Search Documents

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By W. R. ARGYLE, R. A. SHERMAN, Henry Kreisinger, John Blizard, B. J. CROSS, A. R. Mumford

On entering the World War the United States was confronted with the necessity of building in a short time a large number of ships of tonnage adequate to transport troops and war materials to Europe and to carry food supplies to the allied countries, whose merchant fleets had suffered greatly by submarine warfare. The necessity of building ships quickly led to the formation of the United States Shipping Board, which was charged with the duty of developing an efficient organization for the purpose. Such an organization was developed under the name of the Emergency Fleet Corporation; it was under the control of the Government, but could conduct its business in the most direct way, like a private corporation. In order to build the largest- number of ships possible without drawing too heavily on the steel industry, which was already taxed heavily by the production of munitions, it was decided to build wooden as well as steel ships. These ships were built from a few standard designs to enable a large number of duplicate parts to be fabricated in inland shops and transported by railroad to the shipyards on the seacoast, where they were assembled into ships. In other words, the plan was to manufacture the ships rather than to build them. The shops on the seacoast were reserved to make those parts of the ships' equipment that could not readily be transported. The inland shops made the parts that could be transported to the seacoast by railroad. Among the more important parts of the ships' equipment to be standardized were the boilers. As the Scotch marine boiler in large units is bulky and can not be transported by railroad, and as, for the same capacity,much more steelis needed in its construction than for water-tube boilers, a few simple designs of water-tube boilers were developed that inland shops having ordinary equipment could make in large quantities.

Jan 1, 1924

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

By Francis E. Federspiel

A mineral purvey of the Granite Chief RARE II area (A5-261), covering about 23,400 acres (9,470 ha) of Tahoe National Forest and the Like Tahoe Management Unit, was conducted by the U.S. Bureau of Mines and the U.S. Geological Survey in 1979 and 1980 (fig. 1). The investigation by the Bureau of Mines indicates that the area has a low potential for mineral resources. Samples taken from prospect pits and favorable outcrops indicate no minable quantities of precious or base metals. Placer deposits are too small and low grade to be considered a resource.

Jan 1, 1981

By J. C. Fowler

[This i.untra t hds bmii III c'IIILt fur till- past 1':?:u yrlr;, Till-- wurir pnrfor rw:it '. ,JS hlui.rn dawn Ilttf lit Iu i eel i ih?IS( S. 1 hesrt aIII, Phase I Candor tlri I a lest It) donurnSlrale SeiSrrlir nurihudS to hu USi!d lot ttlr? rti?tei thin and Iu" ainnl ul trapped rrlinc:rs hitting (-)it the roof with a harnrner, Phase I' Design and cunStrur.t a permanent Seismic monitor System to rrlunrtur roof (ails arm r:xploslun', III ,r 'Vol king mine. Phase III - Ire dII an an i i irr for sVstl rtl Ii i`'Smltur air quality in till, niitii iiH II ? ir,iti tin; niln !III ;I I ,, i; Phase I V - Conduct 11(21 d tests of the seismic IT IUnit UT ieq system fur a period nl two 11IUIIIIIS. Phase, V - Condirct three test periods of the seismic system over a period of six mimilis. Detailed reports covering the wurk. done in Phases I, 11, and IV have been i : . r tr I - i t report will, therefore, cuni.entrate on the work perfurmed in Phases III anti V.]

Jan 1, 1975

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

By J. B. Elizondo

This paper, which describes mining methods and practices at the Piokee mining unit and the Piokee expertmental mining project of The Eagle-Picher Co. in northeast Oklahoma, is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Piokee unit, comprising the Piokee, Rowe, Lucky Syndicate, and parts of the Netta White and Otis White leases, is in the SW1/4, W1/2NW1/4SE1/4, and W1/2SW1/4SE1/4 sec. 17, T. 29 N., R. 23 E., Ottawa County, Okla. (figs. 1 and 2), The 200-acre tract is adjacent to the town of Picher and near the heart of the Picher field of the Tri-State zinc-lead mining district.

Jan 1, 1959

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers' state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers ' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

By Russell A. Schreiner

In conjunction with the Geological Survey, the Bureau of Mines conducted a mineral investigation in 1981 and 1982 of the Santa Rosa Mountains Wilderness Study Area (WSA), Riverside County, California. The Bureau of Mines is responsible for the mineral survey of mines, prospects, and mineralized areas in and near the WSA. A literature search was completed to obtain information concerning mineral occurrences and mining activity that relate to the WSA. A field investigation inside, and up to 1 mi outside, the boundary of the WSA, disclosed one prospect. This prospect was surveyed by compass and tape, and five samples were taken to determine the representative mineral content. No attempt was made to expose concealed mineralization or to re-open caved workings. All five samples were analyzed by fire assay for gold and silver and by colorimetric methods for tungsten. Two of the samples were analyzed by semi quantitative spectrographic methods to determine if any unsuspected elements were present. All analyses are furnished in this report except for the semi-quantitative spectrograhic analyses. Complete sample analyses are available for public inspection at the Bureau of Mines, Intermountain Field Operations Center, Building 20, Denver Federal Center, Denver, CO 80225.

Jan 1, 1983

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By Pedro Lilienfeld

This report presents a design and cost investigation for several alternative versions of a field-worthy mining machine-mounted respirable dust monitor. Three main design variations are considered: (a) light scattering sensing, (b) Beta-filter tape sensing, and (c) a combination of the two preceeding methods. Eventual instrument production coats as a function of design complexity are tabulated. Cost estimates for the development and field testing of field-worthy prototypes are also presented. A general discussion on the technical aspects of these design alternatives is included following a modular-hierarchical approach of progressive complexity. The technical background to this report has been provided by the experience and results derived from the work performed under U.S. Bureau of Mines Contracts Nos. H0166097 and H0377092.

Jan 1, 1980