Search Documents

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Morgan NeSmith

The Port of Palm Beach is a full-service landlord port in Riviera Beach, Florida. The port and its tenants process more than $14 billion in commodities. About 80% of these are exports, which makes the Port of Palm Beach one of only 16 "Export Ports" in the U.S. More than 2.5 million tons of cargo move through the port every year. Ozinga, a fourth-generation family- owned construction materials company, has supplied ready-mix concrete for commercial, residential, public works, landscaping and excavation projects from several of its Florida locations. It planned to build a one-of-a-kind cement storage facility to receive and store international ship- ments of cement for transport to other facilities for the production of ready- mix concrete. Dome Technology, of Idaho Falls, Idaho, designed and constructed the 125 ft (38 m) diameter storage facility. The design and working volume of cement for the facility was just under 27,000 cu ft (765 m3). The design loads required to be supported by the foundation system are shown in this table:

Apr 1, 2023

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022

By Matt Sotirin

The Santa Fe train station and passenger rail platform were constructed in the downtown district of Fort Madison, Iowa, over a century ago. This landmark building and rail platform were in need of major renovations and rehabilitation in order to restore the site to a functioning railway train station. A multitude of key players from various public and private parties were involved in the design and construction of this project site. Part of the project consisted of constructing the passenger platform. The original design included helical piles to provide foundational support for the platform. Challenges occurred during construction due to the presence of an obstruction in the form of a poured concrete slab in the immediate area where the helical piles were to be installed. The contractor worked with the engineer of record and other consulting parties to value engineer the helical pile design and utilize self- drilling micropiles as a replacement to the specified helical pile system.

Oct 1, 2022

By K. J. Yang

Based on investigations and model tests combined with pile foundation on Code compilation of drydocks, we present this report to give informations against uplift pressure of piles beneath floor of drydock. In a same kind of soil, we have got comparative tests results with single pile and pile group, and the latter was performed at different spacings, different embedded depths and different number of piles in the group. Having analyzed through the results, there are some new understandings of regularity about failure mechanism and uplifting capacity of single pile and pile group, as well as optimum embedded depth of pile foundation. The results of research approach to measured values of full-scale and model tests at home and abroad, it has been placed into the Design Code of Drydock in China (1985), and can give a reference to design of pile foundation at sea and on land under uplift loading.

Jan 1, 2010

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1998

By Anne Fagot

Because of the risk of corrosion caused by stray currents, steel foundations and steel sheet piling are generally prohibited in the vicinity of railway structures. Steel solutions are only accepted if they are shown to meet the required design working life and if this can be achieved at an acceptable cost compared to competing materials. The influence of stray currents on various steel sheet piling designs was studied using software initially dedicated to gas and pipeline industries and cathodic protection systems. It has been successfully adapted to model stray currents affecting steel sheet piling. Corrosion rates assessed using this modeling software were considerably lower than commonly expected. Zones of potential corrosion risk were identified; specific cost-effective countermeasures could be established. The developed software tool can help to optimize the design of piling solutions in the vicinity of DC railway power systems in terms of suitable countermeasures that meet structural reliability and cost requirements.

Jan 1, 2008

By Anne Lemnitzer

When a major storm system stalled over Western Europe last summer, it pro- duced the deadliest flood on European territory in the last two decades. Beyond record-setting rainfall over countries such as Luxembourg, Switzerland, France and the Netherlands from the storm's "Bernd" low pressure system, more than 230 people were killed in Germany and Belgium. The storm system also caused over an estimated $20 billion (€17.7 billion) of damage. A team from the Geotechnical Extreme Events Reconnaissance (GEER) Association, supported by the National Science Foundation, was mobilized to investigate the potential impacts of the widespread flooding in Germany, Belgium and the Netherlands. Members of the DFI Europe regional chapter closely collaborated with the U.S.-based GEER team and many other engineers and scientists in Europe to collect perishable data and study flooding effects and the event's resulting impacts on geostructures, such as bridges, retaining walls, dikes and embankments. This article features some of the vast information collected by the team, which has recently been published in a comprehensive reconnaissance report and made available for free at geerassociation.org. All data will also be accessible at the NEHRI DesignSafe Cl data repository.

Feb 1, 2022

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By B. Philip Shull, Allen W. Cadden, Johanna M. Simon, Michael S. Senior

A 670 linear meter (2,200 linear foot) large-diameter sanitary sewer interceptor installation at depths ranging from 3 to 10 m (10 to 30 ft) below existing grade in an area with a high water table requires careful attention to design and performance of the system during construction. Highly variable soil and rock conditions at the site necessitated the design and construction of various excavation support systems along the alignment. In addition to the subsurface condition challenges faced at this site, the proposed sewer pipe was to be installed between an existing active combined sewer main and a high pressure gas main feeding the nearby city. What better way is there to monitor performance of the system than to require a detailed instrumentation system? Instrumentation system specifications and designs are becoming more commonplace in the industry, but it is always important to sit back and take a look at the whole picture. What are you looking to gain from your monitoring? What pieces of information are useful? What interpretations can you derive from the instrumentation you have selected? This paper will address the instrumentation system used to monitor the 670 m (2,200 ft) excavation from the specification requirements to the implementation and interpretation. This case history will delve into the challenges faced and methods used to overcome those challenges on this particular support of excavation (SOE) project. A combination of soldier pile, lagging and sheeting, and shoring systems was used to achieve the necessary excavation support. In designing the systems, attention was given to the configuration of the bracing system to allow the sections of largediameter pipe to feasibly be installed in the excavation while maintaining the SOE system.

By John Y. L Chen

This paper presents full-scale instrumented pile static compressive and tensile load tests to be conducted in the area of Pearl Harbor, Hawaii. Thousands of piles have been installed to support the existing piers and wharves in the Pearl Harbor area. Due to the absence of bedrock within practical depths, most of the piles use combined friction and end bearing. A new 925 feet (282 meters) long and 50 feet (12 meters) wide reinforced concrete wharf supported on pile foundation is planned. This paper will present results of soil investigation, laboratory testing, dynamic load tests during indictor pile driving and static pile load tests. The subsurface conditions consist of soft harbor sediment, young alluvium deposit, volcanic tuff rock formation and stiff old alluvium deposit. The load test piles consist of 20-inch (508 mm) square and 24-inch (610 mm) octagonal pre-stressed, pre-cast concrete pile and instrumented with embedded strain gauges. The length of the piles ranges from about 50 to 125 feet (15 to 38 meters). The test pile program consists of probing, driving indictor piles, dynamic load tests during indictor pile driving and static load tests. The standard loading procedure method was used during static pile load tests.

Jan 1, 2002

By Ray Zelinski

Caltrans sponsored a research project in 1992 which incorporated proprietary and generic pile types. The piles were subjected to axial tensile/compressive loads in deep, soft soils. Descriptions of various pile types and systems, scenarios leading to the proposal to test the systems, and load test results were/will be provided by other presenters at this seminar. Therefore, this paper will focus on the issues surrounding use of test results and proprietary pile systems on Caltrans construction projects. The primary issues facing Caltrans during implementation are as follows: 1) producing pile cap designs for a range of pile types and loads; 2) providing construction specifications which allow fair competition among the system vendors, yet assure design and ultimate capacities; 3) Develop quality control standards for pile system materials and installation techniques which guarantee pile durability for static and dynamic loads; and 4) assure that foundations have adequate lateral capacity.

Jan 1, 1993

By Andrew Stauble

This project included the replacement of the Long Island Railroad (LIRR) Atlantic 6 Bridge in New York City, which services rail traffic and spans the Van Wyck Expressway and frontage roads. The bridge re- placement was part of an overall project to widen the Van Wyck Expressway between Kew Gardens and John F. Kennedy Airport, which serves as the major route for vehicular traffic between the airport and the city. The railroad bridge crosses the expressway and frontage roads in a significantly congested area, and it services an average of approximately 140,000 commuters per day through- out the boroughs of Manhattan, Brooklyn and Queens. The existing bridge superstructure and foundations were to be demolished and new structures and foundations were proposed to be constructed at the bridge's east and west abutments and center pier. The new bridge would be supported on driven H-piles. To facilitate the construction of the new bridge's abutments and center pier, a support of excavation design was required to support the grade around the existing structures. The design shown on the contract drawings included a driven soldier pile and lagging wall with multiple rows of drilled tiebacks at the abutments to laterally support excavation heights of up to 36 ft (11 m). The existing abutments are located directly adja- cent to frontage roads that have an extremely high vehicle traffic volume,

Aug 1, 2023

By Michel Bustamante

The original Cistercian Lure abbey situated in eastern France and built in the second half of the 16th century, has become nowadays an administrative building. Because it has been founded on poor ground conditions and inadequate foundation scheme, the abbey has suffered severe structural distortion. In 1992 an inspection revealed new extensive damages which led to a general refection together with a foundation underpinning. Micropiling was the selected method. Movements recorded over a period of 6 years after underpinning completion are presented.

Jan 1, 2002

By Thomas Kennedy, Michael Bennett

"History never repeats itself, but it often rhymes." The old aphorism reflects how the study of the past may, perhaps, be most widely valued when it can be used to improve current and future decision making. The education the authors received as geotechnical graduate students certainly impressed upon them the importance of recognizing that not all wisdom is necessarily new. Much of their graduate coursework involved reading technical papers that had introduced concepts of outstanding historical significance in the field, such as pore pressure coefficients, stress paths, and the stress history and nor- malized soil engineering model. These papers gave the authors both respect for and interest in the historical develop- ment of the field. After graduation, the authors furthered and deepened this interest by continuing to expand their knowledge of the profession through both experience in practice and the review of additional literature.

Jan 1, 2023

By Rodrigue Karam

An assessment of the geotechnical conditions at the Manhattan Cruise Terminals (Piers 88, 90, 92 & 94) was conducted after excessive settlement and structural distress was reported at Pier 92. The piers are located on the Hudson River along the west side of Manhattan, New York. The following paper focuses on the investigation and analysis performed on Pier 88 located at the western terminus of 48th Street. The pier is supported by approximately 2,500 timber piles bearing on soft organic silts and clays. The first portion of the analysis consisted of an offshore field investigation and laboratory testing to classify the subsurface soils within the project area and estimate the geotechnical capacities of the timber piles. Additionally, a settlement analysis including consolidation and negative skin friction analyses was performed to evaluate existing settlement levels. Axial and lateral analyses were performed to develop the soil springs (p-y, t-z, and q-z curves) necessary for the structural analysis.

By M. Nomura

This paper describes the results and field measurements of two long-term observation tests and two short-term loading tests to confirm the effectiveness of NF piles in reducing negative skin friction. All the test piles were equipped with strain gauges, allowing measurement of the compressive axial forces in the piles. These test results prove that NF piles are effective in reducing the negative skin friction to an insignificant value. Some examples of the design procedures used in Hong Kong and Japan are also presented.

Jan 1, 2010

Caissons hand dug to a depth of about 100 feet were used to underpin three important structures at an industrial site in the State of Utah. The caisson shafts extended through 30 to 40 feet of coarse, granular soils and 25 to 60 feet of sands and clays to bear on a very dense, coarse gravel and cobble stratum near the water table. The shafts were belled to 12 feet square at their bearing elevation. Bearing pressures of 20 ksf were assigned. The shafts were lagged with timber. The use of hand-dug caissons allowed continuous operation of the facility during underpinning. Settlements after underpinning have been minor and well within the estimated magnitudes. Instrumentation was placed in two of the caissons with varying degrees of success.

Jan 1, 2010

By D. E. Sherwood

Twelve toe grouted, and eleven ungrouted piles, founded in very dense sands have been analysed to establish how toe grouting enhances pile performance. It is shown that pile stiffness is greatly increased, and that pile bases work effectively. This is in contrast to ungrouted piles, where some milli­meters of base movement may be required before the base is mobilised. Grouting appears to recover most of the disturbance caused during construc­tion, but in general does not enhance the ultimate bearing capacity of undisturbed ground.

Jan 1, 1989

By H. R. Shen

Cushion materials are one of the most important links in an efficient piling system. In the past, little has been done in China on this problem, so engineers are still used to those traditional woods, papers and coir ropes. In this paper, the SOA of piling cushions, their testing method and parameters used in wave equation analysis for piling are briefly reviewed. The static and dynamic mechanical characteristics of 3 types of cushion material have been determined in laboratory and suggestions about testing method and evaluation of test results are given.

Jan 1, 2010