Search Documents

By C. Cutts, K. Wheatley

The Dragon Lake Zone (uranium prospect) comprises a N160º trending vein that is approximately 110 m long, up to 5 m wide and from 1 to 40 m high. The zone is mostly within altered sandstone of the Fair Point Formation, the basal unit of the Paleoproterozoic Athabasca Group, but it also extends downward (up to 3.5 m) into basement rocks that occupy the northerly trending Maybelle River Shear Zone (MRSZ). This subvertical shear zone separates graphitic paragneiss and weakly deformed granitoid rocks to the east from non-graphitic paragneiss and foliated granitoid rocks to the west. The Dragon Lake Zone cuts across both the MRSZ and N060º-N070º-trending cross-faults that offset the shear zone but not the mineralized vein, which contains values up to 54.5% U over 50 cm core length. Strong chloritization occurs in graphitic paragneiss and sandstone adjacent to mineralization. Silica was depleted from the basement rocks and redeposited at the borders of the 5-15-m-wide alteration zone, as well as within overlying sandstone of the Manitou Falls Formation. There are minimal alteration effects in the overlying Lazenby Lake Formation. Geochemistry shows that the alteration zone in the Fair Point Formation is highly anomalous in metals, most notably in Ni, As, U, Pb, Co, and B. Clay within this zone is illitic and Fe-rich chlorite is also present. Brittle deformation is not as widespread or as well developed in the Fair Point Formation as it is in the overlying Manitou Falls Formation, which is extensively brecciated and contains some anomalous metal values.

Jan 1, 2013

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By D. Want

In titanium-lined autoclave design the most critical point of its mechanical reliability is its titanium batten strips present at the circumferential and longitudinal barrel-weld seams. Recently an Australian Company, W.E. Smith Hudson (WESH) P/L, has developed a fully flush batten strip and is building autoclaves with this design. Significant research and development has been performed in the process. In this presentation, design aspects of these batten strips are presented that cover topics such as residual-stress magnitudes during fabrication, affect of preheat during batten-strip welding and residual stress in respect to fatigue life. There has been little research done regarding the affects of residual batten stress in relation to fatigue life. Considerations of this 'grey' area of design will be discussed based on the author's research data and finite element analysis.

Jan 1, 2005

By D. R. Spink

An historical background is presented to provide a basis for the lack of normally expected developmental effort over the first 20-25 years of viable zirconium production operations. This is followed by a description of developing technology, which is the result of years of research and piloting effort directed to the development of a more economical method to produce high-grade metallic zirconium. It is predicted that many of the process improvements described will have a significant impact on future zirconium production methods and consequently on future prices and markets.

Jan 1, 1977

By Neil Campbell

"The gently-dipping Devonian dolomite beds south of Great Slave lake in northern Canada are nearly every-where concealed by a cover of glacial drift and muskeg. Nevertheless, in 1898 or earlier, four small outcropping areas of dolomite, richly mineralized with lead and zinc sulphides, were discovered. Exploration work performed here up to the end of 1930, included intensive trenching and drilling of the showings, together with mapping and wide-spaced drilling in the surrounding region. This work proved that the discoveries are isolated pockets of mineralization much too small to be commercially valuable by themselves. No evidence of orebodies elsewhere was reported.Meanwhile, mapping by the G.S.C. in the Shield far to the east disclosed major Precambrian faults, some of which can be projected southwesterly (under a cover of Paleozoic sediments) to the vicinity of Pine Point. During the period from 1940 to 1947, consideration was given, by The Consolidated Mining and Smelting Company Ltd., to evidence of a theoretical possibility that, although apparently dormant in Paleozoic times, these faults may have provided a structural control and a source of ore-bearing solutions in some post-Devonian period. From this, it was postulated that the breaks might have created, in the overlying dolomite, a linear array of orebodies concealed by overburden but lying in a belt of considerable length and in a position predictable within practical limits. A program of drilling designed to test and exploit this specific concept was conducted from 1948 to 1955.he drilling within the new, theoretically-defined search area resulted in the discovery of many lead-zinc ore-bodies, none of which was exposed at the surface. Some of these are large and (as indicated by 1965 production records) very rich. They are situated 1 to several miles distant from, and apparently not connected to, the earlier-known surface discoveries. The drilling also disclosed that the ore, which consists of disseminated sphalerite and galena replacements together with colloform sphalerite and coarse galena cavity fillings, occurs mainly at certain stratigraphic horizons within a large, coarsely-recrystallized dolomite barrier reef. Considerable fracturing and folding was found. It has been suggested that reef development was influenced by post-Precambrian tectonic movements associated with the old faults in the basement complex. The ore may have been deposited by solutions moving from distant sources to favourable structural and chemical environments in or related to the reef.In more recent exploration performed in the course of preparing for mining production, the rate of ore discovery within the same general geological context has been greatly accelerated by the use of new geophysical techniques and drilling equipment. Reserves of 21.5 million tons, averaging 4 per cent lead and 7.2 per cent zinc, were reported in 1965, and production from open pits at the rate of approximately 248,000 tons of concentrates per year is in progress"

Jan 1, 1966

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By B. C. Tripathy, S. K. Padhy, R. K. Paramguru, Pinak Patnaik

"Cobalt is regarded as technology enabling metal among the less abundant metals found in the earth crust. Electrodeposition of the metal from aqueous sulphate solutions is the preferred technology for its commercial production. Certain additives are added in the electrolytic bath during electrodeposition for the production of uniform, smooth and bright deposits of cobalt metal with higher current efficiencies and lower energy consumptions. A detailed investigation has been carried out to determine the effect of additive Sodium octyl sulphate (SOS) on the electrodeposition of cobalt. The results indicated that the additive apart from increasing the current efficiency enhanced the quality of cobalt electrodeposits. A maximum current efficiency of 98.4% was achieved at 10 mg/L SOS. The presence of SOS in the electrolytic bath did not result in any noticeable change in the crystal orientation of the cobalt electrodeposits except at higher concentrations (50 g/L) of the additive. Scanning electron micrographs indicate that smooth, compact and uniform deposits of cobalt were obtained at 10 mg/L of the additive beyond which there is detoriation in the quality of deposits. Polarisation of the cathode was seen in the presence of SOS. The effect of SOS on the electro kinetic parameters: Tafel slope (b), transfer coefficient (a) and exchange current density (I0) has also been investigated.INTRODUCTIONCobalt is recognised to be a strategic metal among the various base metals, owing to its numerous applications in various industries. Cobalt as a metal finds its use in the preparation of rechargeable batteries, as an alloying component in the manufacture of space craft and jet engines, as a drying agent for paint varnishes, ground coats for porcelain enamels and in the manufacture of the catalysts for the petroleum and chemical industries (Davis, 2000). Although there is a huge demand of the metal the supply of the metal is limited due to its scarcity in the earth crust. The metal comprises of only 0.02% of the earth’s crust for which the metal is recovered from various ores of nickel and copper as a byproduct (Hawkins, 1998). The present day techniques for cobalt production includes mostly hydrometallurgical methods which are preferred over the earlier used pryometallurgcial methods carried out for the metal production. Almost 70% of the world’s cobalt produced currently is from hydrometallurgical techniques in which electrodeposition of the metal from aqueous solutions is the final step for metal production (Verney, 1988). The most preferred route for electrodeposition of cobalt metal involves a sulphate medium (Das and Subbaiah, 1984; Lenthall and Bryson, 1997; Sharma et al., 2005)."

Jan 1, 2016

By W M. Gilchrist

This paper gives an estimation of the future requirements of the western world in relation to energy re-sources. It then goes on to outline the role that atomic power -with its basic raw material, uranium -will play in supplying these energy requirements. Canada's position in this picture is covered, and some interesting forecasts are made. Introduction I T is possible that the following remarks will appear to have more to do with power than uranium. However, to fully comprehend what is in store for the Canadian uranium mining industry, we must be able to estimate the potential requirement, and, to do this satisfactorily, a thorough understanding of the circumstances that will give rise to that demand is necessary. The growing need for electrical energy will play by far the major role, as large tonnages of uranium will be required for its generation. The nuclear weapon has, up to the present, comprised the major market for uranium.

Jan 1, 1964

By W. S. Tremaine

When the Hedley Mascot mill was built in 1935, it was designed as a straight flotation plant. The ore to be treated at that time was a gold ore in which the gold was intimately associated with arsenopyrite and pyrrhotite in highly silicified and garnetized limestone gangue. This material was ground to 85 per cent minus 325 mesh in two-stage grinding and floated in standard flotation cells to produce about a 5-ounce concentrate, which was shipped to Tacoma smelter for refining. This arrangement gave us a recovery of about 89 per cent. Test work indicated that the best way to improve this recovery would be to build a cyanide plant to treat our flotation middling. Arrangements for the construction of this plant were finally approved and work on it was started in the spring of 1940. This plant was of the conventional type in which the flotation middlings were thickened, filtered, and then put through the usual cyanide process. Its capacity was 50 tons of middlings per day. This arrangement worked quite satisfactorily and gave us an increase in overall recovery of 4 per cent. Unfortunately, about the time the plant was completed, we developed, and started to ship to the mill, ore that differed entirely from that met with up to that time. Instead of being hard, it was very soft, the orebody from which- it came being much faulted and brecciated. In many sections, the sulphides were oxidized and the breccia was filled in with a very soft, hydrous iron silicate known as chloropal. When this new ore was mixed with the old ore and sent to the mill, the whole operation was disrupted. The chloropal slimed so badly that the classification, flotation circuits, and cyanide plant would not handle it. The difficulty in the cyanide plant was at the head end, where the 10 ft. by 20 ft. thickener and the 8 ft. by 8ft. drum filter would not handle the middlings containing a large percentage of primary slime and chloropal. This material would not thicken to more than 30 per cent solids in the thickener and, when pumped to the filter, would forma very thin, slimy cake. Overall recovery dropped to between 83 and 84 percent and it was quite apparent that some extensive changes would have to be made in our flow-sheet before this ore could be treated successfully.

Jan 1, 1947

By W. Gordon Muir

This paper deals with the exploration, development and current operations of the salt mine at Goderich, Ontario operated by the Sifto Salt Division of Domtar Chemical Limited. The rock salt is obtained from a bed 1,760 feet below the surface, 75 feet thick, extending under Lake Huron. Annual production is in excess of one million tons. Large mobile equipment is used. Details of this equipment, as well as the shaft layout, which permits the equipment to be lowered underground with a minimum of trouble are outlined. Mining, crushing and screening procedures' are rev1ewed. Reference is also made to productivity salt distribution and uses.

Jan 1, 1967

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

By Geology Staff, C. H. Stockwell

"The Flin Flon base metal mine, owned and operated by the Hudson Bay Mining and Smelting Company, is on the Manitoba-Saskatchewan interprovincial boundary at a point 400 miles north of the International boundary. The deposit was discovered in 1914 by Thomas Creighton and the Mosher and Dion brothers. Since production commenced in 1930, 25,000,000 tons of ore have been mined. On January 1st, 1946, reserves were estimated to be 26,000,000 tons, averaging 2.99 per cent copper, 4.i4 per cent zinc, and 0.089 oz. gold and 1.25 oz. silver per ton. In addition to the four metals named, others recovered from the ore include- cadmium, selenium, and tellurium. The mine workings extend to the 3,750-foot level, but little development work has yet been carried on below 3,250 feet.The known ore occurs in six lenticular to irregular bodies within a zone 500 feet wide. These bodies average 900 feet long, 70 feet wide, 1,500 feet in vertical depth, and 2,500 feet in length along the plunge. They were formed by replacement of the country rock and include ore of two types, solid sulphides and disseminated sulphides. Seventy per cent of the total known ore is of the solid sulphide type. This consists essentially of metallic sulphides- chiefly pyrite- with included remnants of the host rock, and additional quartz and carbonate. In places, the ore exhibits banding, inherited from pre-existing structures. The disseminated ore occurs usually on the footwall side, and along the bottom of the plunge, of the solid sulphide bodies."

Jan 1, 1954

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By A. C. Hawken, L. M. Strah

"The Report outlines the Conversion to Rubber Mill Liners and steel grinding balls from the old style Cobalt pocket liners and flint pebbles which had been used in 5'x22' Fraser-Chalmers tube mills for over fifty years. An outline of the past history and some of the plant modifications are mentioned as well.The details pertaining to considerations, modifications and repairs carried out on the mills are described. Factors influencing the rubber liner design are outlined along with the description of the rubber liner design.The performance and advantages to date are given and concludes with brief summary.HISTORYThe original amalgamation-cyanidation mill of Dome Mines Limited went into operation in 1912. Milling has been continuous since 1912, except for two periods; one of 17 months commencing in December 1917, and the other of about 12 months, when fire destroyed the plant in November 1929. Initially the capacity of the mill was 350 tons a day. In 1916 it was raised to 750 tons a day, following which there was a gradual expansion to 1,500 tons a day."

Jan 1, 1977

By Sean McClenaghan

Significance Setting Size Production Value History of Discovery Zn and Pb at Austin Brook Brunswick Belt Exploration Discovery Hole Geology Structure Metal Zonation Directed Research Incremental Ores Precious metals Closure and Beyond Mining Remnants Tailings

May 1, 2013

By J. S. Fox

Major-element data for unaltered, unmineralized felsic host rocks from a number of stratigraphically simple, massive volcanogenic Zn-Cu(-Pb) sulphide deposits of low metamorphic grade have been compiled. The petrochemical affinities of these host rocks have been determined (by standard means and by discriminant analysis) and compared. This comparison indicates that volcanogenic deposits in felsic terrains are not restricted to the classical calc-alkaline rock association as previously thought, but can actually be hosted by rocks showing a range of iron content. There is a positive correlation between differentiation trend and are tenor. Zn-Cu ores usually have iron-rich felsic hosts (most Canadian Shield deposits); Pb-Zn -Cu ores have iron-poor felsic hosts (Japanese, Iberian and Tasmanian deposits). This parallels the antipathetic relationship between iron content and background lead levels evident in young, unmineralized, island arcs as well as in many older belts. Correlations between differentiation trend on one hand and massive ore mineralogy and the relative proportions of various rock type (including rhyolite, quartz-porphyry and coarse pyroclastic rocks) on the other are also evident. It is concluded that the recognition of a calc-alkaline differentiation trend cannot be used as a prospecting guide, as has previously been proposed. However, in view of the above correlations, the recognition of a given trend may aid in the formulation of an effective exploration philosophy.

Jan 1, 1979

By Reik M. Winkel

Radar Technologies are successful implemented in the military industry since decades and recently found their way in the mining industry as level gauge radars for bin applications. The latest generation of microwave radar sensors are capable to provide geometrical data of the surrounding area of mining machines, too. Radar sensors are an improvement to laser scanners as they are more robust and able to penetrate dust and mist. Radar sensors will be the key source for operator assistance systems. indurad and RWTH Aachen University conducted a large series of tests at open pit mines and underground coal mines to determine the potential of the new two dimensional Dual Range Radar iDRR. Several applications were determined as highly feasible and are now completed respectively in the implementation stage. The authors are giving an insight in the experimental results, the implementation and an outlook of future applications for this technology.

Oct 1, 2009

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By Anita Marks

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By Michael Samis

The real option valuation method is often presented as an alternative to the conventional discounted cash flow (DCF) approach because it is able to recognize additional project value due to the presence of management flexibility. However, these two valuation methods can be separated on a more fundamental level by their differences in risk discounting. Real option valuation applies the risk-adjustment to the source of uncertainty in the cash flow while the DCF method adjusts for risk at the aggregate level of net cash flow. This seemingly small difference is the reason why the real option method is able to differentiate between projects according to each project?s unique risk characteristics while the conventional DCF approach cannot. This paper provides an overview of the real options and DCF valuation frameworks and discusses the differences in risk discounting that exist between the two methods. Using grade-school mathematics, this paper clearly demonstrates how, with real options, a unique project risk discount can be calculated which is directly linked to the project?s unique risk profile. It also highlights why the DCF method fails in this regard and shows why a call to ?increase the Risk-Adjusted Discount Rate? is an incomplete solution at best. Finally, a heap-leach project and satellite reserve development project are valued with both techniques and the difference in investment conclusions is explained in terms of the risk-discounting concepts discussed here.

May 1, 2003