Search Documents

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

By O. Dojcar

Equations for calculating the parameters of controlled blasting (burden and spacing of boreholes and weight of the bottom charge) are derived and analysed on the basis of empirical values and made more precise through incorporation of the properties of the rock being blasted and explosive applied. For the success of controlled blasting the correct choice of the blasthole diameter/charge diameter ratio is critical. This relation is defined as the coefficient of radial decoupling of the charge; it is recommended that it is chosen to be between 3 and 3.5. Analysis of smooth blasting, cushion blasting and presplitting indicates that cushion blasting is a less destructive alternative to smooth blasting, but it has a slightly higher blasthole consumption and limited possibilities of use. There are definite economic advantages to controlled blasting, especially in rock masses of low and medium strength

Dec 1, 1996

By I. R. Stevenson, J. G. Dunn, T. N. Smith, L. C. Mackey

An experimental flash reactor has been developed to simulate the operation of an industrial flash-smelter reaction shaft. Four concentrate materials of differing mineralogical compositions were characterised and then oxidised in the reaction shaft. The products were examined by chemical analysis to determine the extent of oxidation and by electron-probe microanalysis to determine the fate of individual particles. This programme of work enabled the influence of mineralogical composition and particle size on the extent of oxidation to be assessed

Jul 1, 1991

By M. Schwartz

Mining in Argentina is diverse in terms of the number of minerals extracted from the country, but also in terms of the varied approaches and attitudes of mining investors and their trust in the country's individual provinces. Laws are discussed, investment attractiveness and taxation.

Jun 1, 2015

By L Casari

A study of samples from three sectors of the mine, which was worked from Roman times to 1991, revealed different textures, mineral associations and distributions of trace elements in the sulphides. In the last decade before closure, grades of sphalerite concentrate were in the range 51.67-53.30% Zn and 2.21-2.86% Pb and of galena concentrate 69.43-71.62% Pb and 4.70-8.36% Zn, while the estimated by-product germanium content of sphalerite concentrates sold was 300-400 g/t. Passing the different run-of-mine materials through the same concentrator flowsheet produced middlings and tailings during the preconcentration processing. Separate and alternative treatment of run-of-mine products would have yielded improved recoveries of sphalerite and galena and better values of by-product germanium and cadmium

Jun 18, 1905

By NA NA

Listing safety award winners, £I43M has been added to proceeds from coal privatisation in the year to March 1997, bringing total revenues to over £1.3bn, some company news in brief.

Jan 8, 1997

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By T. Guyaguler

An analytical technique using computer-based multiple-regression methods was employed to determine the relation between the dust-producing index and inherent rock properties of typical samples from a coal-producing area, one of the aims being to provide a preliminary predictive tool for practical use. The investigation demonstrated that factors varied in their influence under different conditions, the brittleness:toughness ratio and the hardness being the most significant inherent properties with hardness showing the highest positive correlation coefficient

Jun 13, 1905

By D. G. Skinner, J. H. Griffiths, F. T. Williams, A. G. Withers

"The absence of homogeneity, in dust-clouds underground indicates the use of a method in which the volume of air sampled is an appreciable proportion of the total volume under consideration. Of the available methods, only the impinger and gravimetric techniques seem to comply with this requirement. In practice, greater efficiency of collection of the smaller particles is possible by the use of a gravimetric filter than with the impinger. For this reason if, as seems desirable, a standard method of sampling be sought, the adoption of a gravimetric technique is to be recommended.Provided that the amount of dust collected is reasonably large, the paper filter would seem to be preferable to the solid crystal type of filter on account of its greater convenience in use.Alternative methods of sampling are desirable to cover the wide range of practical conditions."

Jan 1, 1947

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

The mineralogical composition of the ore was determined and the mineral phases with which nickel is associated were identified. The ore was prepared by grinding to -420 micrometres and classification into granulometric fractions. Prior to the main series of experiments the effect of agitation rate on nickel recovery was investigated. The influence of sulphuric acid concentration, temperature and particle size on the kinetics of nickel extraction was then studied, both quantitatively and qualitatively, over fixed value intervals. Application of the initial rate method enabled determination both of the order of reaction with respect to sulphuric acid concentration and the activation energy for the dissolution of nickel. The results indicate that a physical mechanism can be ruled out as the rate-determining step in the extraction of nickel from the ore and that a chemical mechanism is more likely

Dec 1, 1991

By Evans E. C.

Discussion of the paper presented at the Manchester Geological and Mining Society' general meeting held in Manchester, March 14th , 1916, with Leonard R. Fletcher, President, in the Chair included contributions by Fletcher L.R., Paton J.D., Orchard A.J.A., Ross A., Gerrard J. and Stephenson H., with the author's responses

Dec 1, 1916

By Schwartz M.

Madagascar's democratic election has led to a return to its position as a preferred trade partner with the USA and a priority market with Canada. Michael Schwartz takes a look at two key mining projects in this recently reinvigorated country

Feb 1, 2015

By M. Schwartz

Hosting copper, gold, oil and liquefied natural gas, the country is an interesting target for miners. However, remote locations in inhospitable, unusual and difficult terrain cause problems. The government has worked to create a Sovereign Wealth Fund to manage government surpluses from minerals and energy but PNG scores very low among many criteria, including land dispute resolution, as revealed by the 2014 Canadian Fraser Institute in its survey of senior mining personnel.

May 1, 2015

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By R. Patel, J. Ephraim

The production of titanium dioxide (TiO2) from its minerals such as ilmenite is challenging, and subsequent isolation of titanium from TiO2 is even more difficult because of the metal-oxygen bond strength. Currently, titanium sponge is mainly produced via the Kroll process, which is energy intensive and generates large quantities of waste. A number of international research groups have come up with technologies for the production of titanium metal. However, none of them have been commercialised, because of engineering or economic issues. The team at Bradford have confirmed that ultra-pure titanium powders can be separated from TiO2 powder through metallothermic reduction and are working to scale up the process.

May 1, 2015

By S. G. Tsimas, A. K. Moutsatsou, S. G. Tsivilis, G. K. Parissakis

(NH4)2SO4 can be used with success as a leachant to remove gypsum contained in celestite ores. The process, which is applied before flotation, provides an upgraded feed and problems related to the simultaneous flotation of CaCO3 and SrSO4 are reduced. The process is independent of the gypsum content of the feed so that each leaching stage decreases the gypsum content by almost 50%. The use of (NH4)2SO4 has an insignificant effect on the co-leaching of SrSO4 (0.45 wt.%) at each stage

Jun 13, 1905

By A. Policard

The bodies of mammals possess a very efficient mechanism for ridding themselves of inhaled dust. When the lung is healthy this mechanism works very well, and dust is quickly and completely expelled from the lung either by the respiratory tract or the lymphatics. The mechanism, however, is easily upset, and slight alterations in the condition of the ciliated epithelium or the circulation of lymph are sufficient to interfere with it, therefore the second mechanism comes into play and the dust is fixed and immobilized in some part of the lung. This, however, is not a real cleansing process, since the lung becomes a dust-trap, and may become'pneumokoniotic. The mechanism is protective at first, but later, when the accumulation of dust is considerable, it gives rise to trouble. The lung cannot become, so to speak, a physiological dust-trap, and still retain its normal structure and function; pneumokoniosis begins, which is essentially a disease due to the mechanical presence of large amounts of inert foreign material.

Jan 1, 1947

By R. J. Gochin, P. Bevilacqua, G. D. Schena

This class of flowsheet-dependent simulators does not replace modular simulators, such as Modsim and Microsim, which are necessary for the assessment of different flowsheets before selection of the most desirable technical option and for investigation of the fine details of unit processes. The system presented here is regarded as complementary, serving in the early stages of feasibility studies as an aid to assessing the convenience and economics of preconcentration; the example used is of dense-medium preconcentration of a barytes-fluorite ore

Jun 13, 1905