Search Documents

By R. S. Olsen

The Bureau of Mines is engaged in a continuing research effort toward the recovery of alumina from kaolinitic clay and other nonbauxitic domestic minerals. Hydrochloric acid extraction of calcined clay is among the acid processes under consideration. Although aluminum is easily leached from calcined clay, the presence of fines and slimes in the leached residue has hindered the application of this and other acid leaching processes. A clay feed preparation method was therefore developed that eliminated the slimy nature and the separation problems normally associated with leached clay residues. The preparation process consists of crushing the raw clay to minus 20 mesh, dampening the crushed clay with a fine water mist while tumbling on a rotating disk, and calcining the misted clay at 750° C. The misting process increases residue settling rates threefold to 9 cm/min (18 ft/hr) and filtration rates by two orders of magnitude. Leaching-kinetics were determined for misted clay feeds in a batch, stirred-tank reactor. Rapid leaching occurred during the first 85 to 90 pct of the extraction. The linear relationship of extraction to time during this initial phase corresponded to a zero order reaction with a rate constant of around 10 pct/min.

Jan 1, 1981

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By Blair Burwell

This paper describing the method of mining a deposit of vanadium ore near Rifle, Colo., is one of a series of similar papers on metal-mining methods and costs being issued by the United States Bureau of Mines. This vanadium deposit probably is the largest yet found in North America. It is situated 12 miles northeast of Rifle, Colo. (see fig. 1), on the southern flank of tae White River plateau, and is at an altitude of 6,500 feet. Between 150 and 200 tons of ore are mined daily and trucked to the mill at Rifle. The product of the mill is fined vanadium oxide, which is shipped to the company's plaits at Columbiana, Ohio, and Niagara Falls, N. Y., for the electric manufacture of ferrovanadium. HISTORY The deposit was discovered about 1909 by men prospecting for carnotite. Its outcrop on the bola cliff of Rifle Canon had been known to stockmen for many years.

Jan 1, 1932

By A. R. Elliott

In the early part of the your 1919 the Bureau of Mines undertook a study of methods of handling oil after it had buon produced, with the view of pointing out the losses due to evaporation and other causes. Observations on present methods show that the oil is subject to largo losses in both quantity and quality from the time it loaves tho well until it is recoivod by the pipe-lina company. During this time it is splashed into four or more tanks of various sizes and with little or no protection over the tops. From the settling tank, where the flow of oil is tamporarily stopped in order to permit sparation of ter and sediments, through the gago tanks and leaso gathering tanks to the largo tank storage where it is hold for many days, rich gasoline vapors roadily escape, especially from tho ghor gravity oil. As no effort is made to measure the oil before it reached the storage tanks, where it is delivered to the pipe-line company, the lossos of the light products of the oil can only be approximated, and, as final results will show, are no doubt usually very much underestimated. In conducting this investigation, the Bureau has endeavored to make tests that would show quantities and values lost, in order to impress better upon those concerned what might be saved through a little more diligence. Eperiments were conducted on both California and Mid-Continent oils. The field operimental work done in California, on which a report is to be published in the near future, is cutlined briefly below: The field work consisted in collecting from operating companies data on storage of oils in large tankage and in performing experiments in the field on storing and piping oil to small lease tanks under practical conditions. Acourate Easurements were takon on the volume, gravity and gasoline content of the oil as it passed through the various stages in its removal from the lease. The work extended over the four seasons of the year in order to obtain better the effect of varying winds and high and low atmospheric temperatures during those periods. Thanks are due to the many oil operators who have taken a personal interest in the work and gave valuable information and assistance. One company furnished the oil and tanks and much of the apparatus and labor. This company also per- mitted the work to be done on its properties in the Coalinga field. This was of material aid, as the results were to be comparative and therefore it was necessary that the same gravity oil be used throughout the experiments.

Oct 1, 1920

By C. Travis Anderson

"A recent critical study by Ralston3 of the iron system points out the importance of and necessity for work upon the preparation of ferrous oxide. Not only are ferrous oxide samples desired for determination of the important physical and chemical properties, such as specific heats and heats of formation, bat also information on the stability and behavior of this material is of considerable technical importance. Related. problems where the properties of Fe0 are important have to do with desulphurization of iron, the formation and occurrence of magnetite in copper smelter slags, and sulphur elimination in copperFerrous oxide also has valuable catalytic properties, as is demonstrated in nitrogen fixation.Pure ferrous oxide has never been prepared in quantities large enough to furnish adequate physical and chemical data on its properties. Only two or three experiments4 have produced a fraction of a gram in a state approximating purity and have collected evidence that has been sufficient proof of their having done so. Ferrous oxide is stable only above about 570°C., and below that splits into magnetite and iron according to the reactionUp to about 1920, those who had endeavored to prepare FeO made no provision for rapid chilling, so that although their product. may have had the proper iron oxygen ratio for FeO, in reality it-probably did not consist of pure FeO. The above reaction is reversible; above 570oC. magnetite and iron are supposed to recombine almost completely, and if so, should constitute a direct and easy method of preparation. The data, however, were somewhat conflicting, and the extent to which the reaction goes in either direction needed checking. Preliminary experiments on the interaction of molten Fe304 with solid Fe gave Fe0 of about 85 per cent purity, corresponding to. the approximate purity obtained by some previous investigators. The present work is concerned chiefly with the results cf repeated interaction between partly reduced magnetite and iron, and the calculations which may be made from such results. Repeated treatments are necessary, because molten impure ferrous oxide and iron can not be kept in contact for more than short periods of time."

Oct 1, 1928

By Robert C. Gabler

The extraction of metals from coal ash was investigated by the Bureau of Mines in an effort to produce a more environmentally acceptable waste and offset waste disposal costs with recovered metal values. The research was conducted in two steps: determination of the parameters that affect extraction of metals from coal ash and development of extraction-recovery procedures. Data obtained indicate that the major parameter affecting the extraction of metals from coal ash is the calcium content of the ash. Other parameters such as furnace type and operating temperature had much smaller effects on metal extraction. Two procedures were studied for metal extraction: an acid leach procedure for high-calcium ashes and a lime sinter-acid leach procedure for low-calcium ashes. An alumina product was recovered that, with sufficient washing, meets Hall cell specifications. The leach residues pass the EPA EP Toxicity Test and are thus nonhazardous wastes available for a variety of uses.

Jan 1, 1983

By C. C. Shale

Electrical resistivities for various coal ashes in air and in a nitrogen atmosphere are given over the range 100° to 1,500° F. Resistivity of low-carbon ash in air is very high at low temperature, rises to a maximum at about 250° F, decreases very rapidly with increasing temperature to about 800° F, then decreases gradually to approach an asymptote at 1,500° F. Resistivity of high-carbon ash in air follows this same general trend at values which are much lower and are proportional to the carbon content. After the carbon has been burned off, resistivity of the remaining ash approaches the high values corresponding to low-carbon ash of similar chemistry. Two factorial experiments show the effects of temperature, particle size, chemical content, and compressibility on the resistivities of four fly ashes of widely different chemical composition in the temperature range proposed for coal-fired turbines. Resistivities of all low-carbon ashes tested fall in the range 106 to 107 ohm cm at 1,500° F and should be removable by electrostatic precipitators. Ashes containing carbon in excess of about 8 percent, however, have low resistivity (as determined in nitrogen), especially at high temperatures. Therefore, high-carbon materials may not be collectable in precipitators because the resistivity is below the minimum value necessary for precipitation. Consequently, high carbon residues from partial combustion of coal probably could not be removed effectively at high temperatures.

Jan 1, 1968

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980

By R. L. Grant

At the Eighth International Conference of the Directors of Safety in Mines Research, Sartorius and Thouzea5/ presented and discussed data obtained in explosives tests made under varying conditions of humidity. These tests showed that there was less probability of explosives failure when the humidity of the testing gallery atmosphere was high. As it is to be expected that the relative humidity of mine atmospheres where permissible explosives are used will not be identical with that of the test-gallery atmospheres, the influence of atmospheric moisture upon the incendivity of permissible explosives is of the utmost importance if decreasing humidity reduces the relative safety of an explosive. Because of this and because the question has recurred frequently in discussions of gallery testing at Bruceton, Pa., it was decided to investigate the effect of humidity and ambient temperature on the ignition of firedamp by explosives, applying the small-scale gallery methods developed at the Bureau of Mines and used earlier to study the fundamental causes of such ignitions.6 7 8/

Jan 1, 1956

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report describes the development and application of a rail haulage simulator that is readily adaptable for the analysis of a wide variety of operating problems. Various gaming, options have been integrated into the model structure which permit trial and error solutions from a computer terminal prior to capital committment in the actual operation. The high level of information retrieval available allows engineers and managers to develop production data which fit individual needs. In this report, emphasis was placed on the problem of organizing and performing the sequence of operations that are necessary to accomplish a complete mine materials handling simulation. Here, the Rail Haulage Sub-assembly was linked to the Production Sub-system to mine and move coal from seven operating sections to the intermediate and main-line track. The analysis was devoted to the problems associated with how the operating system performs and what alternatives were available to minimize idle times and hence increase productivity. In order to have some objective means of evaluating which of the alter- native methods for production was most appropriate, the choice was to replace the intermediate track with belt conveyors. Since the attempt here was to demonstrate model flexibility and not to establish the goals or trade-offs between computing objectives with which systems judgement must contend, no further alternatives were tried. This is left to management with the data and a problem to solve. Rail haulage simulation is not new, and several, operationally tested models are being used in practice (Bucklen, et. al., 1968).

Jan 1, 1974

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

By Charles L. Kimbell

Following the pattern established in the 1989 edition of this study, the concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies of any type. As the countries of eastern Europe, including the numerous states that formerly comprised the U.S.S.R., undergo the transition from centrally planned economies' to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeing economic assistance from government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. This situation, coupled with governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national security probably never was really necessary and certainly proved unnecessary with the end of the so-called cold war, has led to the publication of increasing amounts of both statistical and nonstatistical information in the countries undergoing economic transition.

Jan 1, 1993

By G. D. Jermain

Exploration of the Antimony Peak district by the Bureau of Mines was conducted under the authority of the Strategic Minerals Act of 1939. Antimony was one of the seven metals designated at that time as strategic by the Secretaries of War, Navy, and Interior upon advice of the Army and Navy Munitions Board. As a result of many field examinations, the Antimony Peak property was chosen as one of the most attractive for the possible development of emergency antimony reserves. Exploration by the Bureau of Mines began in November 1940 and was concluded in May 1941.

Jan 1, 1949

Improve underground mine roof bolt support systems by alleviating problems associated with certain ground support systems currently being used. Approach Convert a passive resin-grouted roof bolt system into a uniform, tensionable roof bolting system. Background Resin-grouted roof bolts are one of the most common forms of ground support in U.S. underground coal mines. These support systems can be installed with a full-column of grout and be loaded with subsequent roof movements after installation. This is called a "passive" support system. An alternative to the passive support system is the mechanically-anchored, tensioned roof bolt system. This system is installed with resin grout. This system is designed to load or tension the support during installation by using a mechanical anchor, coupling, or threaded nut after the resin has properly cured. It is called an "active" support system and is used extensively for improved strata control in a laminated geologic deposition or in difficult ground conditions. To ensure that active bolts have been properly installed, the bolt loads must be checked by using a torque wrench or other suitable equipment. Unfortunately, this practice presents potential safety hazards and has limited accuracy. Laboratory and field experiments also reveal that the torque-to-tension ratio developed on active support systems can vary by 50% from bolt-to-bolt. Variations in bolt load installations can induce stress concentrations and lead to roof degradation or failure.

Jan 1, 1991

By John M. Gomes

In the repetitive electrowinning of tungsten from scheelite, the calcium impurity buildup in the molten electrolyte results in decreased metal purity, metal recovery, and current efficiency. Periodic addition of B2O3, which reacts with the lime liberated from the scheelite, more than tripled the life of the electrolyte in winning 99.9-percent-pure tungsten and also reduced the number of units of electrolyte required per unit of tungsten recovered from six to four.

Jan 1, 1966

By William R. Sharp

This Bureau of Mines report details a technique for aiding the engineer with the long-range design of an underground mine. The method is based upon the assumption that sufficient data are available to assign numeric values to some finite number of mineralized blocks; assignment of numerical values is problem dependent. By assigning appropriate weighting schemes, the algorithm developed in this report may be used to solve the optimal end-of-life underground mine layout, design least-cost electrical layout networks and efficient material handling networks, find least risk escape routes in the event of an accident, etc. The method is based upon the assumption that sufficient cost and geologic data is available to build a detailed mineral block inventory of the mineral deposit. It is further assumed that the cost assigned to any minable unit is independent of the neighboring blocks. The basic approach relies upon concepts and ideas from the theory of networks. To make the approach user oriented, a computer program is included and discussed. The computer code is written for an orthogonal, three-dimensional set of blocks. Computational costs and experience indicate that the program could be of great benefit in evaluating large complex mineral properties from the viewpoint of predesigning an underground mine layout.

Jan 1, 1974

By W. P. Diamond, B. M. Bench, C. M. McCulloch

This Bureau of Mines report describes photolineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W - N 15° E, and N 57° W - N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W - N 20°E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W - N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977

By M. M. Fine

In an experimental study by the Bureau of Mines, in cooperation with National Lead Co., the roast-flotation process was found to be an effective means of upgrading certain cobalt-nickel stockpiles. The research was undertaken to determine whether the process could yield an enriched feed, with a minimum cobalt content of 6.0 percent, for the company refinery. The stockpiles (products of the company Fredericktown, Mo., milling operations) were essentially complex sulfides of cobalt, nickel, copper, lead, and iron, 1 sample of which contained 2.84 percent Co and 3.57 percent Ni. After a controlled oxidizing roast at 400° C., laboratory flotation with conventional sulfhydric reagents yielded an enriched concentrate analyzing 9.22 percent Co and 11.43 percent Ni, with recoveries of 84.9 and 85.8 percent, respectively. These are typical laboratory data; other data indicated higher grades were possible but at reduced recoveries. A brief, continuous campaign verified the applicability of the process to the raw material in question but was not continued long enough to establish optimum conditions. As a consequence, the results of the large-scale tests did not equal those obtained in the laboratory but definitely confirm the beneficiation possible from the roast-flotation process.

Jan 1, 1958