Search Documents

Improve the dust-control effectiveness of the Rotoclone1 dry-dust collection systems used on surface coal mine drills.

Jan 1, 1994

By Charles D. Martens

Raw non fuel minerals produced in the United States during 1981 had an estimated value of $25 billion, about the same as that of 1980. In terms of 1980 dollars. the value of minerals produced during 1981 was $23 billion.2 This chapter includes tables for 1980 that were not available for publication in the 1980 Minerals Yearbook, but does not include the corresponding tables for 1981. The underlying causes of the overall decline in U.S. nonfuel mine production during 1981 were varied, but the common factor was the worldwide recession. In some cases the decline was traced to foreign competition. For example, iron ore production was lower in part because of increased imports of steel products such as coiled steel sheet. Another problem experienced by the domestic mining industry was the continuing difficulty in attracting capital. This was due in part to the attractiveness of investments outside the mining industry, such as short-term, high-interest securities. Another reason was the importation of commodities from countries where overall costs were lower because of such factors as high ore grade, lower taxes, lower wages, government subsidies, and less stringent safety and environmental regulations.

Jan 1, 1982

By Jerry E. Olson

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied additional areas, encompassing 11,303 acres, on the east and west sides of the 20,727-acre Badlands study area (Olson, 1987) in order to evaluate their identified mineral resources. The Badlands study area additions are located in Crook and Deschutes Counties, OR, about 10 and 18 miles east of Bend, OR. No mineral resources were identified. The additional areas studied are underlain by Tertiary-and Quaternary-age basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, mining claims or mineralized areas occur within or near the Badlands study area additions. Slab lava of marketable grade and quantity was not found in either area. None of the study area is of current interest for geothermal resources, but the eastern study area addition has been leased (1984) for oil and gas.

Jan 1, 1989

By A. W. Deurbrouck

Four samples of Pittsburgh-bed coal, of various size consist and ash content were dewatered in a pilot-size vacuum-disk filter partially enclosed with a steam jacket. Steam fed at 2.5 to 12.5 pounds per minute reduced the moisture content of the filter cakes from 2.8 to 13.8 percentage points more than normal vacuum dewatering. Approximately 1.5 pounds of steam was required to remove 1 pound of water.

Jan 1, 1966

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By Robert M. Cox

The U. S. Bureau of Mines (USBM) MULSIM/NL modeling technique has been used to analyze anticipated stress distributions for a proposed alternative longwall gate road design for a western Colorado coal mine. The model analyses indicated that the alternative gate road design would reduce stresses in the tailgate entry without increasing stresses in the headgate entry. To test the validity of the alternative gate road design under actual mining conditions, a test section of the alternative system was incorporated into a subsequent set of gate roads developed at the mine. The alternative gate road test section was instrumented with borehole pressure cells, as part of an ongoing USBM research project, to monitor ground pressure changes as longwall mining progressed. During the excavation of the adjacent longwall panels, the behavior of the alternative gate road system was monitored continuously using the USBM computer-assisted Ground Control Management System. During these field tests, the alternative gate road system was first monitored and evaluated as a headgate, and later monitored and evaluated as a tailgate. The results of the field tests confirmed the validity of using the MULSIM/NL modeling technique to evaluate mine designs.

Jan 1, 2010

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By Robert A. Jankowski

"Following passage of the Coal Mine Health and Safety Act of 1969 (Public Law 911173), the Bureau of Mines initiated a research program aimed at controlling respirable dust exposures of coal mine workers. Respirable dust is the dust that gets into, and interacts with, the lungs of those who inhale it. It has long been recognized as a severe health hazard to mine workers. This program has been implemented by a team effort consisting of the Bureau's in-house capabilities, the Generic Center for Respirable Dust, and contractors, as necessary. Over the years, Bureau research has addressed principally three areas:o Compliance with the Federal 2.0 mg/m3 dust standard (1970-76).o Dust control for longwall mining (1976-1983).o More stringent respirable dust standards due to quartz dust (1983-1987).In addition, fundamental studies have been conducted by the Generic Center for Respirable Dust, with emphasis on penetration of dust into the lung. Accomplishments have been significant, but problems remain, as noted later.The Coal Mine Health and Safety Act of 1969, established a 2.0 mg/m3 dust standard for all coal mining operations, underground as well as surface. At the time of enactment of this legislation, the industry was averaging approximately 4.0 mg/m3. The Bureau of Mines respirable dust research program played a significant role in identifying and developing effective technology to allow better compliance with this new standard, thanks to industry implementation and Federal enforcement."

Nov 1, 1988

By Xavier B. Starnes

"SUMMARYThe J. D. Price property is in Crittenden County, Ky., about 5-1/2 miles west of Marion. The Levias-Crittenden Springs fault system traverses the property. Mines on 3 miles of the same fault system immediately northeast have produced about 250,000 tons of fluorspar ore. The Keystone property, adjacent on the northeast, has produced about 150,000 tons of ore. 3/About 1934, lessees, sank a shaft upon the Price property to a depth of 111.5 feet and crosscut from the bottom of the shaft to the principal fault. No ore was found. Later, in 1942-43, they explored the same fault by core-drilling, but this project also was unsuccessful in finding ore.The author visited the property in September 1944, and subsequently the Bureau further explored the property by core-drilling three holes. No ore was found.ACKNOWLEGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. This ex¬ploratory project was under the general supervision of E. D. Gardner, regional engineer of the Central Region, and 0. M. Bishop, district engineer, Bureau of Mines. The mining branch is under the direction of L. B. Moon. The work on the project was under the direct supervision of Xavier B. Starnes, mining engineer."

Jun 1, 1947

By C. E. Hennig

On January 1, 1960 there were 310 petroleum refineries in the United States, with a crude-oil capacity of 9,901,424 barrels daily, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents a net decrease of three in the number of refineries and an increase of 81,578, barrels per day in crude-oil throughput capacity. Continuing the trend to fewer units with greater individual throughput, the capacity of the average refinery in the United states increased during 1959 from 31,373 barrels per day to 31,740 barrels per day. Compared with the previous year, total crude-oil capacity of refineries on January 1, 1960 was lower in the Appalachian No. 1, Other Rocky Mountain, and Texas Gulf refinery districts. All other districts showed slight increases in capacity. At the beginning of 1960 the industry had under construction facilities that would increase the crude-oil capacity in the United States by 70,947 barrels per day. This was the smallest capacity increase under construction at the beginning of the year since 19460 Included in this construction of additional capacity were two new refineries, one in Michigan and another in Hawaii. In addition, the industry was constructing facilities to replace 50,250 barrels per day of existing crude-oil capacity.

Jan 1, 1960

By W. C. Wahl, M. M. Fine

Leonardite , a naturally occurring , partially oxidized form of lignite with a high content of humic acids , was investigated as a binder for iron ore pellets . Although insoluble in original condition , leonardite forms watersoluble salts with good binding properties when treated with certain alkalis such as sodium hydroxide . Soluble leonardite imparts excellent dry strength to pellets , but green strength is somewhat lower than that obtainable with bentonite . However , green strength can be improved by adding a small amount of calcium hydroxide to the leonardite - concentrate mixture . Leonardite binders were used successfully on three of the four different concentrates tested .

Jan 1, 1964

By L. W. Brandt

As part of its objective to expand the body of mineral information as a basis for new technology, the Bureau of Mines conducted research on the fundamental behavior exhibited by phosphate clay waste in settling ponds. A semiempirical equation used to describe the compaction of ceramic powders in a single-acting die was applied to aqueous phosphatic clay waste and attapulgite slurries. This equation, [*V = a1 e ?k1/P + a2e ? k2/P] was found to describe the compaction of an attapulgite gel and a phosphate slime gel by a moving screen. [*V] is the ratio of the compaction achieved at a given pressure, P, to the compaction achieved at a pres-sure sufficient to remove all space between particles. The constant al represents the fraction of compaction achieved at low pressure by rearrangement of floes to higher packing density, and a2 represents the fraction of compaction achieved at higher pressure resulting from removal of voids within floes. K1 and K2 are constants determined from the experimental data. Both the low-pressure and high-pressure compaction mechanisms were observed in the compaction of the clays. These two compaction mechanisms offer an explanation for the observation that impounded slimes initially dewater rapidly and then dewater at a much slower rate.

Jan 1, 1982

By James D. Sisler

Location and Age The main bituminous coal field of Pennsylvania lies in approximately twenty counties west of the mountain area which extends in a northeast southwest direction through the central part of the Commonwealth. The coal fields lie in a dissected peneplain, still in the youthful stage of erosion There are numerous V shaped valleys in the bituminous fields and the tributaries of the larger streams have rather steep gradients The main streams flow in rather narrow valleys with comparatively small flood plains. The coal beds of Pennsylvania are of Carboniferous age, and are confined to two systems, the Permain and the Pennsylvanian The latter system is divided into an upper or Pittsburgh series and a lower of Pottsville series The Peimain system is divided into an upper and lower series The Pottsville series of the Pennsylvanian is represented in western Pennsylvania by the Upper Pottsville only The upper or Pittsburgh series of the Pennsylvanian is represented by the Monongahela, Couemaugh, and Allegheny groups Geologic Structure. The rocks of the bituminous coal fields are folded into many anti clines and synclines extending in a general northeast direction across the western part of Pennsylvania The intensity of this folding in creases toward the mountain region West of Chestnut Ridge, which is in Fayette, Westmoreland, and Indiana counties, the folding is minor, and the coal beds have low dips East of Chestnut Ridge, v here folding is stronger, the basins are wider and the coal beds rise steeply on the flanks of the anticlines Geology. The bituminous coals of Pennsylvania are associated with shale, sandstone, clay, and limestone Each group has different proportions of these deposits, and the proportions vary at different localities within the same group.

Jan 1, 1928

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.2 The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; 1960, 5.3 feet; and 1965, 5.2 feet.3 Table 1 includes data on number and production of bituminous coal and lignite mines classified by 1-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, 1960, and 1965. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness--less than 2 feet to more than 50 feet--a large majority of the production, 62 percent in 1965, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1967

By Andrew M. Leszcykowski

The Bureau of Mines (Bureau) conducted mineral investigations of the Payette Crest-South Fork area in west central Idaho near McCall, Idaho, in 1989. There are no known producing mines or mineral production from the area. Forty-seven samples were taken (stream sediment, rock. and placer); no identified mineral resources were delineated.

Jan 1, 1991

By Stephen Utter

This report summarizes the procedure and results of an investigation to determine the stresses in the rock around an underground opening in the Climax molybdenum mine, Climax, Colo. This study is part of an overall investigation conducted by the Bureau of Mines to determine the stresses induced by block-caving mining. The purpose of this study is to obtain estimates of the magnitudes and directions of the principal stresses, the location of the maximum stress concentrations, and the effect of topography on the stresses.

Jan 1, 1962

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By R. V. Ramani, V. T. Burgos, J. A. McClay

Model testing is a two part operation; first, to assure the valid¬ity of the mathematical statements and second, to evaluate the accuracy of the computer model for predictive purposes. Verification of both the conceptual and computational aspects can be achieved through the use of input data for which output results are available for comparison. In this dissertation, two test problems were selected for model testing from the Economic Evaluation Reports of the U.S. Bureau of Mines, Process Evaluation Group. Verification Data Set I Input data for this test was selected from an economic analysis of a hypothetical 1,056,000-ton-per-year mine in a 48-inch bituminous coal seam (Process Evaluation Group-Report No. 72-27, 1972). The mine was scheduled to operate five days per week, three shifts per day, 220 days per year with an estimated life of 20 years. Coal reserves covered an area of 6.4 square miles with an expected recovery rate of 70%. Production was achieved through 4 continuous miner sections with an average production rate of 400 tons per shift. The cost summary in the report included a breakdown of equipment and labor requirements. A depreciation schedule listed the expected capital expense per year of operation, assuming capital replacement with identical units and no change in the unit cost. Supply and oper¬ating costs were listed in both gross annual figures and cost per ton of production. The operating and investment costs were projected over the 20 year mine life and a discounted cash flow analysis performed to determine

Jan 1, 1975