Search Documents

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982

By E. W. Dean

The Bureau of Mines is engaged in the work of obtaining data regarding the physical and chemical properties of typical crude oils from the various producing fields of the, United" States. Preliminary reports have been published that cover the eastern fields* and the' Rocky Mountain districts.** Since the appearance of these, reports: it has been suggested that certain additional data. I regarding the samples would be of practical value. It was believed that a knowledge of the viscosity of crude oil was desirable, particularly in connection with the design and operation of pipe lines. In accordance with this suggestion, the authors have made viscosity tests upon as many of the samples of the two series as wore still available for examination. Determinations were made at temperatures of 70° and 100°F., and in addition the oils were Subjected to the A. S. T M, pour-test*** to as certain the lowest temperatures at which they remain in a fluid condition.

Jan 1, 1921

By Dana Reinke, Launa Mallett, Michael J. Brnich

Some segments of the mining industry, especially underground coal, have seen a large influx of inexperienced miners in recent years. It is anticipated that this trend will reach other mining segments over the next 10 years. This paper discusses the training needs of the younger generation of inexperienced workers who have just entered or are soon to enter the mines. Currently, many trainers are of the so-called Baby Boom generation. Can these different age groups learn to communicate across the generation gap? Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these new trainees.

Jan 1, 2002

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By T. H. Jeffers

Significant amounts of cobalt, a strategic and critical metal, are present in readily accessible spent copper leach solutions. For example, recovery of cobalt at two major u.S. copper operations could produce about 1,300,000 lb Co annually, about 13 pct of domestic consumption. However, techniques such as solvent extraction and precipitation have not proven cost effective in separating and recovering the cobalt from these low-grade domestic sources. The Bureau of Mines has devised a procedure using a chelating ion-exchange resin to extract cobalt from a pH 3.0 copper leach solution containing 30 mg/L Co. Cyclic tests in 4-ft-high by 1-in-diam columns gave an average cobalt extraction of 95 pct when 65 bed volumes of solu-tion were processed at a flow rate of 4 gpm/ft2 of resin area. After an impurity scrub, eluates contained, in grams per liter, 0.4 Co, 0.2 Ni, <0.001 Cu, 1.3 Fe, 2.8 Zn, and 0.008 AI. Solvent extraction procedures to remove impurities, reject nickel, and concentrate cobalt produced a cobalt sulfate solution containing 80 g/L Co, 0.05 g/L Ni, and not more than 1 mg/L Cu, Fe, Zn, or AI. Based on data from commercial electro-winning operations, this solution appears suitable for production of metallic cobalt.

Jan 1, 1985

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

By C. A. Herbert

"Haulage accidents usually are responsible for about 17 or 18 percent of all coal-mine fatalities and about 21 percent of all non-fatal coal-mine accidents. When the relatively small number of employees continuously exposed to haulage hazards is considered, it would appear that haulage is more hazardous than any other phase of coal-mine operation.Haulage accidents have increased from year to year, doubtless due to the increase in electrical haulage, and particularly to the use of larger cars, heavier locomotives, longer hauls, and greater speed. Unless very definite steps are taken to eliminate the causes of these accidents, they will continue to increase rather than be reduced, as they can and should be.Underground haulage in many of the large modern mines of today is similar in many respects to railroad practice. In recent years the railroads have made wonderful strides in reducing accidents, and instead. of being one of the most hazardous occupations, as it once was, railroading is now one of the safest. Doubtless, if thought and action, similar to that given to reducing accidents among railroad passengers and employees, were given to safety in mine haulage, under¬ground haulage accidents could be reduced in about the same ratio.Haulage accidents may be classified, according to responsibility, into two groups - those for which management is largely responsible and those for which the employee is largely to blame; there is, however, an overlapping of responsibility from one group to the other. If, therefore, haulage accidents are to be reduced, it is absolutely essential that both management and employees cooperate to this end.In the first group, for which management is largely responsible, may be included accidents due to faulty equipment, moor track, a poorly arranged system of haulage, lack of clearance or of overhead protection, and dirty roadways; even in these features, however, the employee is not without a measure of responsibility, as failure of haulage equipment possibly may be due to lack of care on his part, failure to report when equipment is out of order, or failure to do a good workmanlike job of installing or repairing or operating.To the second group of accidents for which the employee may be largely responsible, belong those caused by such careless practices as jumping on and off fast-moving trips, coupling on the ""fly"", running at excessive speeds, failure to properly block cars, and similar hazardous and unnecessary acts of omission or commission. If, however, management condones such practices, or, as in some instances, insists upon them, it must accept its share of responsibility for the accidents that inevitably result.Some of the most prolific sources of haulage accidents will be discussed briefly, together with the steps that may be taken to minimize their occurrence."

Oct 1, 1939

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material&apos;s elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

By Eric Cather

A mineral investigation of prospects in the Sawtooth Mountains B Wilderness Study Area (WSA) by the U. S. Bureau of Mines in 1983 revealed none had mineral production, resources, or development potential. The area is underlain by tonalite and smaller amounts of schist, One developed prospect and one prospect pit are in the WSA. They are in schist similar to host rock which has yielded gold in nearby mining districts, Sand and gravel deposits in the WSA are large but too far from markets to be considered resources. No energy (oil, gas, coal, or geothemal) resources were identified in the USA.

Jan 1, 1984

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By Louis D. Dornetto

The effects of electric shocks on man are an important factor in the design of power systems and protective devices. The current levels just below let-go and just prior to the onset of ventricular fibrillation must be known and taken into consideration in the design of power systems and protective devices. Isolated (ungrounded) electrical distribution systems are compared with resistance and solidly grounded systems. The advantages and disadvantages of each are discussed and recommendations are made. Transients on coal mine power systems are a problem that, until recently, have been ignored. Transient voltage levels that can be expected on both the high and low side of the load center and the effects of transients on electronic equipment and personnel are covered.

Jan 1, 1975

By C. L. Karr

The U.S. Bureau of Mines is optimizing the design of an air-sparged hydrocyclone. This report summarizes the initial stage of the project-the prediction of collision efficiencies for use in a comprehensive air-sparged hydrocyclone model. The equations of motion are presented in nondimensional form and solved numerically for a small spherical particle passing around a larger bubble in an infinite fluid under the influence of a strong force field. Collision efficiencies are determined from the calculated particle trajectories for values of Stokes&apos; number, K, between 0.01 and 100 and for values of the nondimensional force, W, between 0.0 and 100. These large values of K and Ware needed to model high-performance flotation devices like the air-sparged hydrocyclone; solutions for the required K and W values have not appeared in the literature prior to this study. Effects of changes in particle-to-bubble radius ratio are considered for both viscous and potential flows. The results help predict the improved recovery of fine particles when flotation is performed in a strong force field.

Jan 1, 1990

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center&apos;s investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By John P. Gooch

Data for the ternary phase diagram for the system 1,1,2,2-tetrabromoethane/water/2-propanol at 25° C have been measured. Experimental methods used are described, and the complete ternary phase diagram is presented. A simple example is given to review the use of the ternary diagram.

Jan 1, 1972

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown&apos;s run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the&apos; main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972