Search Documents

By Yufeng Yao, Robert P. Lowell

Abstract - Conductive heat flow anomalies associated with hydrothermal sulfide mounds on the seafloor have been studied. Sulfide mounds tend to focus conductive heat flow because sulfide minerals have a greater thermal conductivity than country rock. The topography of the mound above the seafloor, however, leads to a reduction of heat flow, particularly near the center of the mound. Because the focusing effect is constant, whereas the topographic effect decreases with distance away from the center, the focusing effect dominates toward the edges of the mound. The magnitude of these effects depends upon the conductivity contrast and the height/radius aspect ratio of the mound. Conductive heat flow anomalies at sulfide mounds also result from fluid circulation within the edifice. For the active and relict mounds at the TAG hydrothermal field, which have an aspect ratio of approximately 0.3 and a conductivity contrast of 3, the heat flux through the center of the mound should be roughly 70% of the background heat flux. The maximum effect of heat flow focusing is to increase the heat flux by about 30% above background. By comparing these effects with conductive heat flow data at TAG, we find that advective processes dominate conductive heat flow at both the active and relict mounds. Advective circulation can also give rise to much larger lateral and vertical temperature gradients than would result from conduction alone.

Jan 1, 1999

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By Y. X. Li, L. R. Xiao, S. Gong, S. S. He

Porous copper and porous copper based alloys with controllable pore structure have been manufactured successfully by sintering evaporation process. This process consisted of mixing copper or copper based alloys with NaCl powders, hot pressing and final high-temperature sintering to evaporate the filler material of NaCl powders. NaCl was eliminated completely during vacuum sintering, and strong metallurgical bonding in the walls was achieved. The pores’ structural parameter (pore size, shape, and direction) and porosity can be controlled effectively. These porous copper and porous copper based alloys with controllable pore structure have great potential in many fields. Including heat dissipating materials, heat absorbing materials, chemical catalyst carriers, electromagnetic shielding materials, filtering materials, damping materials, silencing materials, battery electrode materials. INTRODUCTION The development of porous materials began in the 1960s. The research of activated carbon with high specific surface area made porous materials enter the stage of material research (Belyakov et al., 2008; Ferey et al., 2008). With the rapid development of science and technology, porous materials play an important role in material research, and gradually become an indispensable part of the material research field (Wu et al., 2012). The research of porous materials has gradually extended to metal, ceramics, plastics and glass and other fields. It has been successfully applied in many fields, such as functional materials, industrial production, aviation, medical materials, biochemistry and electronics, which fully shows that porous materials have considerable development prospects. Porous silicon, plastic porous materials and glass porous materials are the most widely used in the field of non-metallic porous materials (Capelle et al., 2012). Compared with non-metallic porous materials, metal porous materials have developed rapidly in the late 1980s and become new materials with good mechanical properties and excellent physical properties. Porous metal materials have many advantages, such as large specific surface, small specific gravity, good silencing effect, high stiffness, high electromagnetic shielding performance, good shock absorption performance, etc (Li et al., 1999; Ferey et al., 2008). Among its many applications, metal porous materials can be used as both functional materials and structural materials. In some cases, metal porous materials have dual functions and structures. It is a multi-purpose engineering material with excellent performance. At present, porous copper, porous aluminium and porous nickel are the most concerned materials (Chen et al., 2002; Yang et al., 2017; Liu et al., 2018). The preparation methods of porous copper and copper-based alloys mainly include self-propagating high temperature synthesis (SHS), capsule-free hot isostatic pressing (CF-HIP), spark plasma sintering (SPS) (Kvanin et al., 2008; Takahashi et al., 2008; Zhang et al., 2014). However, these methods can not accurately control pore structure parameters (including pore size, shape, orientation, distribution, etc.). In porous materials, pore structure plays an important role in the overall performance of materials. In order to control pore structure parameters accurately and optimize material performance, it is necessary to explore and develop new preparation technology. In this paper, the sintering evaporation process (SEP) was introduced for the preparation of porous copper and copper-based alloys. The core process of the preparation method is hot pressing and evaporative desalination. Hot pressing can make the pore orientation consistent. Evaporative desalination can ensure the complete removal of NaCl in the form of vapor in a short time, thus eliminating the corrosion of residual NaCl on the matrix metal (Gong et al., 2011).

Jan 1, 2019

By A. T. GRIFFIS, R. J. GRIFFIS

A large magnesite-talc body is locared in Delora Township, 11 km sourh-southeasr of Timmins, Onrario. The deposit occurs in part of an Archean greensrone belt dominated by volcanic and sedimenrary rocks and large bodies of ultramafic intrusions. The magnesite-talc zane is abour 1800 m long, has a maximum width of 300 m and has been drilled ro 120 m below surface. Chemical analyses of rhe main carbonate zane average 20 ro 28% soluble MgO (magnesia), 5 ro 6% rota/ iron oxide and less rhan 0.1 % CaO (lime). Mineralogically, the zane consists of approximately 54% magnesite, 28% rate, /5% quartz and 3% hematire. Perrographic srudies suggest that rhe various assemblages of magnesite, rate, quartz and serpentine were derived from a parenr serpenrinire (after dunire). An early carbonitization stage, which produced a high-magnesite, low-talc assemblage, preceded a farer decarbonitizarion stage, which formed rhe main magnesite-talc assemblage. Despite a favourably low calcium oxide content of rhe magnesite-talc rock, considerable iron in the magnesire /at rice has limited the quality of the beneficiared product: rhe besr flotation concentrate to dare yields 92 to 94% dead-burned MgO. Experimen- I L t r i i c:~:.•-4- -------- ? -_;> ,•----1---- ta/ work continues on finding a process whereby high-purity magnesia can be produced on a commercial scale.

Jan 1, 1984

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By L. A. Homeniuk, R. Bonnar

"The Athabasca Basin has been the scene of an intense exploration effort since the late 1960s, resulting in the establishment of this area as one of the major uranium districts in the world.The A thabasca Group is of Helikian age and unconformably overlies metamorphic rocks of Aphebian and Archean age. Most of the known uranium deposits have a close spatial relationship with the unconformity, graphitic meta-sediments, major northeast-trending structures and the basin edge. It should be noted that, in regard to the latter, some of the Cluff Lake deposits are exceptions.The pre-Helikian rocks underlying the Athabasca Group have been divided into six Iithostructural domains. The known uranium deposits are concentrated in the Wollaston and Mudjatik domains in the southeastern portion of the basin.The orebodies typically have a narrow high-grade portion below the unconformity and a broader, lower-grade disseminated zone in the overlying sandstone. Over-all grades average over 1% U3O8 and our estimate of known reserves totals more than 400 million pounds of contained U3O8. Some of the deposits have high concentrations of other metals, including nickel, arsenic, cobalt and gold. Ubiquitous chlorite and clay alteration is characteristic of the orebodies.Other Proterozoic basins in Canada of similar ages and having analogous geological settings to the Athabasca have received far less attention. Although little of the known uranium mineralization in these basins is related to the Helikian unconformity, there may be an exploration potential for deposits similar to those of the Athabasca basin.IntroductionThe Athabasca sedimentary basin is located within the Churchill Structural Province of the Canadian Shield in Northern Saskatchewan. The basin is elliptically shaped and is approximately 800,000 square kilometres in area.The objective of this paper is to summarize the various elements in the genesis of the unconformity-type uranium deposits of the Athabasca Basin and to evaluate the comparative potential of other Proterozoic basins to host similar unconformity-type deposits."

Jan 1, 1982

By D. M. Xue, T. B. Li

"With the increase of human engineering activities, global climate change and active plate tectonics movement, the giant landslide frequently occurred in southwest China, which caused huge property and human losses. Besides, the potential landslides pose severely threaten to the construction and operation of airports, railways, highways and power stations etc. In order to provide accurate guidance for the landslide investigation, stability analysis and mitigation, the giant landslide is redefined according to landslide volume, depth of slip surface, complexity of landslide mechanisms, and degree of landslide mitigation difficulty, and classified with the typological classification approach based on the twofold attributes of landslide behavior including formation mechanisms and reactivation features. Finally, the threefold particularity of the giant landslide is also summarized, which enables a more effective landslide mitigation design.INTRODUCTIONWith the increase of anthropogenic activities, global climate change and active plate tectonics movement such as continual uplifting of Qinghai-Tibet plateau and strong earthquakes, the occurrence of giant landslides was in ascending trend in southwest China (Huang, 2009), which caused serious destruction, and greatly endangers such engineering construction from safety, time and economic aspects as airports, railways, highways, power stations, etc. Giant landslides have huge scale, complex formation/reactivation mechanisms and mechanical behavior. They may not be identified during the hazard investigation, but may be firstly initiated or reactivated due to the following engineering activities, heavy rainfall or strong earthquakes. Consequently, the landslide mitigation is inevitable and costly. However, it is difficult to control the deformation of giant landslide with lack of a correct understanding of genetic mechanisms (Marui, 2012; Zhang, 2000) and the excessive large sliding forces of the slide blocks calculated by the conventional limit equilibrium method. For instance, the failure of anchored pile wall for the No.102 giant ancient landslide (Zhu et al., 2012) and stabilization measures for the Sidi Rached viaduct landslide(Guemache et al., 2011); four rows of piles had not prevented the occurrence of the No.12 landslide in a high fill slope in the Panzhihua airport (Li et al., 2012)."

Jan 1, 2015

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By Robert B. Parsons

"One of the disadvantages of the federal government's idea of ""taxation by consultation"" is that it seems to take longer to enact new legislation. The proposed new rules for taxing automobile benefits is one example. Here is a ball which has been batted around between government and the public several times and still has not come down to earth. Fasten your seatbelts, there may be more to come. IntroductionThe draft legislation released on April 13 contains the details of the government's current proposals on car expenses and benefits. They differ significantly from the last announced position. Finance Minister Wilson has indicated that the release in draft form will provide an opportunity for the Commons Standing Committee on Finance and Economic Affairs (the Blenkarn committee) and other interested persons to comment before the legislation is introduced in Parliament. Accordingly, there may yet be revisions.Notwithstanding the prospect of further changes, the proposed rules generally come into force in 1988. While taxpayers may welcome some of these changes, particularly the increase in the tax-exempt allowance, many must be frustrated that, at this late date, the rules for the current taxation year are not yet finalized."

Jan 1, 1988

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By G. Itoh, S. Fukasawa

The Al-Zn-Mg alloys have been known to be susceptible to stress corrosion cracking (SCC), which is based on intergranular cracking arisen from hydrogen embrittlement (HE). The mechanism of HE has not been fully understood yet. In order to elucidate the mechanism of HE, we need to investigate the behavior of hydrogen in the alloys. In this paper, behavior of hydrogen in an Al-5.8%Zn-2.4Mg alloy was investigated by means of hydrogen microprint technique, a method to visualize location of hydrogen emission from specimen surface as silver particles. One side of the tensile test pieces was electrolytically polished and then covered with photographic emulsion. Hydrogen was pre-introduced into the test pieces from opposite side by cathodic electrolytic charging for 30min. Then, the test pieces were stretched with continuing the charging. After that, the specimen was fixed, rinsed, dried and observed with a scanning electron microscope. As a result, silver particles were observed on some grain boundaries.

Jan 1, 2015

By N. Schmitt, E. Blond, F. Hild

Working linings of steel ladles progressively damage during the steel manufacturing process due to both severe thermomechanical and chemical stresses. In the framework of the coupling scheme proposed by Blond et al. (1), this study examines the effects of the thermomechanical loading on the onset of microcracking by considering that the complex microstructure of the slag-impregnated brick is fixed during the steelmaking process. The behaviour of the refractory is identified by using thermoelastic-(asymmetric)viscoplastic constitutive equations. Numerical simulations of a simplified geometry of the lining subjected to cyclic thermal loadings at the inner side are shown. Two cases are analysed, namely, i) the material is a homogeneous continuum with a thermoelastic-(asymmetric)viscoplastic behaviour, ii) the material is porous and saturated by liquid slag, and the skeleton has the previous non-linear behaviour. The stress and strain fields are shown, and for the porous medium the interstitial pressure of slag as well. Comparisons between these assumptions are made to assess the role of slag on the degradation of the working lining.

Jan 1, 2004

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By C. Bazin, D. Hodouin, M. Ounpuu

Sensors are now available in mineral processing circuits to monitor pulp flowrate and density, as well as ore characteristics and other process variables. The amount of information provided by these instruments is considerable but in many cases poorly exploited. This paper gives the results of the application of time series analysis techniques to signals generated by the sensors installed on an industrial Pb dezincing flotation circuit in New-Brunswick. Autocorrelation and cross correlation functions appear to be interesting tools for a preliminary circuit analysis, however the calibration of single input single output discrete transfer functions using collected sensors signals leads to conflicting results. For this reason a phenomenological approach, based on the kinetic and transport properties of the flotation process, is also considered. It has several advantages over the empirical transfer function modelling but also limitations in its applicability to industrial processes. A combination of the transfer function and kinetic modelling approches appears to be a promising avenue for better process modelling and control.

Jan 1, 1985

By S. Vézina

"Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/ communication technologies, better educated populations, climate change, longrange transport of toxics, and the increasing influence of non-governmental organizations (NGOs) and multistakeholders.As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental management systems (EMS) have been introduced not only to meet the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO 14 001) is a common practice.Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities, and a variety of government infrastructures to obtain a “license to operate.” This paper presents the structure of Cambior’s EMS and how it was adapted and implemented in the company’s operations in South America."

Jan 1, 2006

By D. Perednis

Fuel cells with thin samaria-doped ceria (SDC) electrolyte films deposited onto an anode support using spray pyrolysis were fabricated. The SDC films were deposited onto porous NiO-YSZ substrates at deposition temperatures between 400°C and 450°C. The influence of process parameters such as deposition temperature, flow rate, type of salt and salt concentration on the quality of the film was studied. A smooth dense film was successfully deposited using the precursor cerium ammonium nitrate and samarium nitrate dissolved in butyl carbitol (33.3 vol.%), 2-methoxy-l-propanol (33.3 vol.%), and ethanol (33.3 vol.%) solvent mixture. A deposition rate of 125 nm/h was achieved.

Jan 1, 2005

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By Greg Gosson, Larry B. Smith

"These are heady times for the mining industry, with strong metal prices, investor enthusiasm for the junior explorer and ready access to finance for mineral projects. Many projects were shelved in the past because of technical deficiencies — insufficient tonnes or grade, metallurgical problems, the deposit was too deep or too narrow, or the project was physically or economically under water. With the possibility of sustained metal prices, now is the time for those previously “challenged” projects to be re-evaluated and financing sought for continued development. The question is, do these deposits have reasonable prospects for economic extraction, as required by all mineral resource reporting codes? NI 43-101 defines a mineral resource as that portion of the mineral inventory that has reasonable prospects for economic extraction. However, a mineral resource is not simply an inventory of all blocks above a given cut-off grade. The spatial distribution and geological and grade continuity must also be considered. The qualified person (QP) must consider factors significant to project economics at the mineral resource estimation stage, and not just when qualifying mineral reserves. CIM Best Practice Guidelines for estimating mineral resources require the factors significant to project economics be current, reasonably developed and based on generally accepted industry practice and experience. In establishing the cut-off grade, it must realistically reflect the location, deposit scale, continuity, assumed mining method, metallurgical processes, costs and reasonable long-term metal prices appropriate for the deposit. Variations within the resource model (rock characteristics, metallurgy, mining methods, etc.) may necessitate more than one cut-off grade or economic limit in different parts of the deposit model. There must be sufficient knowledge of the metallurgical characteristics of the deposit, which should be supported by preliminary metallurgical test results."

Jan 1, 2003

By A. Galley, R. Tosdal, F. Robert

The Canada Mining Innovation Council (CMIC) Exploration Innovation Consortium developed a 10-year business case for developing new discovery criteria, exploration techniques, and better data management and analysis to improve exploration success in deep, remote, and covered terrains. Within this context, the CMIC devised a five-year project proposal to create improved multiparameter exploration tools to detect ore systems and more efficient vectoring toward high-grade mineralized cores. The Footprints project was approved March 2013. More than CAD$13 million funding was provided through the CMIC-led joint sponsorship from 30 companies and the Natural Sciences and Engineering Research Council. Consistent industry leadership and integration of dedicated industry and academic expertise has the project on track for reaching its well-defined objectives.

Jan 1, 2014

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023