Search Documents

By S. L. Windes

"INTRODUCTION For a number of years, the Bureau of Mines conducted tests on various types of structures to ascertain the effect of seismic vibrations emanating from quarry blasting in an effort to determine an index of damage. Associat¬ed with these tests, occasional records were made of the characteristics of the air blast or concussion from the explosions. Although the importance of the air-blast problem was recognized, the equipment was not designed for airblast measurements, nor was the early research program concerned with the problem. After the ground-vibration tests had been completed, attention was turned to study of the air blast and its effect. The program was modified, however, in certain aspects by the imminence of war and the final entry of the United States into the conflict. These modifications were made to supply information pertaining to military and civilian defense problems.Detailed discussion of these problems is beyond the scope of this report, which attempts to present preliminary results of factual and fundamental character. However, it may be noted that airblast data are urgently needed for intelligent design of both Government and non-Government buildings, which must withstand the air blast from bombs and afford maximum protection for the occupants. The safety of vital equipment above and below ground necessitates consideration of damage from air blast. Protection against use of dynamite by saboteurs, moreover, hinges largely on the effect of air blast. Identification of a planned ""accident"" involving dynamite often entails knowledge of the characteristics and power of the airblast.The peacetime problem of damage from air blast resulting from quarry and mining blasting activities is of course exaggerated by the wartime requirements of increased production accelerated operation, and enlarged development."

Jun 1, 1943

By A. L. Foote

This is the final report of work accomplished during 1973-75 under U. S. Bureau of Mines Contract No. H0242015, "System for Handling Underground Mine Supplies and Materials." The purpose of the contract was to develop a mechanical device which could safely perform handling tasks that are normally done manually in underground bituminous coal mines. The report discusses studies leading to construct-ion of a battery-operated, three-wheel vehicle with a six-degree-of-freedom manipulator. Supportive design studies included collection and analysis of production, manual functions, and injury data on the underground bituminous coal mining industry. Transfer tasks in section storage and working places were the prime candidates for mechanical handling. Functional specifications were developed for two handling devices (one to handle existing unit loads and one to handle repackaged unit loads) and for a vehicle to mount the handling device. Design concepts for nine different handling devices were developed and a cost/benefit evaluation made for each. Detail design, capital and operating costs, and method improvement savings data were developed for two battery-operated vehicles and for two different manipulators. The three-wheel vehicle with anthropomorphic manipulator was chosen for development.

Jan 1, 1978

By B. J. Moore

This Bureau of Mines publication estimates that U.S. helium resources as of January 1977 were 710 billion cubic feet. These resources are broken down into four classifications, as follows: Helium in measured natural gas resources and in storage, 201 billion cubic feet; helium in indicated natural gas resources, 150 billion cubic feet; helium in hypothetical natural gas resources, 175 billion cubic feet; and helium in speculative natural gas resources, 184 billion cubic feet.2 Most of the helium in natural gas is presently dissipated as natural gas is consumed as fuel and for other purposes. Helium resources of the United States may also be divided into three other categories: (1) Depleting and undiscovered natural gas resources, 589 billion cubic feet; (2) nondepleting natural gas, 83 billion cubic feet; and (3) storage, 38 billion cubic feet, of which 37 billion cubic feet is federally owned and 1 billion cubic feet is privately owned. The United States does not have any significant leasehold rights in the depleting fuel gas resources. However, through the Department of the Interior, it does have leasehold rights to about 70 percent of the helium found in nondepleting natural gas, and it owns over 90 percent of the helium in storage.

Jan 1, 1979

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By Lee M. Manna

This report summarizes the program to design, fabricate, install and preliminary test a pneumatic braking system for 10-ton mine haulage cars. Major arrangement drawings are reproduced, pneumatic schematics, parts list and actual developed costs. Recommendations as to system improvements are made.

Jan 1, 1977

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

This report describes the work performed by Mine Research Company in developing a prototype mobile roof shield during 1971-1972 for the U. S. Bureau of Mines, along with background information leading to the design decisions adopted for the project. In addition, the report evaluates the choice of design and analysis and the results of the project in terms of future possibilities of mobile roof support systems. The report begins with the discussion of the problems of designing, building, and using mechanical and hydraulic roof support in coal mines. It then gives a historical summary of past work with discussions of the design choices made for previous roof support systems.

Jan 1, 1973

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Bradley V. Johnson

This publication summarizes the in-house and contract research and development projects conducted since 1974 by the Bureau of Mines for the control of noise and vibrations from surface mine blasting.

Jan 1, 1982

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By Joseph L. Buckley

A total of 55 conveyor belt fire tests were conducted in the Bureau of Mines Fire Test Gallery, located at the Factory Mutual (FM) Fire Test Center West Glocester, R.I. The objectives of these tests were to: 1) determine the fire resistance and burning characteristics of various conveyor belt materials under simulated mine conditions; 2) provide essential data for designing a reliable bench-scale conveyor belt fire resistance test; and, 3) determine fire test conditions that will discriminate between low, moderate and high fire resistant materials. Belts, representative of those which mold he found in underground coal mines were examined under n umber of experimental conditions which included; ignition intensity; air flow rate; ratio of belt bright (h2) to overall gallery height (h1); exposure time; and, belt width. It was found that fire propagation could be achieved for some "fire resistant" belts (complying with the present Schedule 2G standard for approval) when exposed to an Ignition source of =6000 Btu/min for a 15-min period at a belt height ratio of 01.66. There appears to be a dependency of flame propagation on air flow rates and belt width, although the tests performed do not provide a quantitative trend. Recommendations are made for additional work to resolve some anomalous date and to fill voids in the rest program.

Jan 1, 1978

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Elk Creek RARE II area during the summer of 1981. The study area encompasses 18,900 acres [29.5 sq mi (7,680 ha)] along Elk Creek, 18 mi (30 km) southeast of Covello, California. No mineral resources were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese and chromium. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By G. L. Fitzpatrick

Preliminary results of an experiment in seismic holography indicate that the techniques of acoustical holography may be successfully used with seismic waves to determine the size and general shape of underground objects. This experiment was carried out under field conditions on a moderately large scale compared with the typical laboratory experiments in acoustical holography. The object to be mapped was a 100-foot-diameter, spherical, low-velocity zone of explosively fractured rock in oil shale at an average depth of 80 feet. The seismic wavelength of the Fourier component wave used in making the seismic holograms was 50 feet at a frequency of 140 cps. The hologram sampling aperture was 226 feet square and was sampled by 441 geophones in a 21 by 21 rectangular array. One novel aspect of the experiment was the use of a wide-band polychromatic explosive source of seismic waves rather than a narrow-band quasi-monochromatic vibrator source. A successful laser reconstruction of the object image from a lensless Fourier-transform hologram in the form of a 5/l6-inch-square photographic transparency is illustrated. The size of the underground object measured from the laser reconstruction of the object and the size inferred from a knowledge of the amount of explosives used to fracture the site and the tensile strength of the oil shale are found to agree.

Jan 1, 1972

By Harold W. Lipper

BUREAU OF MINES helium plants produced a. record-breaking 477 million cubic feet of this essential element in 1959. The supply of helium was less than the demand before operations were resumed at the Navajo plant in July and begun Sit a. new plant at Keyes, Okla., in August. Helium was in abundant supply after August, and the informal allocation system which had been in use intermittently since 1955 was discontinued Delivery of 26 new tank cars in August and September increased the total in the tank-car pool to 163. Defense and space agencies and the Atomic Energy Commission continued to use more helium in their operations and research.

Jan 1, 1960

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By David D. Rabb

A report on location, sampling, assays, mineral examination, amenability leach tests, and evaluation of certain mine dumps in Mohave County, Arizona. Extractions of greater than 30 percent of the gold and silver were achieved during simulated heap leaching of selected mine dump material. Consumption of reagents was relatively low and results suggest leaching of prepared heaps is technically viable and could be economically attractive.

Jan 1, 1980

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962