Search Documents

By Z. Pilecki

This work concerns the identification of weak zones in the structure of a rock mass endangered by outburst of gases and rocks in the Rudna copper ore mine at greater depths (approximately 1200 m). A special methodology has been undertaken for the recognition of that threat in the wake of an outburst in the mine in 2009. No similar phenomena have been previously recorded in KGHM Polska Miedz copper ore mines. The research described in this paper was carried out in the new part of the deposit prepared for mining. Geophysical methods were used: seismic tomography and borehole ground penetrating radar (BGPR), along with particular identifications using geological engineering methods. In the researched area, Permian layers of sandstone and shale clay (Weissliegendes formation) and of Zechstein dolomite (top of Rotliegend formation) and anhydrite occur in the copper ore deposit. The rock layers are characterized by variable thickness and intensity of mineralization, varying internal structure, and local fracturing containing different gases and water. It is assumed that accumulation of gases occurs in the tectonically fractured dolomite. The study was focused on the recognition of the structure and properties of the dolomite layer lying directly within the roof of excavations. The first tests were performed with seismic tomography for the recognition of anomalous changes in the elastic properties of the rock mass. The results of these studies were used to design a control borehole for a detailed geological engineering assessment and BGPR surveys with 100MHz antennas. Seismic tomography enabled the identification of changes in Pwave and S-wave velocity, the Vp/Vs ratio, dynamic Poisson's ratio and dynamic Young's modulus. It was clear that seismic anomalies required verification by other methods. The BGPR survey was performed in a specially designed borehole, passing through the selected seismic anomalies. While the borehole was being drilled, the outflow of gases was identified, with varying amounts of CH4, CO2, and H2S detected, as well as water outflow. The results of BGPR confirmed the location of a reservoir of water and gases, about 30 m in length, found in layer of dolomite. The direct cause of the BGPR anomaly was assumed to be intensive fracturing, a greater content of clay material in the dolomite, and the presence of water in the fractured zone. The BGPR image was correlated with information on lithology, fracturing based on the RQD index and additional information acquired during drilling about water and gases surveys and other symptoms. The achieved results also showed a very strong correlation between the location of the zone containing gases and water and the anomalous S-wave velocity and field of dynamic Poisson?s ratio, and to a lesser extent other seismic parameters. It was found that the other measured seismic anomalies may be of the same nature as those identified in the control borehole and accordingly will require the implementation of detailed identification. The performed tests have also shown the usefulness of geophysical methods to identify geodynamic hazards under the geological and mining conditions of the copper ore deposit in the Rudna mine.

Aug 1, 2013

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By J. Arzúa, L. R. Alejano, P. Rodríguez

"After six years of successful excavation with a support pattern, some roof failures have happened in a room-and-pillar underground mine excavated in a stratified rock mass. In this paper the authors give explanation to the failure mechanisms and redesign the support in order to solve the recent problems of roof collapse.The mine magnesite bed is approximately 14 m thick, and runs in the E-W direction with an average dip of 18º. Due to mine constraints and the inexpensiveness of the ore, the excavation is performed in the mineral itself, avoiding the need for mining dumps and waste excavation. Rooms and drifts are oriented in the mineral bed to form an angle of 19º to the direction of the strata, reducing the roadway gradients to less than 10%. Rooms are 11 m wide and pillars are 7 m wide. They are designed to leave a 1 meter thick magnesite bed in the roof of the rooms to act as a supporting beam. More often than not there is a layer of very poor quality marly shale up to 1 m thick resting on this magnesite beam. Overlying the poor quality marly shale there is a better quality, self-supporting sandy shale.First, a characterization of the involved rock masses (magnesite, marly shale and sandy shale) is performed, collecting the geotechnical data from previous studies and performing new in situ geotechnical surveys to check the soundness of the previous data. A distinction is made between different quality zones inside the mine by means of the RMR classification, associated to the occurrence of faults.Back-analysis of some of the failed rooms and data from exploration boreholes were used to determine the failure mechanisms (associated to Voussoir type failure or occurrence of sub-horizontal joints crossing the magnesite beam). Based on an understanding of these mechanisms, the method used to design the support and to analyse the stability of the different possible thicknesses of the magnesite beams of the rooms and drifts of the mine were improved.Numerical models of the most relevant conditions found in the mine were performed in order to better understand the behaviour of the roofs and to simulate the supporting solution obtained in the previous analyses.The most relevant conclusions with regard to the main elements causing the instability of the roof include the appearance of sub-horizontal discontinuities crossing the magnesite bed, which causes total instability of the roof and usually leads to collapse; excessive thinness of the magnesite beam in the problematic rooms; and the relaxation of the deepest (around 270 m in depth) zone of the mine because of existing faults."

Jan 1, 2015

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By J. Dubinski

This paper describes the key circumstances of the underground coal gasification (UCG) process, which is planned to be carried out in the Polish hard coal mine ?Wieczorek?. The construction and field tests of a UCG pilot plant have key issues that need to be addressed to realize the research project goal: the elaboration of a highly effective technology of fuel and electricity production. The project will conduct several monthly tests of gasification in the pilot geo-reactor, which will be constructed based on the results of laboratory tests. The realization of the process requires numerous appropriately prepared actions adjusted to natural conditions in the hard coal deposit. Based on scientific principles, it is necessary to elaborate the procedures related to the location of the UCG installation (including its legal and safety aspects), and to perform a technical risk analysis. In addition, it is necessary to determine the required mining, geological, technical, economic and organizational circumstances, while at the same time considering the real but constantly changing process conditions.

Aug 1, 2013

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By Joël P. T. Kapusta, Liam J. Watt

The last extended copper smelting and converting survey dates back to the 2003 International Copper Conference held in Santiago, Chile. The following year, the Minerals, Metals, and Materials Society of AIME (TMS) started a new series in its Journal of Metals (JOM) called JOM World Nonferrous Smelters Survey devoting its first Part to Copper. The copper smelting landscape has significantly changed in the past 15 years, both in geographical terms with the shift of copper smelting production from the Americas to China and in technological terms with the growing adoption rate of Top-Submerged Lancing (TSL) technologies and the development and implementation of Bottom-Blowing technologies. A copper smelting survey update, even if not as in-depth as the 2003 Copper Smelting Survey, is therefore in order. The authors will review the latest trends in copper smelting technologies and production worldwide in comparison to the landscape of the early 2000s. INTRODUCTION This 2019 copper smelting survey is different from previous surveys as our data does not originate exclusively from responses to a questionnaire sent to all the copper smelters. Our data comes from several sources. We are therefore very thankful to the International Copper Study Group (ICSG) and Wood Mackenzie for sharing some of their information and to ENFI, Outotec, and Glencore Technologies for helping us cross-check our numbers for the Chinese smelters, flash smelting, Ausmelt, and Isasmelt technologies. Our survey presents data reporting from a total of 96 operating copper smelters from around the globe, which is significantly higher than the 50 surveyed in 2003. Although secondary smelting numbers have steadily increased over time, this paper focuses on primary smelting operations with copper concentrate as feed material. The list in this survey is still far from complete, with missing information from several known smelting operations. The total primary copper production tonnage of the smelters we surveyed amounts to 18.3 million metric tonnes from 29 countries representing 92% and 94% of total world primary production for 2018 estimated by ICSG and Wood Mackenzie, respectively. This representation has increased from 2003 when the total was 9.71 million metric tonnes from 23 countries accounting for 73% of world production. The trends presented and analyzed within this paper have stronger significance because of the increase in production accounted for. The Chinese and Russian smelter information collected is more detailed than years past. Our complete dataset is summarized in Table 1 at the end of our paper.

Jan 1, 2019

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By J. Walenzyk

This report investigates the limited use of super large backhoes in surface mines around the world. The demand for super large (> 700 t) hydraulic excavators is rising and most of the machines are sold as front shovel (FS) application. Despite advantages in faster cycle times super large backhoe (BH) machines are a minority (ca. 1% of the total machine population). This investigation is based upon the comparison between the volumes available to the BH and FS in one block and before the machine needs to move. The working conditions are created with standard parameters as given by Original Equipment Manufacturers of hydraulic excavators regarding bench height, angle, and material density. The travel amount of both machine types is derived from these volumes and compared. Furthermore, the travel amount of super large BHs is compared to the travel amount of smaller mining BHs and evaluated based on attachment length and bucket size. The calculations conclude that the volume of material recoverable in a single spot is about 75% higher for FSs. This leads to an increased travel for BHs. The combination of both the increased appearance of electrical driven machines (in the class of > 700 t excavators) and the travel amount lead to a high risk of damaging the cable or the excavator. Enlarged wear on the travelling parts is also attended by the higher travelling. A direct comparison of commonly found working set ups shows that the ratio between volumes is 32% which leads to an increased travel amount. In comparison with a 250 t BH, the calculation shows that the smaller BH is able to reach nearly 50% of the volume of the super large BHs. The main reason for this is the respectively high reach on smaller machines which, combined with other factors, leads to a significantly higher number of BHs in lighter classes.

Aug 1, 2013

By Sadan Kelebek, S. O. Fekete, Gerhard W. Heinrich, Peter F. Wells

"For many years, rejection of pyrrhotite at the milling stage has been a viable method for sulphur dioxide abatement. Pyrrhotite rejection options have included the use of selective pyrrhotite depressants in flotation; a depressant which has recently come into use is diethylenetriamine (DETA). This reagent has been the subject of recent research and development efforts in the processing of nickel-copper sulphide ores.In the present study, adsorption trends for DETA have been monitored under the dynamic conditions of flotation using a spectrophotometric method which has been adopted for this purpose at Falconbridge Limited. The results indicate that the adsorption of DETA is quite fast and in the majority of cases, accounts for the disappearance of 75-95 % of this reagent from pulp's liquid phase. The adsorption decreases linearly with an increase in the DET A dosage from 100 git to 600 git. The tailings produced in flotation tests were subjected to washing with deionized water at 60 °C to examine the desorption of DET A. These results indicate that the amount desorbed increases with increasing DETA dosage used during flotation but is less than 7 per cent of that adsorbed. It was found that adsorption of DETA alone, even at relatively high levels, does not always cause depression of pyrrhotite. A new combination of reagents identified in the metallurgical laboratories of Falconbridge Limited utilizes sulphur dioxide with DETA. These reagents together are capable of efficient depression of pyrrhotite on a consistent basis."

Jan 1, 1995

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007

By S. Southall, F. McCaffrey, F. Stober, M. Darini

Electrode Columns are commonly used in electric furnaces to deliver current and regulate furnace power to the smelting or melting process. Hatch has developed an innovative patent-pending system for lowering ("slipping") and/or raising ("back-slipping") the electrodes through an electrode column, without requiring the release of any clamping devices. All clamping forces are applied by springs. Unlike systems employing hydraulically applied clamping forces, (e.g., water bladders) the spring system is failsafe. Its inherent simplicity virtually eliminates the need for maintenance. The Hatch system is particularly applicable to Soderberg electrodes, and comprises two axially movable slipping clamps and a stationary power clamp, each of which apply a distributed, radial clamping force to the electrode. The magnitudes of the slipping sleeves' clamping forces and sequencing of their axial movements are selected such that the slipping clamps, in conjunction with the weight of the electrode, provide slipping or back slipping without release of any clamping force.

Jan 1, 2005

By G Anders

The effectiveness of two types of powder used in long-wall slashing was compared. The evaluation of the results can serve as a good example of how the application of statistical methods to underground test data can help to minimize the number of tests to be carried out. The conclusions are stated concisely, including a definite assessment of the reliability of the tests. Introduction AN assignment at the Algom Nordic mine called for a performance comparison between 70 per cent Cilgel B and 75 per cent Dygel in longwall stope slashing, particularly taking into account, in both cases, the build-up of bootlegs as dependent on hole deviation. Stopes were usually 8 to 10 ft. high and inclined at about 17 degrees. Starting from a raise, they were widened by consecutive longwall slashes to 60 ft., and, al-lowing for drift pillars, were approximately 300 ft. in length along the incline.

Jan 1, 1964

By B. McFadzean, J. Taguta

In order to recover minerals by flotation, the sub-processes of collector adsorption onto the valuable minerals followed by bubble-particle attachment should occur efficiently. This paper investigates both of these sub-processes for various thiol collectors and their mixtures onto base metal sulfide minerals. The aim of the work was to investigate whether there is a correlation between the strength of the collector interaction with the mineral and the subsequent bubble-particle attachment. The collector-mineral affinity was measured experimentally using an isothermal titration calorimeter in order to determine the molar enthalpy of adsorption for each collector-mineral system. The bubble-particle attachment was measured using a microflotation device which essentially determines the hydrophobicity of the mineral. Sodium ethyl xanthate (SEX) and sodium diethyl dithiocarbamate (DTC) and mixtures thereof were used as collectors with either single minerals or binary mixtures of pyrite and chalcopyrite, respectively. The adsorption enthalpies of the collectors were interpreted with reference to the chemical structure of the collector molecule and showed that the greater the positive inductive effect of the collector, which may be qualitatively related to their pKa, the greater their affinity for the mineral surface. In the microflotation studies, recoveries were strongly related to the alkyl chain length but there was no correlation between the enthalpies of adsorption and the flotation recoveries. When mixtures of collectors were used there was clear evidence of synergistic effects and in the case of DTC/xanthate mixtures it is possible that this synergism is related to a DTC promoted oxidation of xanthate to dixanthogen. When mixtures of pyrite and chalcopyrite were used the flotation recovery and enthalpy of adsorption of SEX onto the individual pyrite particles in the mixture increased substantially compared to the case of pyrite alone. Mechanisms are proposed to interpret these important observations.

Jan 1, 2016

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005