Search Documents

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

By Mark A. Willian

The purpose of this short paper is to present soil profiles and basic soils information for the portion of the I-880 Replacement Project alignment where highway structures are to be built. The information presented here is derived primarily from foundation investigations conducted by the Caltrans Foundation Unit (currently the Structures Foundation Branch, Office of Structural Foundations) and by others under Caltrans direction. The foundation investigation for the I-880 Replacement Project began in May of 1991. The field work was completed in May of 1992 and consisted of 93 rotary sample borings, 11 consolidation sample borings, 6 TEXAM® pressure meter borings, six in-place vane shear borings and 57 electronic cone penetrometer soundings.

Jan 1, 1996

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By P. A. Neill, O&apos

The caisson foundation for Vent Building No. 6, at the southern landfall of Boston's Third Harbor Tunnel, was installed inside an unbraced concrete cofferdam 250 feet in diameter and about 70 feet deep. As a spectacular engineering feat, the cofferdam itself certainly ranks first. However, the foundation work within was no routine caisson job and made its own contribution to the state of the art. Comprised of 5 ft. diameter caissons socketed 10 to 16 feet in sound rock, it posed serious challenges in logistics, space limitations and time, requiring development of unique, purpose-made equipment. The unexpected discovery of significant depths of shattered rock overlying acceptable sound rock, along with other surprises of lesser import, compounded the problems. How these challenges were planned for, met and overcome is the subject of this paper.

Jan 1, 1994

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

[ENGLISH active earth pressure adapter additive adhesion admixture, addition adsorbed water aggregate air air entrainment air hose allowable bearing value allowable pile bearing load]

Jan 1, 1994

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By F. Schlosser

The extension of Montparnasse Station in Paris required the construction of supports of very high unit capacity to support a particularly rigid super-structure. The majority of the site is characterized by the existence of old limestone quarries at a depth of approximately 20 metres. These workings have been backfilled in some places, have collapsed in some places and have given rise to local subsidences in the marne layers above them. This paper addresses the steps taken by the group of companies and their consultants to evaluate the equivalent stiffnesses of the supports necessary for the design of the superstructure, and gives details of the construction techniques chosen by the foundations specialist to adapt to the particular conditions encountered on this site.

Jan 1, 1989

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018