Search Documents

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By P. K. Hofmeyr

Traditional fire assay dates back over 3000 years and has changed very little over that time. The only improvement is to replace the gravimetric finish with dissolution of the Precious Metal bead followed by AA or ICP analysis of the solution. The newly developed FIP A (Fast In-line Fire Assay) method allows full automation of the fire assay process from sample preparation to spark analysis of the Pb button. This results in fully quantitative analyses for Pt, Pd, Rh, Ru, lr, Au and Ag in typically less than an hour after a sample is entered into the system. Detection limits are theoretically Pt 0.08 ppm, Pd 0.002 ppm, Rh 0.002 ppm, Au 0.08 ppm and Ag 0.002 ppm but in practice the lower measurable limits are about double these figures. Few opportunities have been available to present data obtained using the FIFA system as all FIFA laboratories have been in the domain of a Pt mining company which prefers to keep all Pt analytical matters confidential. However, IMP has recently participated in the round robin exercise to establish recommended values for a new series of Merensky Reef and UO-2 Layer reference materials produced by African Mineral Standards. The precision of the results was excellent being on average Pt 2.05%, Pd 1.25%, Rh 4.08% and Ru 4.94% being expressed as Relative Standard Deviation. The excellent precision is a reflection of the efficient collection of POEs in the Pb buttons and the homogeneity of the Pb buttons. However, the accuracy was not as good. The poorer accuracy is interpreted as the calibration of the spectrometer not being as good as desired due to the difficulty in acquiring a suitable range of standards with reliable recommended values for the PGEs. The most recent spectrometer was calibrated with the greatest care and produced slightly better results for Pt, Pd and Rh and slightly worse for Ru.

Jan 1, 2014

By J. Petersen, K. Shaik

The traditional route utilised for the recovery of Platinum Group Minerals (PGMs) in South Africa involves the concentration of ore by flotation, followed by smelting to produce a PGM rich matte, which is then digested hydrometallurgically to solubilise base metals and Platinum Group Elements (PGE). HCl/Cl2 is conventionally used for PGE dissolution from concentrated material, which is an aggressive reagent associated with high maintenance costs as well as environmental concerns. Of interest is the leaching of PGMs directly from mineral ores, low grade concentrates and tailings in a cyanide-ferricyanide system as a more sustainable alternative. This system has shown favourable Pt recoveries among the Pt minerals, but with sperrylite (PtAs2) displaying highly refractory behaviour. The dissolution of sperrylite is investigated in a cyanide-ferricyanide system in the context of an electrochemical study involving OCP, chrono-amperometry and cyclic voltammetry. This approach allows the assessment of leaching characteristics as well as the investigation of surface passivation, which is believed to contribute to poor Pt recoveries. Some evidence is presented that such passivation is related to the formation of arsenide species on the mineral surface. Keywords: Sperrylite, PGMs, cyanide, ferricyanide, electrochemistry

Jan 1, 2020

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By T. Uysal

Various morphological parameters that affect the flotation recovery of sphalerite were modelled and optimized using the response surface method (RSM). The effects of roughness value, shape factor, and collector concentration were investigated using the central composite full design method. The results were evaluated by analysis of variance. The optimum roughening time was found to be 25minutes, the optimum roughness value was 2.9071 μm, and the optimum collector concentrationwas 0.001 M. Using these values, a flotation recovery of 98.01% was obtained. Similarly, in shapefactor studies, the optimum grinding time was 15 seconds, the optimum roundness value 0.7421, and the optimum collector concentration 0.0009 M, which resulted in a flotation recovery of 94.30%. The average error between the optimization results and the experimental results was estimated to be less than 6%, and the R2 values were greater than 90%. The study shows that RSM can be effectively applied in finding the economic optimum condition for obtaining maximum flotation recovery with minimum reagent consumption.

Sep 6, 2023

By A. Yamik

This research study includes studies carried out on the recovery of unburned carbon in the ashes of Tuncbilek Thermal Power Plant. Bottom ashes have been identified by X-ray diffraction and X-ray fluorescence. These samples are potentially of class F type and have significant amounts of unburned coal. According to the ash amount that units in the thermal power plant produce, and the analyses of the samples mixed, which used certain amounts in flotation tests, it was found that the bottom ash includes 91.47% ash in dry form and 8.53% combustible matter, and the lower calorific value is 491 kcal/kg. Optimum flotation conditions to get the unburned carbon were subsequently determined by examination of the optimum flotation grain size, pulp density, collector type and amount, depressant type and amount, frother type and amount, agitation speed, and froth-taking time. While the lower calorific value of the thermal power plant bottom ashes of the 3rd , 4th and 5th units and the mixed bottom ash sample was, respectively, 959, 469, 279 and 491 kcal/kg in dry form, it increased to 2490, 1312, 786 and 1348 kcal/kg in the product obtained as a result of flotation in optimum conditions. Key words: ash, conventional flotation, unburned carbon

Jan 1, 2008

By D. -H. Park, G. -j. Kim, Y. -J. Park, C. -S. Hong, S. -Y. Choo

To evaluate the quantitative tunnel behavior influenced by characteristics of discontinuity, this pa-per executes the parametric study using 2 and 3-dimensional DEM analysis. First of all, this study finds that displacement and the stress of shortcrete are proportioned to frequency of joint and rockbolt axial force is adversely proportioned too. Secondly, it is found that the most sensitive in-put parameter used in Barton-Bandis(BB) model is residual friction angle. Finally, when joint sets are encountered at tunnel excavation face, to identify the most critical joint orientation is very crucial for a stability of tunnel. La thèse a pour but d’étudier les influences sur la stabilité du tunnel, au niveau du réseau de la discontinuité et de la valeur de sa nature aquis par le projet récemment exécuté en vue de mener à l’analyse quantitative de cette stabilité, en appliquant chaque différent paramètre comme la fréquence de diaclase, la constante de résistance des modèles de Barton-Bandis(BB) ainsi que la relation entre le sens d’excavation du tunnel et le réseau de diaclase en 3 dimensions. En fait, cette étude nous a montré que la fréquence de diaclase s’accroît proportionnellement au déplacement et à la contrainte du béton projeté. L’angle de friction résiduel s’est montré le plus sensible à la stabilité du tunnel parmi les modèles de BB. Aussi à travers l’analyse à 3 dimensions, il s’est vérifié que si l’angle de pente du groupe de diaclase est horizontal entre l’axe du tunnel et la direction, il donne une influence importante sur le comportement du tunnel. En particulier, l’influence était la plus importante sur un fond rocheux dont la diaclase horizontale est grande. Um das quantitative Verhalten des Tunnels zu bewerten, eroertert dieses Papier eine parametrische Studie mit Hilfe der DEM Analyse. Auch wird hier eine zweidimensionale Analyse von Ver-bindungen verschiedener Frequenzen in der Gesteinsmasse, eine sensitive Analyse von allen der im Barton-Bandis-Modell (BB) genutzten Parameter und eine Dreidimensional-Analyse mit ver-schiedenen dreidimensionalen geometrischen Veteilungen von Verbindungen ausgefuehrt. Erstens: Die Studie findet heraus, dass Vedraengung und Druck im Shortcrete proportional zur Frequenz von Verbindungen und Axialkraft der Steinbolzen antiproportinal ist. Zweitens: Es wird herausge-funden, dass die am meisten Sensitiven der im BB-Modell angewendeten Eingaben die am Ende uebriggebliebenen Reibungswinkel sind. Und schliesslich wird herausgefunden, dass wenn Ver-bindungsteile an der Tunnelaushoelungsoberflaeche ausgemacht werden, fuer die Tunnelstabiltaet die Identifikation der meist kritischen Verbindungsorientierung sehr bedeutungsvoll.

Jan 1, 2003

By R. Dehghan, M. Zarei, A. Tohry, S. C. Chelgani

Typical depressants for selective reverse flotation of iron oxides from complex silicates do not generally show high levels of efficiency. Therefore, as a hot topic, there are several ongoing investigations in this area. The main aim of this paper is exploring the potential of using humic acid (HA) as a depressant in reverse cationic flotation of hematite from complex silicates. For such a process, the wettability and flotation behaviour of pure minerals (hematite and silicates) was investigated at pH 10 in the presence of HA and cationic collector. Adsorption mechanism of HA on these minerals was measured by zeta-potential and FTIR. Results of flotation tests showed that at the lower concentrations of HA, selective separation of silicates from hematite is beneficial, where the floatability of amphibole was higher than pyroxene. A higher separation efficiency of hematite through reverse flotation was observed in the presence of amphibole, in comparison with the presence of pyroxene. Wettability studies showed that HA has a significant effect on reducing the hydrophobicity of treated minerals with the collector. The adsorption, ZPC and FTIR test results indicated that HA was adsorbed on both silicates and hematite. However, the absorption intensity onto hematite was much higher than silicates. It was found that the adsorption mechanism of HA on hematite takes place through both strong H-bonding and ligand exchange. Keywords: Reverse cationic flotation, humic acid, iron oxide, complex silicates, surface adsorption

Jan 1, 2020

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

By A. F. Silva, R. Dockendorff, J. M. Girao Sotomayor, V. F. Navarro Torres, C. Castro

This paper shows the importance of performing probabilistic analyses in open pits, especially for mine planning, which can lead to more efficient ore extraction and meeting the acceptability criteria for safety in mine slopes. Three-dimensional stability analyses were performed to evaluate the future geometry of a large open pit for iron ore extraction in Brazil. The strength parameters of the lithologies were calibrated using ruptures in the pit walls. After determining the factors of safety (FoSs) from the calibrated parameters, probabilistic analyses were performed using the total range of values of each parameter under different field conditions to verify the reliability of the initial analysis. In this sense, it was possible to plot the probability of failure (PoF) and the FoS on the graph of slope height versus slope interramp angle (IRA) for the future pit in each lithology. IRA recommendations are made for two scenarios: (1) the best scenario: dry without ubiquitous joints and (2) the worst scenario: the water table at 10 m depth with ubiquitous joints in the most unfavourable direction. The results show that probabilistic evaluation is an important tool for establishing alert mechanisms in slopes that can be termed stable.

Jul 2, 2022

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By P. C. Pistorius, M. P. Maphutha, J. D. Steenkamp

Advanced high-strength steels (AHSS) are sophisticated materials being developed by the steel industry to mitigate challenges related to the performance of motor vehicles. To meet the requirements of AHSS, the ferromanganese alloys (FeMn) utilized in the production of the steel are required to contain acceptable levels of unwanted impurities, i.e. P, S, N, H, and C. The focus of the current study was to investigate dephosphorization of ferromanganese to produce a low-P alloy that could be effectively utilized in the production of AHSS. The study involved conducting laboratory-scale testwork to study the efficiency of CaO-based slag systems to dephosphorize FeMn alloys. The addition of Na2O, CaF2, and BaO to MnO-CaO-SiO2 slag was considered. The test work was carried out in a 25 kW induction furnace at temperatures of 1350°C, 1400°C, and 1450°C. The P partition coefficient (Lp) remained small at <1, which is an indication that dephosphorization had not been achieved. The baseline slag, comprising 40%CaO-40%SiO2-20%MnO, reported higher Lp values. Addition of Na2O and CaF2 did not show any further benefit. Substituting half of the CaO by BaO, resulted in similar Lp values to those of the baseline slag under conditions of 1350°C and 1450°C at 30 minutes. In summary, based on the Lp values obtained, the conditions investigated with the CaO-based slags appeared to have been unfavourable for dephosphorization of FeMn alloys, as most of this impurity element remained in the alloy.

Sep 1, 2021

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

By deur R. R. Mears

The expected curtailment of activities within the gold-mining industry by the closure of the more marginal mines, and the shortening of the life of the industry as a whole as a result of rising costs and/or an uncertain gold price, are factors that are bound to harm the South African economy in a number of ways. The industry has no option but to regard the gold price, which is determined on the world market, as a given quantity. The remaining ore reserves al tend to be of a lower grade and/or to be found at greater depth. Therefore tighter control of working costs would seem to be almost the only option open to the industry. Working costs can be divided into two broad categories: costs emanating from the environmental characteristics of the orebody, and costs emanating from the general inflationary environment in which the industry has to purchase its inputs. Working costs stemming from the physical environment also fall into two categories: those relating to the grade of the orebody, and those resulting from working at increasing depth and temperature, together with the need to pump increasing quantities of water. The industry is both capital- and labour-intensive in absolute terms, since it requires large inputs of labour as well as of capital. It is limited in its scope to adjust its production function by becoming more labour- or more capital intensive, and is dependent on a large labour force, which cannot easily be replaced by capital inputs. On the other hand, large amounts of capital are required for investment in shafts, development, machinery, and equipment. Since the early seventies, the working costs of the South African gold-mining industry have increased at an annual rate that was significantly higher than the general rate of inflation. This rapid rise in working costs has caused some mines to find themselves in a difficult profit position. At times, the gold-mining industry has even been compelled to restructure its cost/revenue relationship rather fundamentally by revising the grade of ore worked sharply upwards or downwards, as the case may be. The rise in the gold price since 1972 has made it possible for the industry to introduce significant changes in its Black wage policy. The main aim was to increase the permanency of the Black labour force and to encourage local Black workers to join the industry. At the same time, significant increases were also experienced in the cost of machinery and stores, as well as of capital, mainly as a result of inflation. In the study on which this paper is based, the author attempted to measure the influence of environmental factors on working costs, using the physical consumption of electricity as a criterion for measurement. He found that the usefulness of this criterion in relation to factors such as depth, temperature, and water quantities pumped was invariably more than neutralized by the effects of greater productivity and economies of scale. The effects of these environmental factors on the working costs of the industry could therefore not be determined to any degree of accuracy. It seems that good progress is being made with the development of capital-intensive forms of technology aimed at coping with rapidly rising working costs and other effects of increasing depth. Techniques are also being developed to improve rock-cutting procedures and to eliminate the use of explosives in order to introduce a continuous mining process. On the whole, the gold-mining industry seems to be more sensitive to general inflationary pressures than to the cost effects that are associated with depth, temperature, and water quantities pumped. Greater control is possible over physical environmental factors such as the grade of ore mined, temperature, rate and nature of development of a mine, and adaptation of the daily working cycle to a continuous mining process. Wolfe and others hold the view that the industry will lose control over labour costs as a result of the &apos;sharp increase in wages and the growth of Black trade unions. However, the use of more capital-intensive technology will allow the industry to reduce its labour force, and a smaller, better-trained, and more permanent labour force will enable the industry to cope with the increasingly difficult physical environment and higher wages.

Jan 1, 1987

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021