Search Documents

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By R. W. Coburn

The results of field experiments on wells which required stimulation indicated that engineered well-completions will cause an increase in ultimate recovery at reduced costs. Techniques and tools have been developed which can be used to establish well conditions most conducive to successful stimulation. Cementing, perforating and treating are bound together so completely that the success of one phase is completely dependent on the .effectiveness of the preceding phase. A method of determining the efficiency or effectiveness of any given well-stimulation treatment has been derived. Pressure behaviour during a treatment can be analyzed to yield the total percentage of the formation which has been treated.

Jan 1, 1960

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By Pritii Tam Wai Yin, Tony Leong, Neetu Bansal, James Vaughan, Amiel Boullemant

Mercury is a toxic element that is associated with many industrial activities including the Bayer process. Mercury is known to enter the Bayer process with the bauxite feed material and has the potential to accumulate as the process solution is recycled. This paper explores the speciation of mercury in Bayer process streams. The process parameters considered are the oxidising-reducing potential, basicity and temperature. The results of a refinery circuit survey are presented and compared with the thermodynamic predictions. Electrochemical measurements on relevant synthetic systems are also included.

Jan 1, 2014

By J. A. Finch

"This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified. IntroductionThis paper summarizes the findings of a detailed review of available technical information on the operation of rod mills. One of the basic problems in historical comminution testwork has been the lack of a standard measure of circuit performance. The Bond Operating Work Index, not introduced until after 1950, has proven of immeasurable value in this regard, but first has to be carefully considered in terms of its utility and limitations. Its prescribed use is described in a later section of this paper.During this review, it became apparent that rod mill performance is generally not well understood. Because of combined interactions, the effects of different operating variables may be difficult to assess, and even at times appear erratic. It is obviously difficult to rationalize plant testwork or circuit adjustments when the results are highly unpredictable. The purposes of this review, therefore, were:a) to establish what basic facts have been learned about rod mill performance;b) to define some genera l guidelines for efficient rod mill design and operation; and,c) to establish a basis for specific recommendations for plant tests or adjustments with minimum risk, and maximum potential for circuit performance improvement."

Jan 1, 1986

By Robert Macdonald, William Coombe, John F. Lewry

Gold occurrences have been known in the La Ronge Domain for many year . Mineable reserves have more recently been outlined and there is every prospect of a major gold camp being established in the domain within this decade. The La Ronge Domain lies in the Lower Proterozoic 'Trans-Hudson Orogen' and is part of a collage of Early Proterozoic crust comprising volcanoplutonic arcs, batholiths, associated volcaniclastics and volcanogenic sediments lying between the Superior Craton to the outheast and the reworked Archean basement/Aphebian cover terrain to the northwest. The domain has several lithostructural subdivisions, the most important of whjch , from a gold exploration point of view, is the Central Metavolcanic Belt. This belt is composed dominantly of a range of metavolcanic rocks and gabbroic to granitic intrusives, which geochemically resemble younger subduction-generated 'primitive' arcs developed on oceanic crust. U-Pb zircon geochronology indicates that the arc volcarusm and pre- to late-kjnematic plutonism occurred about 1890 Ma to 1850 Ma ago. The belt has an attained grade of upper greenschist to amphibolite facies and is relatively undeformed , though high strain zones occur locally. Most gold occurrences in the La Ronge Domain have been found in the Star-Waddy Lakes area of the Central Metavolcanic Belt, and in the Sulprude-MacKay Lakes area to the south which is interpreted as a tectonically dismembered part of the main belt. Both tratiformand vein-type gold occurrences are present in the domain; vein-type predominate and form nearly 90 per cent of the occurrences. The stratiform-type occurrences show a regional lithological a sociation with iron-rich sediments within proximal felsic volcanjc sequences. Some vein-type occurrences appear related to brittle fracturing associated with intrusive emplacement (the magmatic-hydrothermal "syn:' and "subvolcanic" veins) and faulting. However, most of the vein-type occurrences exhibit a spatial association with regionalscale ductile shear and other high strain zones, and were probably formed by metamorphichydrothermal processes.

Jan 1, 1986

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract -A test survey using the MEGATEMII airborne electromagnetic system was flown over the Iso and New Insco massive sulfide orebodies in the Rouyn-Noranda mining camp, Canada. The results were compared with data from historical systems (INPUT, DIGHEM) used to discover the deposits. The historical data show that the two deposits have comparable conductances. However, the modern MEGATEMII system reveals that the New Insco deposit has a much slower decay than the Iso deposit, and it is, therefore, interpreted to be more conductive. The MEGATEMII anomaly maps provide estimates of the location, depth, dip, and strike of the two deposits, information that was not available from the historical anomaly maps. The signal-to-noise ratio of the MEGATEMII data is greater than the historical data, yielding more sharply defined anomalies. The investigations also included a comparison between 90 Hz and 30 Hz MEGATEMII data. The 90 Hz data were found to be useful for mapping the less conductive parts of the Iso body, whereas the 30 Hz data demonstrated that the New Insco body is more conductive. Analysis of height attenuation data over the Iso body indicates that the body could be seen by the MEGATEMII system if it were buried an additional 230 m deeper (in highly resistive material). On the other hand, the INPUT system would detect the Iso body only if it were buried no deeper than an additional 60 m. Tests with the transmitter turned off showed that, for this flight, the MEGATEMII system noise levels on the processed data are about 300 pT/s. Sommaire - Dans le cadre d’un projet de recherche, un ensemble de levés d’essais électromagnétiques aéroportés employant le système de MEGATEMII a été effectué au dessus des dépôts d’Iso et de New Insco, Rouyn-Noranda, Canada. Les données ont été comparées avec les réponses des systèmes qui ont découvert ces deux dépôts (INPUT et DIGHEM). Les données antérieures montrent que le dépôt d’Iso a une conductance comparable à celle de New Insco. Cependant, les données de MEGATEMII démontrent que le dépôt de New Insco a une haute valeur de la constante de décroissance, ce qui reflète une plus forte conductivité. La carte d’anomalies de MEGATEMII indique la localisation, la profondeur, le pendage et l’orientation des deux dépôts, ce que la carte d’anomalies antérieure ne montrait pas. Le rapport de signal à bruit de MEGATEMII est plus grand que celui des données de INPUT et de DIGHEM; de plus, les pics sont mieux définis. Les tests ont également permis une comparaison entre les fréquences de base de 90 Hz et de 30 Hz. Les données de 90 Hz se sont montrées utiles pour cartographier la partie du dépôt Iso dont la conductivité est la plus faible, tandis que les données de 30 Hz montrent clairement que le dépôt de New Insco est plus conducteur. Les analyses de l’atténuation du signal avec la hauteur ont indiqué que le dépôt d’Iso pourrait être détecté par le système MEGATEMII s’il était enfoui à 230 m sous la surface (dans un milieu hautement résistant). D’autre part, le système INPUT pourrait seulement détecter le dépôt d’Iso s’l était situé à 60 m de profondeur. Les tests avec l’émetteur fermé démontrent que le niveau de bruit est des l’ordre de ±300 pT/s."

Jan 1, 2006

By W. Dingley, G. R. Hoey

"AbstractWear of six types of grinding balls was compared with and without corrosion inhibition in grinding Ni-Cu sulphide and hematite ores in laboratory ball mills. Forged steel balls (Rc 60 to 65) and three types of white cast iron balls (Rc 50 to 65) were susceptible to corrosive wear and two types of stainless steel balls [AISI Type 440C (Rc 65) and AISI Type 302 is; 35)] were relatively immune. The relative wear rates of the five types of hard balls (Rc 50 to 65) were dependent on the corrosivity of the ore. Ranking of the hard balls with respect to wear resistance was consistent for the sulphide and hematite ores in the presence of corrosion inhibition, whereas their ranking was different for the two ores in the absence of inhibition.The electrochemical potential of the grinding balls was measured during grinding and was found to be a useful measurement for assessing the susceptibility of an alloy to corrosive wear. Reduction of ball wear for forged steel and white cast irons with corrosion inhibition was concomitant with a shift of ball potential to less active values. Ball potentials in the presence of inhibition were indicative of non-corroding metal surfaces.IntroductionA PREVIOUS STUDY by the authors (1) showed that corrosion inhibitors - sodium nitrite, sodium chromate and sodium metasilicate - reduced wear of forged steel grinding balls by up to 49% in grinding Ni-Cu sulphide ore. Although the mechanism of wear reduction was not elucidated, it was concluded that corrosion must play a significant role in the wear of grinding media. Remark and Wick (2) of Battelle Pacific Northwest Laboratories have also evaluated corrosion inhibitors for the reduction of metal wear using abrasive and n on- abrasive te sting procedures. Their research was sponsored by 16 companies throughout the world. Preliminary results indicated that anodic inhibitors prevent from one-fourth to one-half of the loss due to corrosion."

Jan 1, 1977

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948

By A. Rodriguez-Prado, P. Kuschk, R. L. Legge, W. C. Lennox

Using constructed wetlands to chemically reduce hexavalent chromium Cr(VI) to Cr(III) from industrial and mining wastewater has proven to be feasible and efficient. Applying first-order kinetics to describe the process is simple, but in some cases a more accurate model is required to reflect the process. This paper studies the feasibility of using non–first-order kinetics to describe the reduction process. Results indicate that half- and second-order kinetics adequately described Cr(VI) reduction in laboratory wetland mesocosms. The organic carbon content played a relevant role, whether it was built up by plant growth or spiked into the feed water.

Jan 1, 2014

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various complex ore deposits and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides and other phases for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay & Gorain, 2014; Chattopadhyay et al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2017

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By B. F. Haanel

IN the fall of 1929, a paper was presented at the Annual Western Meeting of the Institute entitled The Fuel Research Laboratories at Ottawa and the Scope of Their Investigations. At that time, the equipment of the laboratories had not been completely installed, but the regular routine work was being carried on as usual, and several large-scale investigations were being conducted. It is now five years since that paper was presented, and it seems fitting that a brief description of the investigations which have been undertaken, together with results-especially those which have reference to western Canadian fuels-be presented at this Annual Western Meeting. The coal mining industry of western Canada has, within the past few years, suffered many unfortunate vicissitudes. The replacement of coals by oil, for bunkering ships, for operating railway locomotives, and for heating, has weighed heavily on the coal mining industry of British Columbia and Alberta generally, but more particularly in the Crowsnest Pass area and Vancouver-and hydro-electric developments have also left their impress. With a full appreciation of these conditions, the Department of Mines planned research and large-scale investigations which it was considered would be of the greatest benefit to the coal industry, and the results have amply justified the plans and anticipations. The fact, however, must not be lost sight of, that the application of the findings of certain of these investigations would not have been feasible had not the Federal Government assisted the transportation of coal by the application of railway subventions. These subventions permitted Canadian coals to compete at competitive points with United States coals, and it must be admitted also in this connection that certain of the collieries which have benefitted, both as a result of the railway subventions and the investigations conducted by the Fuel Research Laboratories of the Department of Mines, made special efforts to produce a coal which was capable of competing with the American product, by special preparation at the mines.

Jan 1, 1936