Search Documents

By W. D. Bachman

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from Kennecott Copper Corporation's Chino mine. The efficiency with which the various samples could be ground was found to vary over an extremely wide range, even among samples taken from different locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale non-homogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully.

Jan 1, 1970

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By L. L. Chasko, D. W. Alexander

Researchers from the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries.

Jan 1, 2014

By Ronald M. Hays

During the twentieth century the Mesabi Range in northeastern Minnesota has been the major source of iron ore for American steel mills. The Mesabi Range extends along an iron bearing outcrop known as the Biwabik formation. This outcrop is some 120 miles long and up to three miles wide. The formation is from 200 to 650 feet thick and dips 5 to 10 degrees to the southeast. The iron content of the original Biwabik formation was quite uniform, but much of this formation has been subjected to alteration. Thus major variations in iron content and mineral composition exist both laterally and vertically in the present Biwabik formation. The remaining unaltered iron formation includes the magnetic taconites which are commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons. per year of iron pellets and have produced approximately 170 million tons of pellets since 1956. Capacity for another 30 million tons per year of pellets is being considered by the industry for the next ten years. This increase will be obtained by construction of new plants and expansion of present operations. Thus by 1977, it is estimated that approximately 60 million tons per year of iron pellets will be produced from magnetic taconite on the Mesabi Range. The portions of the Biwabik formation subjected to intense alteration resulted in the direct shipping, wash and heavy media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron for American steel mills. In 1966, 12 million tons of direct shipping ore and 18 million tons of wash, jig, heavy media and other gravity concentrates were shipped from the Mesabi Range. These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from about 30 million tons in 1966 to 6 to 8 million tons in 1975. This decrease will be due to depletion of reserves and poor quality product.

Jan 1, 1968

By T. G. Legare

It is now well documented that trace amounts of silver, gold, and platinum group metals occur in certain geothermal brine deposits. A significant body of literature has been generated over the last twenty years which describes attempts to quantify the frequency and levels of these precious metals in the brines. This literature is often confusing and contradictory. For example Barnea 1 states that the Salton Sea geothermal field carries 2 ppm gold, yet more recent data by workers at Lawrence Livermore National Laboratory2 (LLNL) concludes that the gold level in Salton Sea brine is <0.07 ppb. They report a platinum level in one well of 55 ppb. This apparent contradiction may be explained by sampling source and technique, but is most probably explained by difference in analytical technique. Analytical techniques and problems will be discussed in the next section.

Jan 1, 1985

By L. L. Chasko, D. W. Alexander

Los investigadores del National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research han evaluado los efectos que la malla de control de suelos podría tener en la distribución de polvo flotante de roca y carbón en minas de carbón. El creciente uso de mallas para controlar el desconchado o caída de material del techo y las vigas introduce superficies elevadas adicionales para recolectar el polvo de roca o de carbón. Es posible que el potencial para la propagación de explosión del polvo se incremente si el polvo flotante de carbón no es convertido en inerte de manera adecuada. Adicionalmente, la malla podría interferir con la recolección de muestras representativas de polvo cuando se usa el método de recipiente y brocha desarrollado por la U.S. Bureau of Mines y usada por la Mine Safety and Health Administration para muestreo de banda. Este estudia hace una estimación del polvo de roca o carbón adicional que pudiera acumularse en la malla y desarrolla un método para recolectar muestras de polvo representativas atrapado en las mallas.

Jan 1, 2014

By K. P. Wang, Ta M. Li

The Chinese energy and mineral industries are readying themselves for a period of dynamic transition, unprecedented in the country&apos;s long and sometimes turbulent history. The transition comes as a result of the government&apos;s new program of "Four Modernizations" in its agricultural, defense, industry, and science and technology sectors. The announced program is generally considered by Western observers to be a moderate, pragmatic approach to get China on the road to industrial parity with Western nations by the year 2000. The game plan calls for integration with the West to beef up Chinese know-how and the purchase of foreign technology to supplement areas where China lacks the ability to do so itself. While the role of energy and minerals is not specifically mentioned in the program, it was made clear to ME that China realizes the basis of any sustained modernization program is tied closely to the health of its minerals sector. Various published reports have indicated the existence of an already vibrant energy and minerals sector with world rank production in coal, iron ore, tin, antimony, cement, pyrite, asbestos and tungsten to name just a few. For the most part, except for the export metals, the primary focus of China&apos;s production has been on fulfilling domestic needs. Now the new initiatives are aimed not only at self-sufficiency, but also on propelling the country&apos;s natural resource clout into international prominence. With a mineral resource base that is considered by many westerners a potential bonanza, China&apos;s new long march toward modernization will be an exciting adventure, well worth watching. Big Projects Spark Excitement China&apos;s renewed commitment to a more liberal program is as much a desire to "walk on its own two legs" as it is a backlash from the frustrating years that followed the Cultural Revolution of the 1960s and early 1970s. Much of the early excitement was initiated by China&apos;s Premier and Party Chairman Hua Guo-feng in speaking to the fifth National People&apos;s Congress (NPC) in 1978. Here, Chairman Hua presented the Communist Party&apos;s 10-year blueprint for economic development. Specifically, the Party&apos;s plans called for completion of 120 large-scale industrial projects by 1985. Mentioned were 10 new iron and steel works, 30 power plants, six new railways, 10 oil and gas fields, nine nonferrous metal

Jan 3, 1980

By Charles A. Beasley

Coal conversion to electricity or to substitute natural gas requires a significant quantity of natural and human resources including, in addition to the coal resource base, land, water and the construction and operating labor force. Each method of coal conversion has its advantages and disadvantages relative to conversion efficiency, preferred method of resultant energy transportation, resources consumed, and impact on the environment. Regulations which have been passed in recent years to maintain or restore the pre-project environment can add significantly to the capital and operating costs of both a conversion facility and its associated mine.

Jan 1, 1983

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By Steve Kral

As the mining industry watches commodity prices continue to soar, the question on most everyone’s mind is how long will this upcycle last. The con-census among speakers and attendees at the SME Annual Meeting and Exhibit is that this cycle is sustainable. The buzz at the meeting was, of course, the current boom cycle the industry is in. Most agree that China’s huge appetite for mineral commodities is part of the force driving the upturn. But the improving economies of other developing nations also plays a role. However, along with the good times come challenges. Speakers at the keynote session addressed some of the challenges and offered their opinions on the sustainability of the boom.

Jan 1, 2006

By Parris A. Lyew-Ayee

The Government or Jamaica has just completed agreements with four of the five bauxite/alumina companies operating in Jamaica. These companies are Kaiser, Reynolds, Alcoa, and Alcan, and the Agreements came into effect on February 1, 1980. One of the results of these new Agreements is the Acquisition of all company-owned bauxite lands by the Government and the rationalization of bauxite reserves.

Jan 1, 1980

By N. Dashbold, E. Rudnik

"Waste electric and electronic equipment currently comprises the fastest-growing waste stream in the world, but at the same time it is seen as an important source of metals for the recycling industry. E-waste is usually treated pyrometallurgically, with hydrometallurgical methods used to a lesser extent. This paper reports the results of research on the selective recovery of copper from smelted low-value electronic waste. Pyrometallurgical pretreatment of the scrap allowed the removal of plastics and the increase of metal content in the material. The obtained alloy of copper, zinc, tin and silver was a multiphase solid consisting of two brass phases and inclusions rich in iron, lead and silver. Copper alloy was further anodically dissolved in ammoniacal chloride solution. It resulted in high degradation of the material and accumulation of the metals mainly in the slime. The slime was then leached in acid or ammoniacal chloride and sulfate solutions followed by selective copper electrowinning. Hydrochloric acid was the most efficient solvent for the slime, but ammoniacal solutions were more selective for copper. Copper could be leached with 96 to 100 percent and 87 percent efficiency from the slime by the chloride and sulfate solutions, respectively. Copper with 90 to 99 percent purity at current efficiency of 42 to 76 percent was obtained from the acid solutions, while copper with 98 to 99 percent purity at current efficiency of 60 to 86 percent was deposited from the ammoniacal baths. IntroductionObsolete electrical and electronic equipment makes up the fastest-growing waste stream in the world (Baldé et al., 2015), due not only to the introduction of wider ranges of new types and models of a variety of electronic products but also to the shortening of their life-spans, sometimes referred to as planned obsolescence by producers (Keeble, 2013). About 42 million tons of electronic waste, or e-waste, are estimated to have been generated globally in 2014 (Baldé et al., 2015), and it is expected that in the European Union alone the waste electrical and electronic equipment (WEEE) stream will reach more than 12 million tons by 2020 (European Commission, 2015). Accurate evaluation of e-waste generation (Wang et al., 2013) and its global transport (Breivik et al., 2014) is difficult, mainly due to a lack of high-quality data related to its market and socio-economic dynamics.Many countries introduced legislation to control e-waste flow, collection and recycling. For example, Directive 2012/19/EU on waste electrical and electronic equipment (European Parliament and the Council of the European Union, 2012) obliges all E.U. members from 2016 to maintain a minimum collection rate of 45 percent of the total weight of WEEE collected. From 2019, the minimum collection rate to be achieved annually shall be 65 percent of the average weight of electronics placed on the domestic market in the three preceding years, or alternatively 85 percent of WEEE generated in the territory of the particular member."

Jan 1, 2017

By Miles L. Silberman

Three major suites of igneous rocks were erupted in the Great Basin in middle and late Cenozoic time. The first, most likely, resulted from sub- duction of a Pacific plate (Farallon plate) beneath the North American plate, resulting in eruption of andesitic rocks in the northern Great Basin between 42 and 43 m.y. ago. Between 34 and 17 m.y. ago, igneous activity migrated to the southwest, largely as eruption of volumincus rhyolite-quartz latite ash-flow sheets, ending about 17 a.y. ago with the onset of crustal extension and north-south-trending Basin and Range (rift) faulting. The second volcanic suite erupted between 17 and 8 m.y. ago in the northern Great Basin; is mostly basaltic or bimodal basalt-rhyolite. The third volcanic suite consists of andesitic and rhyolitic lavas and some basalt erupted between about 22 to 6 m.y. ago in the western Great Basin along the northwest-trending Walker Lane fault zone. Hydrothermal ore deposits are associated with all suites of igneous rocks, but the largest production has come from mines associated with andesitic rocks of the third (western Great Basin) suite. The oldest (34 to 42 m.y.) andesitic rocks (first suite) of the northern Great Basin have produced some large deposits; slightly younger silicic rocks of this suite are mostly barren. Many small ore deposits are associated with the 17- to 8-m.y.-old basalts (second suite) of northern Nevada.

Jan 1, 1976

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Refractory gold ore contains sulfide minerals like pyrite, chalcopyrite and sphalerite that are difficult to be directly leached by cyanidation or by lixiviants such as thiourea and halides. In such cases, it is necessary to perform oxidative pretreatment of the ore to oxidize the sulfide matrix, and gold particles can be exposed to the solution during the leaching process [1]. In recent years, hypochlorite and chloride solutions have been introduced as alternative materials for hydrometallurgical methods of gold extraction instead of cyanide solution [2]. A previous study by Hasab et al. [3] reported that the gold dissolution rate in hypochlorite solution was higher than in the cyanidation process, due to the presence of hypochlorous acid (HOCl) as a strong oxidizing agent. In a hypochlorite leaching system, the change in pH can influence the presence of oxidant species in the solution: the hypochlorite ion (OCl−) is stable in pH greater than 7.5, HOCl can be found in pH between 4.0 and 7.5, and aqueous chlorine (Cl2 (aq)) is the predominant oxidant when pH is below 4.0. As HOCl is the most effective oxidizing agent for gold extraction, pH should be maintained in the range of HOCl stability [4].

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By P. K. Sims

One-day field trip via U.S. Highway 6 and Colorado Highways 119 and 279 from Golden, Colorado to Idaho Springs. This field trip provides an opportunity to observe aspects of the Laramide ore deposits in the Central City and Idaho Springs mining districts and the Proterozoic basement rocks, which host the ore deposits.

Jan 1, 1986

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023