Search Documents

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By Leonard Greenburg

The analytical procedure necessary when using this new impinger•bubbler eil)paratus is almost identical with that em:r;,loyed with the Palm0r a:pp8.ratua. As sugar is not employei, the new apparatus por.;sesses the advantage over the eug.r tube method in having vsry low control errors, being, therefore, much simple in laboratory manipulation during analysis.

Aug 1, 1922

By J. Nielen van der Merwe

For the last 3 decades, coal pillars in the Republic of South Africa have been designed using the well-known strength formula of Salamon and Munro that was empirically derived after the Coalbrook disaster. The database was recently updated with the addition of failures that occurred after the initial analysis and the omission of failures that occurred in a known anomalous area. An alternative method of analysis was used to refine the constants in the formula. The outcome was a new formula that shows that the larger width-to-height ratio coal pillars are significantly stronger than previously believed, even though the material itself is represented by a reduced constant in the new formula. The formula predicts lower strength for the smaller pillars, explaining the failure of small pillars that were previously believed to have had high safety factors. Application of the new formula will result in improved coal reserve utilization for deeper workings and enhanced stability of shallow workings.

Jan 5, 1999

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

By Robert L. Lagace, N. Albert Moussa

The objective of this project was to perform a preliminary study to determine the desirability/practicality of burying the communication cables in underground mines in order to protect then from the effects of fires and explosions We conducted discussions with Government and industry specialists on the physics of mine fires and explosions, mine disaster fighting, rescue, and investigation activities, and on nine operations. In addition we examined published experimental work and selected detailed NSHA accident reports on fires and explosions in underground mines. We found the overall desirability /practicality of cable burial must be regarded at this time as highly questionable, because of its benefit limitations to special sceneries, its practical operational shortcomings, and the availability of alternative cable protection options.

Jan 2, 1982

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they're doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

Assure fail-safe stopping of a mining vehicle immediately following a loss of electric power. Approach A separate emergency brake system which actuates when electrical power is interrupted, was installed on several mining vehicles and tested in a long-term underground mining demonstration. How It Works Separate, spring-actuated brakes, which press against brake discs, are used to stop the vehicle following power failure. To allow norm al movement of the vehicle, hydraulic oil under pres? sure from the vehicle's hydraulic system is directed to a spring? loaded piston in each emergency brake housing. That pressure causes the piston to compress the spring and relieves the spring pressure against the puck, thereby allowing the brake disc to turn freely. See Figure 1 A. If the electrical power fails or if the machine is turned off, a valve in the hydraulic line to the emergency brakes opens. That valve, shown as ?Solenoid Valve (automatic)" in Figure 1, which is normally held closed by its electrical solenoid while the vehicle is electrically powered, is opened by the spring in the valve assembly. The pressure in the hydraulic line which is connected to the emergency brakes then drops to

Jan 1, 1978

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By J. E. Zeilinger

The technical feasibility of using energy from explosive ignitions of coal dust to pump water was .demonstrated in an exploratory investigation. Ignition of small amounts of pulverized coal that were dispersed in air over columns of water pumped up to 5.3 gallons of water per cycle when operated against a head of 30.75 feet. Water displacement was accomplished by either manual or automatic operation through a single cycle, and by automatic operation through a continuous series of cycles of I-minute duration. Operating through single cycles, slurries containing up to 3 pounds of coal and 4.6 gallons of water were also pumped. Possible uses of an efficient coal-fired pump would include pumping water for irrigation purposes, removing water from mines, transporting coal from mines in the form of a slurry, and pumping water to elevated reservoirs at electric powerplants so that it could be used to generate electricity during peak periods of demand.

Jan 1, 1966

By Gordon H. Dechman

This Bureau of Mines report presents an iterative approximation method for microseismic source location that was developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems, such as slope failure in an open pit mine. The source location method and two derivative location algorithms are described in detail, and the speed and accuracy of the two algorithms are compared.

Jan 1, 1977

By Wilbur I. Duvall, Thomas C. Atchison, David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain en- ergy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy E/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form Analysis of the data showed that the intercept parameter H depended upon the type of explosive used but that the absorption coefficient B was practi- cally independent of the type of explosive. Comparison of the intercept pa- rameter H and the calculated energy of the explosive showed that the percent- age of explosive energy transferred to the rock increased linearly as the ratio of the characteristic impedance (product of density and propagation velocity) of the explosive to that of the rock increased toward unity. From 5 to 9 percent of the calculated total energy released by the explosive was transferred to the rock as radial strain energy.

Dec 1, 1959

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

By John J. Sammarco

Mining, traditionally a low-tech industry, is now utilizing surprisingly complex programmable electronic (PE) systems. The functional safety of PE-based mining systems is an international issue and concern. From 1995 to 2001, there were 11 PE-related mining incidents reported in the U.S. and 71 PE-related mining incidents reported in Australia. These incidents are due, in part, to unprecedented levels of system complexity. The National Institute for Occupational Safety and Health (NIOSH) is addressing this issue of system complexity by conducting research to develop a quantitative complexity assessment methodology based on Normal Accident Theory (NAT). The methodology models the behavioral interactive complexity at the level of system requirements. A graph-theoretical approach is used for creating quantitative metrics from Software Cost Reduction (SCR) dependency graphs. This complexity assessment methodology will help realize simpler, safer systems that will be easier to validate and verify. The methodology will benefit mining and other industries as well.

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By Mark A. Ackerson, Kenneth E. Hjelmstad

An ideal fire warning alarm system for underground mines would be low cost, convenient, fast, reliable, and able to warn all underground workers. Present warning systems, such as phones, messengers, and stench, fail one or more of these criteria. The U.S. Bureau of Mines may have devised the ideal system. The one way communication system employs a large loop antenna and transmitter to create a 630 hertz (Hz) electromagnetic field to send information through-the-earth to cap lamp battery mounted micro- receivers worn by underground miners. Field tests of prototype equipment in 1986 resulted in through-the- rock signal transmission of over 762 m (2500 ft). Subsequent hardware upgrades for more recent tests resulted in transmissions of over one mile. Recently developed receiver circuitry employs phase- locked-loop detection circuitry responsive only to a specific series of pulses of given time duration, that eliminates false alarms from electromagnetic noise emitted by mine equipment, power lines, or lightning. A multichannel system can relay standard messages to miners

Dec 1, 2007

By R. W. Dalzell, Fred N. Kissell, J. L. Banfield, M. G. Zabetakis

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research