Search Documents

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By Patrick R. Taylor, T. A. R. Putra

A review of various methods to treat high arsenic copper concentrates through pyrometallurgical processing is presented. Examples are drawn from various past and current operations and research. Various aspects of the engineering alternatives for treatment methods are discussed. Some of the methods discussed include: controlled oxidation roasting, adaptation of some smelter technology to accept higher amounts of arsenic, complete oxidation with arsenic fixation; sulfation roasting; acid baking, soda ash roasting, and others methods. Other topics include: a short discussion of other problematic impurities; the effects of arsenic on copper electro-refining and product purity; and methods for the ultimate disposal, or marketing, of the arsenic. The latest work being done at the Colorado School of Mines on soda ash roasting is also presented.

Jan 1, 2014

By Melanie Grob

Two commonly estimated fractal dimensions, called b and D values, represent statistical characteristics in the distribution of magnitude sizes (b) and spatial hypocenter locations (D) of microseismic events, respectively. We postulate that the values of b and D are related to specific stress regimes. Through different case studies of fluid injection into an oil/gas reservoir or geothermal field, we infer that the measured temporal variation in fractal dimension b is most likely due to significant changes in the local stress regime. The fracture dimension D indicates the spatial clustering of events. The distribution of these events can vary with time because of stress perturbations that (re)activate fractures whose direction favours their movement under a specific stress regime. Thus a combined statistical study of these two dimensions can help infer the variations of local stresses in a reservoir.

Jun 1, 2012

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By X. Cao, X. -G. Chen, K. Liu

Due to the detrimental effect of platelet iron-rich intermetallics on mechanical properties (particularly ductility) in cast alloys, it has been essential to transform these phases into Chinese script morphology. In the present work, the effects of Mn and/or Si addition and cooling rate on the phase transformation of the iron-rich intermetallics in 206 cast alloys with different Fe contents ranging from 0.15 % to 0.5 % were systematically investigated. The results obtained showed that platelet ß-Fe and Al3(FeMn), Chinese script a-Fe, Alm(FeMn) and Al6(FeMn) can be observed in the 206 cast alloys, depending on the Fe, Mn and Si contents as well as the cooling rate. It was found that the addition of either Mn or Si favors the formation of Chinese script iron-rich intermetallics but inhibits the precipitation of the platelet phases. In addition, the combined addition of both Mn and Si has a synergistic effect on the phase transformation. Furthermore, there exists a critical cooling rate to effectively suppress the formation of platelet iron-rich intermetallics for a given alloy. The threshold cooling rate decreases with increasing Fe, Mn and Si contents. Casting process maps are established to correlate the intermetallics precipitated with alloy chemistry and cooling rate for 206 cast alloys containing various Fe levels.

Jan 1, 2014

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007

By W. A. Bell

The Carboniferous system of rocks in the Maritime Provinces include as workable mineral and organic substances, gypsum, anhydrite, salt, coal, building stones, grindstones, limestones, brick-clay shales, fire-clay shales, oil shales, etc. The system is, therefore, pre-eminently of economic value to the provinces in which it occurs, and the more knowledge we may gain concerning it, the more we may be prepared to aid in the development of these useful substances. For this purpose it is not sufficient to state that the ground upon which we stand is underlain by Carboniferous rocks. In-discriminate digging or drilling will not open many new mines of wealth, however difficult it may be to dampen the optimism of gamblers. For mineral wealth has not been scattered in the rocks haphazard, now here, now there, but its distribution has been the result of natural earth forces acting at intervals throughout the countless millions of years that have elapsed since our planet was born. As regards the majority of metalliferous deposits, the earth forces involved have resulted in the penetration of surface or sub-surface rocks by molten rock-matter and associated mineral solutions from deep-seated sources. But the economic Carboniferous deposits that have been mentioned are themselves types of bedded surface rocks rather than immigrant deposits, and their formation and geological history is closely related to that of the rocks with which they are interbedded.

Jan 1, 1924

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By A. Lemay, G. Morin, C. Desmeules

"Incorporated in 1976, Sidbec Normines was mandated to exploit a deposit of specular hematite at Fire Lake. A combined effort of three companies, Sidbec, which holds 50. 1 % of the actions, British Steel Corporation another 41.67 % and finally Quebec Cartier Mining, a subsiduary of U.S. Steel Corporation, with still another 8.23 %.The deposit is located 60 miles north of the town of Gagnon. The extracted ore is crushed, in a giratory crusher, to-8 11 chunks, and from there, it is transported, by rail, to a concentrator at Lac Jeannine.A concentrate containing 65.5 % Fe and 5.5 % Sio2 is produced, using conventional methods like autogeneous mil ls and spirals. The concentrate is then transported by rail to the Port Cartier installations.The installations in Port Cartier include a secondary concentrator, a pellet plant, and stockpiling facilities for pellets and concentrate. The pellet plant has two product lines in paralel, producing a total designed tonnage of 6 millions tons of iron ore pellets, of which 3mi11ions tons are used in direct reduction furnaces.The secondary concentrator is designed to remove a portion of the silica contained in the ore, usually less than 2 % Si02 should remain from the original 5.5 % Si02 in order to produce iron ore pellets which are well suited for use in direct reduction and electric furnaces."

Jan 1, 1981

By André Bérubé

Since the disappearance of Les Forges du Saint-Maurice at the end of the last century, many historians have taken an interest in the lengthy past of this enterprise. They considered the political, socio-economic, administrative and anecdotal aspects of the industry, but barely dealt with the elements of technology. The purpose of this article is to try to fill this gap (1). Les Forges du Saint-Maurice was an integrated industrial concern, specializing in the production of semi-finished wrought iron and finished cast iron that operated almost without interruption between 1734 and 1883. Les Forges first came into being in 1729, when Montreal merchant Franc;ois Poulin de Francheville submitted to the King of France a request for the right to exploit the bog iron ore deposits on his seigneury of Saint-Maurice. This request, agreed to in 1730, was one of a long series of attempts, previously unsuccessful, to establish a local iron industry in the colony. Several such proposals were held up by a lack of capital from promoters or a too rigid application of the mercantilist policy by the metropolis. In 1730, however, the French minister Maurepas favoured a more liberal policy which would encourage private enterprise. The benefits of an iron industry to the naval construction industry was a factor that caught the attention of administrators. The choice of the site for Les Forges was based on the following factors: - the abundance of surface deposits of bog iron ore in the Saint-Maurice region; - the presence of a vast supply of hardwood and conifers needed in large quantities by this industry; - the proximity of sandstone and limestone deposits, md1spensable materials for the construction and operation of the blast furnace; - the presence of a water stream, with sufficient flow to provide the hydraulic power needed for the operation of the machinery.

Jan 1, 1999

"Virtual reality, a 3D computer-generated environment, has become a recognized delivery system for many forms of education. This paper describes the application of virtual reality to mineral processing education. An interactive mineral processing visualization module developed at the University of New South Wales, Australia, provides users with an overview of a base-metal concentrator and details about how the mined ore progresses through stages in processing. The module also involves developing instructional based plant layouts and flowsheets in the virtual environment. These assist the user in understanding the essential components of the base-metal concentrator.RÉSUMÉ La réalité virtuelle (RV), un environnement en 3D généré par ordinateur, est devenue un système de prestation reconnu pour diverses formes d’éducation. Cet article décrit l’application de la réalité virtuelle à l’éducation dans le domaine de la minéralurgie. Un module interactif de visualisation du traitement des minerais développé par l’université de Nouvelle-Galles du Sud, en Australie, offre aux utilisateurs une vision d’ensemble d’un concentrateur de métaux communs ainsi que des détails concernant la progression du minerai extrait à travers les différentes étapes de traitement. Ce module implique également le développement de schémas de réalisation et de traitement didactiques dans l’environnement virtuel, lesquels schémas aident les utilisateurs à appréhender les composantes essentielles d’un concentrateur de métaux communsINTRODUCTIONVirtual reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through technologies such as 3D graphics, audio feedback, and special peripheral devices to produce interactive environments.Virtual reality has been used in diverse fields including medicine (Riener & Harder, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 1992; Schofield, Lester, & Wilson, 2005). Virtual reality is also becoming the recognized delivery system for education in many fields, including engineering (Bell & Fogler, 1996, 1998; Shin, 2002). For example, VR laboratories have been designed and developed to teach users fundamental features of heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron-making process (Babich & Senk, 2009), and to guide users to identify various safety measures while working in a real laboratory (Bell & Fogler, 1996)."

Jan 1, 2017

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By E. Benguerel, G. Monteith, L. Centomo, S. Pelletier

In early 2007, it became apparent that with changing concentrate feeds, the magnesium (Mg) load projected for CEZinc starting in 2009 and beyond would quadruple and overwhelm the current Mg process bleed capacity. A project was started, following design for six sigma (DFSS) standards, to select both the optimal process and to evaluate its target capacity for the Mg bleed circuit. The economic and process risks of under or over-designing while Mg reduction efforts were underway at the mines also needed to be evaluated. This paper describes the project methodology, the impact on the plant, and some potential optimizations for CEZinc's basic zinc sulphate (BZS) Mg bleed process.

Jan 1, 2008

The article presents an outline of methods and certain results of laboratory tests, underground tests and model tests, aimed at assessing performance of a powered shield support on the floor of low strength parameters. The tests were conducted within the framework of GEOSOFT project co financed by Research Fund for Coal and Steel (RFCR-CT-2010-00001). The described research works were conducted by Central Mining Institute (Glówny Instytut Górnictwa), Janina coal mine and Becker-Warkop

Aug 1, 2013

By Marcel Vallée

Abstract -Traditionally, samples collected for mineral deposit evaluation have been viewed without explicit reference to reliability, with the illusion that a true value is attainable from a few samples and verifications. For exploration, mineral deposit estimation and production quality control the following definition is proposed: "a sample is a small quantity of material relative to the geological mass it represents, collected according to a systematic procedure, of measurable reliability, from which the grade/quality of the mass which it represents may be estimated, based upon appropriate protocols. This paper will concentrate on the actual rock sampling process. Too often, sample size has been, and is still viewed as a matter of convenience, leaving out representivity considerations, despite the importance of samples on project estimation. Linear samples (chips, channels, drill), panel samples, broken rock or mining samples and very large samples are considered. Collection procedures and quality control protocols to improve the representivity of non-mechanical samples are proposed.

Jan 1, 1998

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By P. Latostenmaa, T. Veneranta, J. Järvi, E. J. Peuraniemi

Boliden Harjavalta has operated a copper flash smelter since 1949 thus the smelter celebrates 70th anniversary of flash smelting in 2019. This paper shortly describes the historical perspective of the smelter and gives an update of the current operational issues and process modifications made during the recent years. The plant has carried out several major investments lately providing a firm view on the future. A new landfill area for the final slag was commissioned in 2018. A modernization of the concentrate storage area, a new acid plant and a debottlenecking project of the smelting line have been recently commissioned. At the same time, the tankhouse capacity will be expanded. This paper focuses on smelter modernizations. INTRODUCTION Boliden is a metal company operating mainly in northern Europe with core competencies in the fields of exploration, mining, smelting and metal recycling. Boliden Harjavalta, located in Finland, is part of the Smelters Business area of the Boliden Group and operates a copper and nickel smelter with related sulphuric acid plant in Harjavalta, and a copper refinery in Pori. As a short historical review, Harjavalta’s history may be dated back to the year 1910 when the Outokumpu ore body in eastern Finland was discovered. By the end of 1913, a copper mine was in operation and a copper plant based on Hybinette process was ready for commissioning. Due to difficulties in metal recoveries and throughput the Hybinette process was permanently shut down in 1929, and 100% of the mining production was sold as concentrate abroad. As the mine production increased steadily, a decision of a new smelter was made in early 30’s. In 1936 Outokumpu’s copper smelter based on electric smelting was commissioned in Imatra. The smelter was dismantled and transferred to Harjavalta during the final stages of the Second World War. The copper refinery started in Pori already in 1941 and the first copper anodes were cast in Harjavalta in 1945. First sulphuric acid plant started operation in 1947. Due to the post-war shortage of electrical energy, the plant metallurgists initiated a major development work to start exploiting the latent heat of concentrates. Thus, the flash smelting method was developed in Harjavalta and commissioned in 1949. Ten years later, flash smelting was also applied for nickel concentrates. Table 1 summarizes major historical and technical milestones of Harjavalta. The history of flash smelting is described in details in another paper of this conference (Jåfs et al., 2019).

Jan 1, 2019