Search Documents

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

By Zachary Q. Maassen

The purpose of this paper is to highlight the environmental benefits of properly managing slurry waste as it is generated on site. The following projects will be used to illustrate the importance of proper onsite waste management. Project: Jet Grout Backflow Dewatering The goal was to dewater the backflow directly onsite to produce a dry, solid waste and reusable water. The backflow spoil was pumped directly to the dewatering system as it was generated. Utilizing mechanical separation equipment and flocculation polymer the waste volume was reduced by 44%. Due to the site footprint and high volumes, slurry waste removal and onsite processing were the only two feasible options. Onsite dewatering proved to be the environmentally beneficial option as it eliminated the need for slurry waste hauling and disposal. The benefits of utilizing a dewatering system are listed below: Project: Soil Mixing Spoil Recycling for Slurry Wall Construction In this application the spoils generated contain bentonite mud, cement mixture and organic ground soils. The goal of this project was to process the backflow mixture to recover reusable bentonite mud and separate the soil as a dry, stackable waste product. The treatment system replaced the traditional method of vacuum truck extraction and facility disposal. The environmental benefits of properly handling the backflow is a decrease in fresh water usage, bentonite additive reduction, and the reduction of CO2 emissions. The paper will consist of a project scope, technical equipment and process description, environmental impact reduction calculations and lessons learned for each project.

Jan 1, 2018

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

By Rick Deschamps, Brian Barkauskas, Aled Hughes, Abigail Stein

In central Washington, six miles south of the small town of Vantage, the flow of the Columbia River is harnessed by the Wanapum Dam which is part of the Priest Rapids Hydroelectric Project owned and operated by Grant County Public Utility District (GCPUD). Extending more than 8,300-feet from bank to bank, the dam includes left and right earth embankments, left and right concrete gravity sections and a 10-unit powerhouse. Adjacent to the right embankment is a concrete gravity spillway featuring radial gates measuring 50-feet-wide and nearly 70-feet-high. In the early 1960’s when Wanapum Dam was built, these seven-story spillway gates were the highest in the world. In late February 2014, 50-years into its service life, during a routine maintenance inspection, observant workers noticed a slight misalignment in the roadway deck curbs and handrails located on top of the spillway. Further survey and inspection efforts uncovered a 65-foot-long by two- inch-wide crack that spanned the full length of Monolith 4. On discovering the extent of the damage, GCPUD initiated immediate drawdown of the reservoir to relieve pressure on the spillway monoliths. Wanapum Reservoir and the areas directly downstream of the dam were immediately closed, boat ramps and inlets were left completely dry, campsites were closed and boating activity was banned on the lake until further investigations and remedial procedures were in place and completed. An extensive root cause analysis ultimately led to the conclusion that errors in the initial design calculations and late changes to the final spillway design led to a condition that generated tensile stresses in the concrete at the upstream face, which over a period of 50-years resulted in the formation of a crack along a horizontal lift joint located about 85-feet below normal pool elevation. Further analysis showed that, although visible distress was found at Monolith 4, there was nothing preventing this issue from happening at other locations along the dam spillway. Although no visible cracking was found in the other monoliths, repair procedures for Monolith 4 would have to be replicated at the remaining monoliths.

Jan 1, 2018

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By Jogeshwar P. Singh, Ahmed AlaaEldin, Mohamed Ashour

The presented methodology allows the determination of the response of laterally loaded battered long piles in sandy soils based on the soil-pile interaction. The Strain Wedge (SW) model which was originally developed for laterally loaded vertical piles is modified to assess the behavior of laterally loaded battered piles with the consideration of soil and pile properties. The method predicts the pile-head response and associated p-y curves. The presented soil-pile model accounts for the variation of the direction and magnitude of the batter angles from the vertical position. Unlike current practice, the proposed technique also provides the p-y curves for battered piles in sandy soils based on soil and pile properties (i.e., sand relative density, friction angle, pile geometry, etc.). The proposed methodology has been validated through a number of comparisons with full/model-scale pile load tests. INTRODUCTION The influence of pile battering on the lateral response of piles is rarely studied in the literature. Over the last decades and as suggested by Kubo (1962) and Zhang et al. (1999), a p-y multiplier is applied to predict the response of laterally loaded battered piles from an equivalent vertical one. Several researchers conducted model-scale piles load tests to understand the behavior of battered piles subjected to lateral load (Juvekar and Pise 2008; Meyerhof and Ranjan 1973; Meyerhof and Yalcin 1994). However, such tests were conducted on model piles with diameters less than 30 mm which may not have reflected actual soil-pile interaction. Battered piles are generally categorized as positive or negative battered piles according to the angle of pile installation as shown in Fig. 1. From the small-scaled and numerical models of battered piles, it was found that the lateral capacity of negative battered piles is larger than that of vertical ones. On the other hand, the positive battered piles have lower lateral capacity when compared to vertical piles (Fan-ren and Ji-Ming 2011; Juvekar and Pise 2008; Manoppo 2010; Reese et al. 2004; and Reese and Van Impe 2011).

Jan 1, 2018

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006