Search Documents

By Don C. Warrington

This paper is a survey of the various methods and research efforts by which the drivability of piles is determined. First, a brief outline of the basic theory and the important parameters for driving by vibration are presented. Then, a wide variety of methods by which the drivability of piles is determined are presented and discussed, with special emphasis on methods developed in the USSR. Each of these methods are examined as to how they take into account the various parameters of vibratory pile driving, such as eccentric moment, frequency, dynamic force, motor torque and power, vibrating and static weight, and other variables. Some relation of these methods of field data is presented as well.

Jan 1, 1989

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By George G. Goble

In the middle of the nineteenth century, the dynamic formula appeared as a description of pile penetration during impact driving. The simplicity of use of the formula combined with the power of the energy concepts behind the formula caused it to be quickly accepted and integrated into practice. Dynamic formula had been in use for 100 years when the Wave Equation computer programs first appeared. With that long experience it is not surprising that the formula continued to be used and were only slowly abandoned. The Wave Equation offers many advantages over the various formula but it does not offer a clear sense of physical understanding of pile driving that is available with the formula. Large amounts of numbers are generated but often it is difficult or impossible to gain a physical understanding of the results or a feeling for the importance of the various parameters. The question that the Wave Equation user has is, "What will happen if I use a larger drive cap (or change any other item of equipment)?" In this paper, I will attempt to explain pile driving using elementary wave propagation theory. However, the presentation will not depend on any higher mathematics. With the use of wave mechanics, it is possible to explain driving characteristics that cannot be handled with the energy formula.

Jan 1, 1995

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

By Walter I. Paniagua

A housing complex of 76 buildings is being constructed in the city of Morelia, in western central Mexico; the buildings are 5 levels high, with a shallow concrete slab foundation. Soil conditions include a soft clay stratum, with up to 8 m depth, in a highly seismic area. Pile foundations and micro-piles were considered, but discarded due to economic factors. The alternative of soil improvement with rigid inclusions was used. An FEM (Finite Element Method) analysis was conducted to determine the diameter, spacing, length and arrangement of the inclusions. Construction was implemented with traditional methods: soil boring, and mortar tremied with pipe and the aid of a sock to contain the material (no steel reinforcement was used). So far, 46 buildings have been built, and level measurements for 18 buildings have been recorded since 2006, with resulting good behavior in both total and differential settlements.

Jan 1, 2008

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By Franklin M. Grynkewicz

As part of the Boston Harbor clean up project, the new 1,000 mgd Deer Island Sewerage treatment plant includes ten 240 feet high egg-shaped "residuals" tanks. Contract documents called for these structures to be supported on 2,600 sixteen inch concrete filled pipe piles. The project site is underlain by highly variable glacial and marine deposits. Subsurface conditions vary from one extreme where firm glacial deposits exist at subgrade to the other extreme where 70 feet of medium stiff clays overlying weathered bedrock must be dealt with. The most common profile consisted of 15-20 feet of sands, 20-40 feet of marine clays, and 20-60 feet of stratified glacial deposits (commonly called tills) overlying Argillitic bedrock. Post bid redesign work, initiated as a cooperative effort between the owner and the general contractor, demonstrated that an $8 million savings could be realized if high capacity 48 inch diameter caissons replaced the specified pipe piles. A highly unusual arrangement of having the general contractor and specialty subcontractor providing input to the owner&apos;s engineering team allowed the redesign work to proceed on a "fast-track" schedule.

Jan 1, 1992

By G. Noce

The ever more present necessity for greater precision in foundation structures on vertical piles subject to horizontal forces applied to the heads, in the light of of the latest knowledge about the elastic-plastic behaviour of the soil has led to the use of numerical calculation for the formulation of a general resolution method for the problem. The calculation method that will be set out, applicable to piles with inertia moments variable discreetly along their axes is especially useful when studying steel structures for medium and large tonnage vessels for which the metal piles are often constructed for the assembly of section of equal external diameter but different thickness and therefore different inertia moments. Two examples are given of constructions whose foundations have been projected with these calculation tools, one in the railway sector (foundation pile for the river Nera viaduct - Italy) important for the limitation of horizontal relative deck displacement, the other maritime (Dolphins of the petroleum pier of the port of Bandar Abbas - Iran).

Jan 1, 1989