Search Documents

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

By Gordon Sparks, Lyle Kajner

"An often over-looked component in the assessed value of a mining property is the value derived from the ability of the operator to limit financial losses during adverse economic times (i.e. low market price, high energy prices, etc.) by suspending operations. Overlooking the value of this type of operating flexibility when conducting mine investment analysis may negatively bias the risk profile for the investment by over estimating the investment's downside potential, thereby effectively undervaluing the investment. This paper illustrates the nature of the value of operating flexibility and discusses how it may be explicitly quantified within the context of conducting stochastic mine investment analysis. IntroductionMining properties are evaluated using an array of techniques ranging from simplistic non-discounted payback calculation s to sophisticated, discounted-stochastic simulation. Stochastic simulation analysis is perhaps the most robust mine investment analysis technique as it not only provides an estimate of the expected value of the property, but also quantifies the associated risks (for examples of stochastic mine investment analysis, see: Billingsley and Yaychuk, 1986; Gentry and O'Neil, 1984; Munro, 1977; or Harris, 1970).The quantification of risk is important as it provides the necessary yardstick required to allocate the corporation's resources efficiently. Resources are said to be allocated efficiently when the corporation's expected long-term financial reward is maximized while at the same time minimizing its risk (see Hertz, 1968; or Markowitz, 1952 for in depth discussions on efficiency as it relates to investment policy). The efficient allocation of resources should be the objective of any rational corporation. Therefore, rational corporations should employ stochastic evaluation techniques when screening their investments."

Jan 1, 1992

By Hökmark. H., M. Lönnqvist

"The Swedish Nuclear Fuel and Waste Management Company are planning to construct a permanent storage facility for high-level nuclear waste at about 500 m depth in fractured crystalline rock. One potential concern for the long-term performance of the repository relates to large fracture shear displacements, since these may damage intersected waste containers. Although details in fracture surface geometries are known to influence slip magnitudes and distributions, fractures are commonly approximated as planar features with lab-scale properties due to lack of relevant field-scale data and to limitations in available modelling tools. The purpose of the work described in this paper is to explore the possibilities to use the distinct element code 3DEC to generate and analyze models with isolated, non-planar fractures and, based on the results of such models, get perspectives on the influence of basic disturbances such as ridges, steps and waves. Given the model set-up, fracture segments with orientations deviating from the critical one will contribute to stabilize the fracture. As a result, all analyzed non-planar fractures slip less than the critically oriented planar fracture. We demonstrate that the angle of deviation is the most influential parameter determining the slip magnitude for comparable surface geometries. Similarly inclined steps and ridges have almost equal slip reductions despite differences in surface area restricting the movement. Although it may be possible to translate the influence of such irregularities to an effective coefficient of friction that could be used as input to models with idealized planar fractures, additional analyses with randomly shaped and distributed asperities, different fracture sizes and with alternative stress loads, need to be carried out to devise a defensible strategy for this type of parameter variation. INTRODUCTIONThe Swedish Nuclear Fuel and Waste Management Company’s (SKB) concept for deep geological storage of high-level nuclear waste is the KBS-3 method according to which the waste will be encapsulated in copper canisters and deposited, surrounded by compacted bentonite clay, in vertical deposition holes at about 500 m depth in fractured crystalline rock (SKB 2011). A site has been selected in the Forsmark area, which is located some 120 km north of the Swedish capital Stockholm. One potential concern for the long-term performance of the repository that has been identified by SKB (SKB 2011) is related to large shear displacements along repository host rock fractures induced by a nearby earthquake, since these may cause mechanical damage to intersected waste containers. Due to lack of relevant data at the appropriate field scale and to limitations in available modelling tools, fractures are commonly approximated as planar features with lab-scale properties. The standard numerical tool, 3DEC (Itasca 2013), used in SKB’s rock mechanics analyses, for example, generates planar fractures by default. Results from dynamic 3DEC earthquake-models (Fälth et al. 2010) currently provide input to layout decisions, i.e., the diameter of the smallest planar fractures that must be avoided when deciding on waste container positions at different distances from potential earthquake faults. It is, however, well known that fracture surfaces are rough or undulating on a wide range of scales (e.g., Candela et al. 2012) and that such deviations from planarity influence the mechanical behaviour of the fractures (e.g., Dieterich and Smith 2009, Marshall and Morris 2012, Ritz and Pollard 2012). It will probably never be a realistic option to attempt to represent the geometrical complexity of a population of fractures of different size, shape and surface structure in any large-scale rock mechanical analysis relevant for the performance assessments of the nuclear waste repository. It may however be possible to find approximate ways to represent different styles and degrees of non-planarity by assigning mod"

Jan 1, 2015

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By A. Mellek, M. Pischtschan, M. Perrucci

ABB has received an order for one of the most challenging mill drive projects in its history. With one SAG mill and one ball mill to be added at an iron ore mine in Sweden, the customer’s plant managers wanted to have the most efficient solution for driving their mills but had the budget limitations typically faced by the majority of mining companies during periods of market downturn. To find the best balance between cost of acquisition and highest performance throughout the lifetime of the plant, ABB was selected to deploy a synchronized bypass solution, in which only one drive system is used for two different mills in series. However, being one of the first grinding mills in the world with such a solution was not the only challenge the ABB team faced: The inclusion of some mill application functions - e.g., frozen charge protection, automatic positioning and creeping mode - brought the demands on the engineers to another level. With only one frequency converter and one mill application controller available, the configuration logic and interlocks had to be meticulously designed and thoroughly tested to ensure a smooth and safe startup. The solution offers a footprint reduction and more operator flexibility at a reduced investment as each mill can be run in both directions, and wear on the mechanical components can be greatly reduced due to ABB’s premium ring-geared mill drive (RMD). This paper will describe the details of the project, the configuration developed and the tests performed to guarantee correct software functionality. Mill startup is scheduled for January 2016.

Jan 1, 2016

By L. Xia, B. Hart, K. Douglas1, S. C. Chelgani

Development work to optimize a flotation flowsheet for rare earth element (REE) recovery is underway. The original approach used alkyl phosphates and phosphoric acid ester as collectors to concentrate REE minerals. To improve REE recovery, hydroxamates as alternative collectors were investigated. In this paper, micro flotation of REE minerals using salicylic, benzoyl and naphthoyl hydroxamates is reported. Unlike phosphonic collectors, slime removal does not show a significant effect on REE recovery when using hydroxamates as collectors. Among the three hydoxamates, the grade of La, Ce, and Nd for concentrates produced by salicylic hydroxamate is the highest. The recovery response with naphthoyl hydroxamate is similar to that of salicylic hydroxamate; good grades for La, Ce, and Nd, less effective for Nb, Y, and Zr. The data indicated an affinity by salicylic and naphthoyl hydroxamtes for LREE over the HREE minerals. In comparison, benzoyl hydroxamate indicated an affinity for Nb, Y, and Zr. Temperature effects on REE recovery were also studied. The grade and recovery of REEs generated by flotation using a mix of salicylic and benzoyl hydroxamates at room temperature was almost identical or even better relative to the recovery using naphthoyl hydroxamates at elevated temperature.

Jan 1, 2014

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies' bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By Gary M. Bone

The autonomous control of vehicles interacting forcibly with their environment, such as dozers and tractors, is an unsolved and challenging problem. Forces and motions are inherently coupled between the tool and the means of vehicle propulsion. Furthermore, they are often operated within uncertain and unstructured environments, such as those encountered in underground mining. There is a growing industrial interest in the development of robotic vehicles to improve productivity, efficiency and safety in mining and construction. This paper focuses on the modeling and control of autonomous robotic dozing for a material removal operation. A dozing process model has been developed based on observations of both a fullscale dozer and a scaled-down version. The model characterizes the dynamic interactions between the blade position, material accumulation on the blade, material distribution in the environment, and the motions of the dozer. The dozing control objective is to remove the loose material as rapidly as possible by driving forwards at full power while automatically raising/lowering the blade in response to sensor measurements. Two different controllers were developed to meet this objective. The first controller is based on a set of heuristic rules, and the second is an optimal controller based on the dynamic model. An instrumented scaled-down robotic dozer and dozing environment, designed to emulate the full-scale operation, are used to implement the controllers and compare their performances over multiple dozing passes. Experimental results are presented showing that the model-based controller increased the material removal rate by 33% compared to the rule-based controller. Lastly, technologies for full-scale implementation are discussed, followed by proposed future work and conclusions.

Aug 1, 2013

By H. W. King

"Cryogenic engineering is concerned with components and machines which operate for long periods of time at temperatures within a few degrees of absolute zero. The absence of a ductile-brittle transition is thus the prime component of the specification for a suitable low-temperature alloy. The word "" cryo"" means ""frost-forming"" , and this leads to the second component of the alloy specification, which is resistance to corrosion in humid atmospheres. Further, although most early applications of low-temperature alloys were limited to the storage or transportation of liquified gases, an increasing proportion of alternative energy storage and conversion technologies are being based on the availability of high-field superconducting solenoids. The third basic component of the specification for a low-temperature alloy is thus the absence of a low-temperature ferromagnetic transition.Although the firs t two of these components of the specification can be met by using austenitic stainless steels, many of these supposedly "" non-magnetic"" alloys have been found to undergo martensitic transformations to ferromagnetic phases at very low temperatures. In addition, steels which remain structurally stable may still exhibit other magnetic transitions, e.g. to antiferromagnetic or superparamagnetic states. The successful application of these alloys in cryogenic engineering has thus required an initial basic study of the types of magnetic transition that can occur in such concentrated solid solutions, followed by a more applied study directed at an alloy formulation which will induce beneficial magnetic states at low temperatures."

Jan 1, 1981

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By Eric R. Skonberg

"Technology exists today to blind drill a mine shaft 20 feet in diameter, unlined, over 3,000 feet deep. These shafts must be lined in the most economical, safe and expedient manner possible. A new technique of stacking precast concrete cylindrical sections in the unlined shaft has been developed to yield a dry and hydrostatically lined shaft .These sections must withstand an external radial pressure of 3,000 feet of water yet take up as little room as possible in the shaft . Using high-strength concrete, wall thicknesses may be kept at 2 feet. The outside diameter of the sections has been chosen to be 18 feet to allow for some annular space between the liner and shaft wall. The concrete sections are produced in segments 10 feet long weighing 75 tons each. During drilling operations, the concrete sections are cast and cured. After drilling operations are complete, a headframe is situated over the shaft. The unlined shaft remains full of fluid. A special liner running tool is mated with the section in three steel ports at the bottom of the section. The section and running tool are lowered into the hole, and the tool is disconnected and returned to the surface. Subsequent sections are lowered and stacked using the same operation. Grout is placed behind the liner to result in a dry shaft."

Jan 1, 1981

By Robert B. Parsons

"The budget that was tabled by Finance Minister MacEachen on November 12, 1981 will result in a major tax reform of Canada's income and sales tax systems, the likes of which have not been witnessed by taxpayers since 1971. All segments of the economy will be affected one way or another by the far-reaching budget proposals; the mining industry did not escape untouched.Important changes will be introduced which will alter some of the fundamentals of structuring mineral resource ventures in Canada. This month, Tax Notes examines these changes, and also summarizes the other highlights of this key federal budget.IntroductionFinance Minister MacEachen's budget, with its lower personal tax rates, loophole plugging and tax shelter bashing, represents the biggest shakeup in our tax system since tax reform in 1971. In his budget, presented in the House of Commons on November 12, Mr. MacEachen proposed substantially lower tax rates for middle and upper income individuals, with the top federal and provincial tax rate dropping to about 50%, but in return he eliminated most of the opportunities for individuals, and corporations, to reduce or defer taxes through a wide variety of tax shelter and tax planning mechanisms.Although many of those budget proposals that dealt with the resource industries focused on the implementation of the September 1, 1981 agreement reached by the federal and Alberta governments concerning the National Energy Program (see Tax Notes in the December 1981 issue of the Bulletin), the budget also contained some proposed amendments that would have significant implications for investment in the mining industry.This month, Tax Notes examines these latter proposals, and also summarizes very briefly those budget proposals which are not unique to the resource sector."

Jan 1, 1982

"In flotation research, relatively little attention has been paid to understanding particle-bubble detachment phenomena compared with attachment processes. With CFD models now incorporating attachment/detachment kinetics, it is important to obtain more accurate formulations for detachment probability. The formula most often used is due to Bloom and Heindel (2002) who proposed that the rate of detachment would equal the product of detachment frequency, as previously estimated by other authors, and probability of destabilization, as estimated previously by Schulze. These two factors both account for the balance between stabilization and destabilization forces, so the product accounts for this effect twice. An integrated procedure has been followed to estimate the overall detachment rate by re-analysing the process. In this analysis, detachment rate is calculated as the frequency of eddy-aggregate interactions (or “collisions”) sufficiently energetic to cause detachment. The Bond number analysis of Schulze has been incorporated into the turbulence frequency analysis of previous authors in an integrated way. The new formulation has essentially the same type of dependencies as the previous model, but gives a lower detachment frequency. Detachment frequency has been calculated using the new formula for conditions relevant to an industrial flotation cell. INTRODUCTIONIt is well known that the effectiveness of froth flotation for separating different minerals is limited to the particle size range of approximately 10–100 mm (Trahar & Warren, 1976; Trahar, 1981). Fine particles tend to follow fluid streamlines around bubbles limiting the likelihood of bubble–particle collision, while coarse particles can be more easily detached from bubbles before collection can be achieved.Phenomenological models have been developed to quantify the physico-chemical aspects of flotation in order to better understand factors affecting these limitations, and to suggest ways of broadening the window of feasible flotation. Koh and Schwarz (2008) have incorporated these models into computational fluid dynamics (CFD) models of flotation cells, which have then been used for design and scale-up purposes (Schwarz et al., 2015). The models are based on dividing the process of bubble–particle interaction into three subprocesses: collision, adhesion and detachment. Of these, the hydrodynamics of bubble–particle collision and the probability of adhesion have been studied most extensively, while the dynamics of detachment have received relatively little attention from investigators."

Jan 1, 2016

By Daniel L. Cluff

The Canadian mining industry needs to find viable alternatives to the conventional cemented pastefill/hydraulic methods of backfilling open stopes for underground mines located within a permafrost zone. The harsh environment and the isolated location of a mine north of 60° impose additional challenges to standard backfill methods and opportunities to the technological and operational issues related to the use of frozen fill. Underground open stoping mining methods require the placement of fill material to enable the controlled recovery of ore from secondary and tertiary stopes. The typical design of the fill material requires the specification of inert material, water and binder. The permafrost conditions provide the additional parameter of subzero temperatures for backfill design and process control. The paper presents the results of an experimental field study, using large size samples, to determine the strength capacity of frozen backfill. The experimental work was performed utilizing rockfill and tailings material with moisture content consisting of water and ice crystals. Preliminary results indicate that the mixture of rockfill, tailings and moisture, develops strength that meet the demanded requirements for open stoping. A thermal equilibrium modelling analysis is presented in the paper.

May 1, 2008

By Darrell McClarty, Roger Payne, Matt Haggis, Michael Courtin, Deborah Berthelot

"Over forty years of uranium mining in the Elliot Lake region of Ontario (I 956-1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and thereby significantly inhibit acid generation have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited' s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on ""Fix Dmacs"" technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.IntroductionCost-effective management of multiple tailings management areas distributed throughout a 35 km watershed requires the application of leading-edge environmental technologies. Long-term monitoring, care and maintenance costs must first be minimized through the application of decommissioning technologies that inhibit acid generation and minimize the release of contaminants from the sites. On-going operating costs must then be controlled through the application of environmental management strategies that optimize the allocation of resources while ensuring compliance with regulatory and Company environmental requirements.Using sites in the Serpent River Watershed as an example, this paper demonstrates the effectiveness of water covers as a decommissioning strategy to inhibit acid generation. In addition, the Telemetered Environmental Operating Control System and Regional Environmental Information Management System are reviewed as examples of the application of environmental technologies to the management of environmental programs."

Jan 1, 1998

By J-F. Magnan, M-A. Thibault, R. Boulianne, C. Gauthier, J-P. Gagné, G. Dufour

During the production of aluminium in smelters, the anodes used in electrolysis cells have to be replaced frequently. Anode butts are usually placed on anode trays for transportation and cooling, a practice during which Hydrogen Fluoride (HF) is emitted in large quantities. Covers developed in 2000 by Alcoa Deschambault to fit on the anodes trays were implemented, resulting in significant reductions of HF emissions. However, the covers are expensive to maintain and use short-life consumable parts. In January 2004, STAS and Alcoa decided to develop a more efficient design of cover, with lower maintenance costs and no need for consumable materials (like soft cushions). This paper presents a summary of the work performed to develop the new design as well as a summary of the test results.

Jan 1, 2006

By L. Voisin, K. Itagaki

In the reductive smelting of the copper concentrate like a blast furnace operation using coke as fuel and reductant or in processing the copper concentrate which contains coal in the bulk, a sulfur-deficient matte phase often coexists with an iron base alloy in the bottom of the smelting furnace. This alloy is generally called furnace residue or speiss when considerable amount of arsenic or antimony is contained in the alloy and in the extreme case of reducing condition the alloy is saturated with carbon. As a fundamental study to know the behavior of some precious metals such as silver, gold and platinum between the sulfur-deficient matte and the furnace residue or the speiss which are in equilibrium under reducing condition, the phase relations and distribution of precious elements in the Cu-Fe-S-As and Cu-Fe-S-Sb systems saturated with carbon were determined at 1473 K by a quenching method.

Jan 1, 2007

By T. Hidayat

The distributions of minor elements between slag/metal and slag/matte in equilibrium with tridymite in the Cu-Fe-O-S-Si-Al-Ca system have been investigated in the range of conditions of interest to the high- temperature copper production, refining, and recycling processes. An improved experimental methodology has been used involving high temperature equilibration in controlled gas atmospheres, rapid quenching, and quantitative microanalysis techniques using Electron Probe X-ray Microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrum (LAICPMS). The effect of oxygen partial pressure on the distributions of minor elements between slag/metal and slag/matte has been accurately measured. The effects of slagging components (Al2O3 and CaO) on the distributions of minor elements between slag/metal have also been experimentally determined. The present study is a part of a larger integrated experimental and thermodynamic modelling research program in the systems relevant to high-temperature copper processing. INTRODUCTION In the high temperature processing of copper, minor elements are distributed between different phases, i.e. liquid slag, liquid matte, and liquid metal. From a processing perspective, it is desired to have the valuable minor elements distribute predominantly in the metal and matte phases rather than in the slag phase, and to have the non-valuable minor elements distribute predominantly in the slag phase rather than in the metal and matte phases. Knowledge of the distributions of minor elements between phases in the smelting, converting, and refining processes is required if the distributions of minor elements between phases in these processes are to be optimized.

Jan 1, 2019

By Heidi Fauser

The aim of the project was the development of an electroforming process for the production of medical implants out of gold. To prove the applicability of this technology, tympanostomy tubes were chosen as demonstrators. These barbell-shaped tubes are usually produced mechanically; of silicone or, for higher therapeutic demands, of metal ? gilded silver or gilded stainless steel. Gold electroforming of the tubes as an alternative manufacturing process would reduce the expenditures for the mechanical preparation and lower the corrosion susceptibility significantly. To obtain electroformed gold tubes of the desired shape, the following steps are necessary: fabrication of a negative template by drilling holes with countersinks in an insulated aluminium sheet, electroforming process, removal of the aluminium by using a sodiumhydroxide solution. For the optimisation of the shape and surface quality of the tubes respectively the simplification of the manufacturing process, various parameters were tested, e.g. aluminium quality and sheet thickness, type of insulation layer, substrate processing, hydrodynamic conditions, type of electroforming electrolyte, electrodes position, etc. The manufactured tubes were characterised in view of thickness distribution, hardness, surface roughness and purity in comparison to mechanically produced reference tubes. From the results obtained during the project it can be concluded that electroforming processes can be easily adopted for the manufacture of medical implants. The time-consuming electroforming process is by far compensated by the simultaneous production of an arbitrary number of implants.

Oct 1, 2003