbell), and finally the differential-motion table which is now used extensively for cleaning fine coals.

Jan 1, 1991