Search Documents

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By J. von Schéele

OXYFINESTM is an oxyfuel-based concept for in-plant recycling. It enables the possibility of fines, dust, sludge (without any drying step) and other by-products generated by the steel- and metal-producing industries to be recycled directly back into existing processes or a separate on-site unit. The results from a full-scale installation (20 000 t/a) and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. The latter include materials arising from ferrosilicon, ferrochrome and silicon manganese production. The concept not only provides a solution to the problems associated with dust and sludge generated in metal production, it also turns these materials into a low-cost raw material which is useful for the same production process, thus replacing some of the raw material input. If required, it could also be used, possibly as an intermediate solution, to convert the dust or sludge into an inert material with a suitable shape. Under some conditions, a directly saleable product could also be obtained. The paper reviews this technology, its status and benefits as wells as its possibilities with regard to application in ferroalloy production. Keywords: recycling, fines, dust, sludge, ferroalloys

Jan 1, 2004

A large number of brittleness concepts have been used in very different studies in the literature. One of them is the B1brittleness concept. In this study, the objective is to criticize the B1 brittleness concept on rotary blast hole drills. The B1 brittleness concept, the ratio of uniaxial compressive strength (sc) to tensile strength (sT), are widely used as a rock brittleness concept in the literature (Inyangand Pitt, 1990; Verhoef, P.N.W. 1993; Neil, D.M. et al.1994;Becker, et al.1984; Evans and Pomeroy, 1966; Göktan, R.M.1992; Kahraman, S. 2001; Yamaguchi, U. 1970; Verhoef, P.N.W. et al.1996; Bilgin, 1982; Howarth and Rowlands,1987; Howarth, D.F. et al. 1986). So, it was used as a rock brittleness concept in this article. The value of the B1brittleness concept is equal to the tangent of ß angle in the following graph. It was seen that more meaningful relationships could be obtained with the B2 brittleness, the under ?Area?(= 1/2(scxsT) = B2) under the curve, instead of tangent ß, (=B1), of the curve.

Jan 1, 2003

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

It is well known that the electrochemical precipitation of metals from aqueous solutions is conducted by the electrochemical standard potential scale. This scale indicates the order of nobility of different metals. Consequently, the standard potential scale shows the nocivity of metals when they are present as impurities in aqueous solutions containing metals. In the hydrometallurgy of cobalt, nickel and zinc are co-deposited during cobalt electrodeposition. Nickel has almost the same chemical, physical and electro-chemical properties as cobalt. Furthermore, the electrochemical potential of nickel is relatively higher than that of cobalt. For this reason nickel is preferentially reduced at the cathode in the presence of cobalt. The presence of small amounts of zinc in solution leads to contamination of cobalt electrowon. In spite of its lower electrochemical potential in comparison to cobalt, zinc is reduced on the cathode because of its higher hydrogen-overvoltage. But, in the hydrometallurgy of zinc, small amounts of cobalt present solution will contaminate the zinc reduced at the cathode. This is easily explained by the fact that cobalt is more electropositive than zinc. The co-deposition mechanism of sulphur at the cathode is not yet well understood. Great attention has to be paid to the mechanism of co-deposition of sulphur during cobalt electrolysis. This work aimed to investigate the influence of some parameters on the co-deposition of nickel, zinc and sulphur during cobalt electrowinning. The following parameters have been investigated: Co2+concentration in the electrolyte, current density and ammonium sulphate (NH4)2SO4additions. It has been established that important nickel, zinc and sulphur co-deposition takes place at relatively low Co2+ concentration in solution. The behaviour of these elements with regard to the cathodic phenomena has been established.

Jan 1, 2005

The 109th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 16 August 2006. Special General Meeting A Special General Meeting to consider the changes to the Constitution was held immediately prior to the AGM. 1. Purpose In order for the SAIMM to remain relevant and ensure maximum value to all members, Council propose three changes to the Constitution. 2. Background Three changes to the Constitution were proposed by the Council on 21 July 2006. These changes now have to be approved by means of a ballot at a Special General Meeting. These three proposed changes are discussed briefly below:

Jan 1, 2006

By J. Eriksson

Slag from stainless steelmaking is known to disintegrate, which is an environmental problem and prevents the cooled slag from being utilized. This disintegration is due to the transformation from the ßto the ? polymorph of di-calcium silicate. The transformation is accompanied by an increase in volume of about 11% and a total disintegration of the slag. AOD slag from stainless steelmaking was re-melted in a laboratory induction furnace, together with olivine and calcinated dolomite, to investigate the prevention of disintegration by increased MgO content of the slag with small changes in CaO to SiO2ratio. The modified slag was examined with X-ray diffraction and scanning electron microscopy. The trials showed that an increased MgO content can change the mineral composition towards formation of more Merwinite and Bredigite, which prevents disintegration of the slag. Keywords: slag, disintegration, di-calcium silicate

Jan 1, 2004

By D. Xie, S. Sun

An overview of recent development of CSIRO?s Multi-Phase reaction models will be presented with examples comparing the calculated physico-chemical properties of metallurgical slags with the existing experimental data. The paper will also outline the development of a kinetically based model for molten bath reactors and its application to submerged combustion of coal in a slag bath as well as the reaction between the slag and injected coal particles. The plume model combines established models for the combustion of pulverized fuel with models for the growth and rise of bubbles from a lance or tuyere. This model predicts the extent of de-volatilization and combustion of the coal in the plume, the utilization of oxygen and the exchange rate of oxygen between the gas and the bath as well as the heat transfer rate between the gas bubbles and the bath. The slag reduction model brings together the recently measured rate data and fundamental understanding of the kinetics of CO-CO2reaction with iron oxide containing slags and predicts the changes resulting from injection of coal particles into molten slags. The top-space model covers reactions between gases and molten droplets in the post-combustion zone, where heat and mass transfer between phases results in higher utilization of the fuel values in the partly oxidized gases and transfer of heat to the molten bath. Keywords: Phase equilibria, viscosity, electrical conductivity, slags, kinetics, reaction rate.

Jan 1, 2004

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By R. P. H. Willis

For technology transfer to be successful a process, from research to full scale application, has to be followed. This paper describes such a process and how it is applied in practice. Some of the ?do?s? and ?don?ts? are highlighted. Recommendations are made on how to communicate existing knowledge and to ensure that a framework exists to effectively plan future projects with final technology transfer objectives firmly in place. The Impact Ripper System is used as a case study to illustrate lessons learned. Key words: Technology transfer, implementation

Jan 1, 2002

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By S. Pal, A. K. Lahiri

Most of the compounds present in slag are surface active. This gives rise to foaminess of slag. The foam life and foaming index are normally determined by the draining rate of slag through the plateau border, so the foaming index is directly proportional to slag viscosity and inversely proportional to slag density and bubble diameter. When a small amount of a strong surface active compound like P2O5or Cr2O3is present in slag, however, the foam life increases significantly and the above relationship is not obeyed. The strong surface active compounds reduce the draining rate from the film between the adjacent bubbles so the film draining controls the life of the foam. The thickness of the film, Marangoni force, viscosity of the slag, and diffusion of surface active compounds determine the film draining rate. The interplay of these factors leads to very low or high film draining rates and affects the film and foam stability significantly. Keywords: slag, foam, foaming index, film draining

Jan 1, 2004

By R. L. Lawson

I?ve been asked to appraise the global role of coal and mining, and the best place I can think of to begin is with the World watch Institute, which purports to monitor all things global. Last fall the institute?s magazine, entitled World Watch, in a cover story called for a worldwide campaign to outlaw the use of coal before this century?s end. To my mind the article began the campaign. However, the institute had to admit that no such ban will be possible unless there is special help and heavy intervention?that is, novel policies and punitive taxes. I?ll quote directly from the magazine to underscore the point: ?without them the market will continue to deceive us into thinking coal is cheap, abundant and irreplaceable?.

Jan 1, 2001

By H. G. Denkhaus

Comment on ?The evaluation of rock brittleness concept on rotary blast hole drills? in the Journal of SAIMM, vol 102. no. 1. pp. 61?66 Comment on ?Correlation of specific energy with rock brittleness concepts on rock cutting? in the Journal of SAIMM, vol 103. no. 3. pp. 163?171by R. Altindag Foreword Some thirty years ago it was almost customary that articles in South African technical and scientific journals were followed up by discussions in which the reader(s) expressed criticism and/or added to the information contained in the article. This custom has obviously died out, be it that the articles are nowadays of such a high standard that nothing can be added or be it that the receivers of the Journal suffer from an information inflation and do not read the articles anymore. I now have the temerity to offer a discussion to an article that recently appeared in the journal, namely ?The evaluation of rock brittleness concept on rotary blast hole drills? by R. Altindag (J.S. Afr. Inst. Min. Metall., vol, 102(2002), pp. 61?66.

Jan 1, 2003

By B. J. Buys

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resin-anchored rock bolts was investigated. Axisymmetrical and three-dimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios. Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.

Jan 1, 2009

By E. Harris

Frithia humilis is an endangered succulent plant species. Its distribution range overlaps with the coal fields of Mpumalanga and it is therefore threatened by opencast mining activities in particular. One of the 11 known populations of F. humilis was translocated from a licensed coal mining site to three suitable receptor sites within the species? distribution range. A longterm monitoring programme was initiated to track the progress of the newly established populations. Temporal trends in population demography, size classes, and fecundity were recorded. Population numbers of size classes fluctuated annually. However, flower frequency increased over time and seedling recruitment contributed significantly to population growth. Receptor sites with similar geological conditions to the donor site had more persistent cohorts, which suggest that such sites should receive priority during the translocation of endangered edaphic specialists. This study not only confirms that a Frithia humilis population can successfully establish after a translocation, but also serves as an important baseline for future comparative purposes to gauge the long-term success of the translocation effort.

Jan 1, 2014

By Dave Capstick, Ken Garner, Jim Porter

Technologies and systems used in the management of energy consumption in the mining and metal processing industry are well understood and documented from the supply side of the business. It is our contention that in many instances, through a more complete understanding of the demand side of the business, based on the detail of the operations plan, will provide greater lead time in terms of the design, implementation and utilisation of power supply infrastructure. Thus, optimal management of demand in a proactive manner, based on production requirements, will ensure both security of supply as well as continuity of operations. This paper describes the technology and methodology that is being developed to enable the above statement to be achieved. We use a case study to demonstrate the ability of the tools and methodology and conclude by outlining the business benefits achievable as well as the future developments emanating from this initiative.

Jan 1, 2005