Search Documents

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By John Drew Ridge

"Over the years, ore geologists have made innumerable observations as to the relationships of certain kinds of ore deposits to particular types of rocks and to the types of primary and secondary structures that these rocks contain. On the basis of these, the places in which to look for new are deposits are more clearly defined than they would be in an exploration program based largely or solely on concepts of ore genesis. This paper discusses the affinity of certain rock types and structures for such ore deposits as: (1) tin-tungsten associated with granitoid rocks; (2) lead-zinc of simple mineralogy in carbonate rocks; (3) massive base-metal sulphides in sedimentary or volcanic rocks; (4) massive base-metal sulphides and oxides at, or near, contacts with igneous rocks; (5) gold or gold-uranium in, or adjacent to, conglomerates; (6) shale- or sandstone-hosted copper; and (7) porphyry coppers. Additional varieties could be considered, but it appears that these examples are sufficient to demonstrate the validity of the suggestion that the use of observational characteristics is far more useful in mineral exploration than that of theories of ore genesis.As by-products of the theory of plate tectonics, many concepts have been put forward to explain how ore deposits of different kinds have been formed. Most, if not all, of these theories seem to be as valid as present-day information permits. However, do these ideas add to the ability of the ore geologist to find ore deposits? I doubt it, and offer reasons as to why I think so.To produce maximum results in any exploration program, the one that makes the greatest use of information produced about the geologic environment of the area being investigated is the one that will provide the greatest return in deposits found for the sponsors of the program. Such exploration is best designated as total exploration, and it certainly is the most effective way of uncovering such new deposits as may exist in the area being studied in particular and of adding to the sum total of nonfuel minerals deposits available to the industrial world in general."

Jan 1, 1983

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By Rita Michael

"The Marmara Ironworks was not the earliest ironworks in Ontario, but it was distinguished from other early works in a number of ways. It was established on an ambitious scale as a self-sufficient and, for the time, sophisticated community. In effect it was an iron plantation on the scale and scope of those at Hopewell, Pennsylvania and Saugus, Massachusetts(1). It was, besides, the only one of the few early ironworks in Upper Canada which operated almost to the end of the nineteenth century, albeit in fits and starts, and which used magnetic ores rather than bog iron ores (limonite). Furthermore it is the only works which has produced archaeological interest over a number of years. The ironworks is on the east bank of the Crowe River near Highway 7, on Lots 7 and 8, Concession 4, Marmara Township, Hastings County, Ontario. It is the property of the Village of Marmara, and the extant remains encompass about 2. 5 acres of the original 2000 or so which made up the original grant. The mineral riches of the Canadian Shield had been known since the days of the Jesuit missionary-explorers. A consortium headed by Alexander Henry and the Duke of Gloucester planned to exploit the copper near Sault Ste. Marie during the last part of the eighteenth century, but nothing came of the venture(2). This attempt may have grown out of Lord Dorchester's suggestion that private enterprise be encouraged in order that the iron ore which ""abounds"" in Canada might be exploited(3). John Graves Simcoe, the first Lieutenant Governor of Upper Canada was also anxious to see iron working develop. Simcoe was eager to encourage many enterprises, among which ""the development of iron mines""(4) - Governor Gore had been approached by John Mason for help with his ironworks in Norfolk County (5). Three Americans had applied for permission and support to erect an ironworks on the Gananoque River at the falls to become known as Furnace Falls. They were granted 1000 acres of land in fee simple to encourage their endeavor(6). Sir Peregrine Maitland, only a few months after taking up his duties as Lieutenant Governor in 1818, intended to visit the ""bed of iron ore on the Crow River"" (7) - Maitland was to provide a good deal of support, both moral and substantive, to Charles Hayes when he came to Canada in 1820."

Jan 1, 1999

By W. A. Green

To those who may not be familiar with the history and organization of the Flin Flon mining property from the rime of its examination and option by the Harry Payne Whitney interests until the present start of operations by the Hudson Bay Mining and Smelting Company, Limited, this paper may give a better understanding of the property. More technical discussions are being presented to you by the men most closely connected with the various operations of the property. Location The Flin Flon mine is situated along the boundary line between the Provinces of Manitoba and Saskatchewan at approximately. 54° 45? north latitude, but largely in Manitoba. Prior to the advent of the railway, the property was quite isolated. The summer route was over a course of some 175 miles, consisting of a 125-mile boat trip from The Pas, first up the Saskatchewan river, then across Cumberland and Sturgeon lakes to Sturgeon? Landing. From Sturgeon Landing, a .16-mile portage was necessary to Camp 2 on lake Athapapaskow. From Camp 2 the route consisted of a canoe trip of 32 miles across lake Athapapaskow, up the northwest arm of Schist lake, then up Ross creek to the Company's docks, and finally a 2-mile walk to the property. The winter route was just under 100 miles in length, the difference being due to the fact that a more direct route could be followed over the frozen lakes. It went up the Saskatchewan river for a short distance above The Pas and then, leaving the river, the road followed Reeder, Rocky, and Sturgeon lakes to Sturgeon Landing, and from there over the same route as the summer one, only across the frozen lakes.

Jan 1, 1930

By M. H. Fathi

The aim of this work was to prepare the metallic coatings on 316L stainless steel dental implant and evaluate the corrosion characteristics and thus the biocompatibility of the uncoated and metallic coated dental implants and comparison of the effect of the type of coatings on biocompatibility. Three types of metallic coatings including Tantalum, Niobium, and Titanium coatings were made using physical vapor deposition process on 316L stainless steel dental implant. Structural characterization techniques including; X-ray Diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Analysis were utilized to investigate the microstructure and morphology of the coatings. Electrochemical potentiodynamic tests were performed in two types of physiological solutions at 37±1 °C in order to determine and compare the corrosion characteristics. All three types of metallic coatings had a positive effect on improvement of the corrosion behavior so that the coatings could increase the corrosion resistance of 316L stainless steel and this trend was independent to the type of physiological environment. Biocompatible metallic coatings could decrease the corrosion current density that is a distinct advantage for prevention of ion release. This can improve the biocompatibility of the implant and, consequently prevention of tissue damages, inflammation and irritation and obtained desirable histopathological response.

Jan 1, 2007

By L. E. Fischer

The background for the 630-million-dollar-plus iron ore project at Kudremukh is outlined. The system and plants for mining, crushing, concentrating, transporting via a slurry pipeline, filtering and shiploading 7.5 million metric tons of iron ore per year are fully described. The mode of operation and the problems encountered in such a transfer of North American technology to developing countries are analyzed. Difficulties encountered during construction are discussed and the progress milestones made over a two-year period are enumerated.

Jan 1, 1979

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By Albert W. Scragg

"THE ADMINISTRATION DEPARTMENT consists of six sections, all with their own supervisors, reporting to the superintendent of administration. Although each of these sections is uniquely separate, they all work together, in one department, to provide very necessary services.1. Accounting 2. Purchasing 3. Warehousing 4. Data Processing 5. Inventory Control6. Office ServicesThis department, which now numbers 108 people, had its birth in an office over a hardware store in downtown Timmins in 1964. Initially, only basic accounting and purchasing functions were performed and these, of course, were on a very small scale. The growth of the administration department is a function of the growth of the company."

Jan 1, 1974

Mine Safety in Chile ?Since the year 2000 fatality rate averages 34 per year ?1% of world mining labour force but 8% of world?s mining fatalities San Jose Mine Safety ?From 1998 to 2010 eight fatalities ?In 2003 mine inspectors recognized no second means of egress and a raise system was developed ?In 2006 182 workers were injured, 56 of them seriously ?In January 2007, there was a fatality after a rock burst, and the government ordered the mine closed ?Less than a year later the mine was back in operations. It had not complied with some of the basic safety measures ordered. One of those measures was to complete the escape way ladder.

May 1, 2011

By Donald A. Cranstone

"This paper provides a bird's eye view of the pattern of gold discoveries since 1823, the year of Canada's first gold find, up to 1983. Within this 160-year period, more gold was discovered in Canada during the last ten-year period (1973-1982) than during any previous decade. The record suggests that the potential for further major gold discoveries is high, which bodes welt f or the future of Canadian gold mining.IntroductionCanada has an impressive history as a gold producer. Since 1921 we have occupied second or third place among the world 's gold producing nations, after South Africa and most of the time the U.S.S.R. Canadian gold production over the last hundred years has added up to some 6 per cent of all-time world production.The sharp rise in the price of gold in the 1970s led to a surge of gold exploration, which in turn resulted in the discovery of significant quantities of gold in Canada. How do these recent discoveries rate in comparison with those of the more distant past? For example, are the quantities of gold in notable discoveries of recent year s, such as Hemlo and Detour, in the same league with the amounts of gold discovered around 1910 in the Porcupine and Kirkland Lake district s of Ontario? Can the combined gold content of the recent discoveries be likened to that o f the almost 40 major Canadian gold deposits, along with numerous smaller ones, discovered in Canada during the 1920s and 1930s? What are the implications of the more recent gold discovery record for future rate s of gold discovery in Canada?This paper attempts to glean answers to such questions from an overview of the period that begins in 1823, the year of Canada's first gold discovery. Gold deposits come in two major types: placer deposits and lode deposits in solid rock . Placer gold is distributed in sand and gravel. Gold in solid rock occur s mostly in gold ore filling fissures."

Jan 1, 1985

By A. R. Chambers

At the 1924 Annual Meeting of the Institute, held in Toronto, the writer presented some notes on the occurrence of salt at Malagash, Nova Scotia, together with a few remarks on the uses of salt. The development of these salt mines has attracted considerable attention to the district, and it may be of interest at this time to call attention to some of the newer uses of salt, and to give a brief account of the genesis of the Maritime salines, As it is not proposed to treat the subject in technical detail, and the paper is written in a lighter vein than is usual in contributions to your Transactions, you will please overlook any variations from a strictly technical method of presentation. The world's supply of salt is obtained in three principal ways: (1) By flooding shallow areas, or pans, with sea water, allowing the water to evaporate naturally by the heat of the sun's rays, and collecting the residue of solid salt. This method is employed, for example, at Turks Island, B.W.I. (2) By mining the rock salt in its natural state, and preparing it for market by a grinding process. This is the method adopted at Malagash, which is the only place in Canada where salt is actually mined. (3) By drilling a hole into an underground salt deposit, forcing fresh water clown the hole, and, after it has become saturated with salt, pumping the brine to the surface and recovering the salt by evaporation. This is the method pursued by the Canadian Salt Company, the Dominion Salt Company, and other producers in Ontario.

Jan 1, 1929

By Thomas. L. O.

Apart from a few sketches and incomplete maps, mainly topographical, and one or two detailed maps of placer-creeks, there is little information on the topography and geology of most of the country adjacent to the sections of the Alaska Highway in the Liard River area, particularly that part east of Kechika river. In 1943, the Geological Survey of Canada made a recon-naissance from Fort Nelson clown the river of that name to the Liard, thence up the latter to Hell Gate, and also up Beaver river for a distance of fifty miles. The whole of the area covered was found to be underlain by sedimentary rocks, not a single igneous dyke being seen. The British Columbia Department of Mines began reconnaissances near the highway both in and north of the drainage basin of Prophet and Muskwa rivers with a view to finding structures favourable for the accumulation of oil. In Liard River valley near the mouth of Smith river and at intervals from there clown to Devil' s Portage occur warm springs whose character and origin are not definitely' known, since they have not been investigated (21, p. 38A). Similar springs are said to occur at several localities over a broad belt extending from Muskwa river across the Liard to the Nahanni River country (26, p. 11). On Liard river below the mouth of Dease river, stratified sands, gravels, and clays of Pleistocene (?) age are constantly met with and in one or two places are underlain by sandy clays. The distribution of the latter, however, is very limited in the section cut by the river west of the Rocky mountains. The only range of these mountains that reaches the Liard is the high limestone ridge which approaches the mouth of Vents river from the southeast and then almost vanishes a few miles to the northwest of it (27, pp. 43-45). In general, the ranges of the Rockies in the area under consideration have been but little explored, but they are undoubtedly very largely sedimentary and, with the exception of some volcanics and intrusives on their western flanks, are probably almost entirely so. Unlike the high, deeply incised ranges in southern British Columbia, they dwindle in elevation north of Terminus mountain to low-wooded ridges separated by wide swampy valleys, and practically lose their identity between it and the Liard. The foothills, which, along the Liard, have a width of 38 miles (from near the mouth of Trout river to Hell Gate) are composed of a great series of alternating shales and sandstones, with some limestones, all folded closely together, which resemble those found in the foothills farther south (27, pp. 50, 19-20).

Jan 1, 1944

By J. Peck, F. Brackebusch, M. Scobie

"A number of alternative strategies exist to improve narrow orebody stope productivity and safety through mechanization. Particular attention is given to one of these: the development of an in-stope mining machine. This paper summarizes those characteristics of vein orebodies in Canadian mines which are considered to govern such mining machine design. It then reviews past and current attempts to develop hardrock mining machines which could potentially be applicable to narrow stope widths.IntroductionSerious interest is mounting to exploit new technology in the development of methods and machinery to stope narrow, hardrock, orebodies. The motives relate not only to the foreseen need to maintain or reduce production costs, but also to considerations of manpower availability, safety, ground control, ore recovery and dilution. This also follows the demonstrated success of technology application in larger metal orebody stoping, where machine development has been seen to lead to improved productivity as well as the future prospects of continuous mining systems and eventual automation, e.g. ITH blasthole drill development and bulk mining. This paper deals in particular with machine design for ore fragmentation in narrow, hardrock orebodies. It is considered that such machine design closely interacts with the over-all stoping method design and that both require consideration in parallel to ensure success in mechanization."

Jan 1, 1990

By Dave Thomas

?Uranium is a common trace metal at the earth?s surface, but these are amazing super-high grade (up to 25%) pods, veins and disseminated uraninite (UO2) near unconformities between Proterozoic siliciclastic red beds and metamorphic basement with graphitic metapelite and radiogenic granite. ?Pitchblende fills extensional features in reactivated fault zones and replaces matrix in sandstone ?One mining district in Canada ?the Athabasca Basin ->30 deposits /prospects -most in eastern ¼of basin -produces 1/3 of world?s U -employs northerners -VERY high tech -VERY high safety standards Unconformity-associated uranium depositsUnconformity-deposits

May 1, 2006

By G. S. Hume

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993