Search Documents

By Griffiths J. B

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gippsland Mountains, the Long Tunnel Extended Gold Mining Company produced 13,695 kg of gold, which at 1980 prices represents a value significantly in excess of $200 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subsequent occupants of the lease produced an additional 160 kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tuurriSts. To allow the visitor to obtain a better ;ri.icrstanding of Walhalla's mining past, important parts of the Long Tunnel Extended Gold Mine workings and site are being

Jan 1, 1981

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

By Sudharto RT

Sulphides of Cu, Pb, and Zn occur in quartz veins associated with a quartz monzodiorite stock at Gunung Limbung, West Java. The mineralization was polyphase and occurred at depths of less than lkm. Wall- rock alteration is extensive and typically consists of an outer zone of propylitization and an inner zone of potassic (K-feldspar- rich) alteration. Sporadic argillic altera- tion is probably of supergene origin. A variety of elements were mobilised during hydrothermal alteration and Ba in particular shows mared enrichments in the potassic zone. Fluid inclusions in the vein quartz indicate that temperatures of mineralization were within the range 250-3900C and that two fluids with differing chemistry were involved. One fluid had high Ca/Na ratios and a low overall salinity, the other had low Ca/Na ratios and a moderate salinity. The former is probably of meteoric derivation, whilst the latter had a magmatic origin. Precipitation of the sulphides was probably brought about by mixing of these fluids.

Jan 1, 1987

By Smith JW

Studies of 13C/12C ratios of carbon dioxide in seam gases and in secondary calcites show that 1. In mines prone to carbon dioxide outbursting, the source of this gas is external to the coal. 2. Faults draining reservoirs of magmatic or primary carbon dioxide, rather than intrusives, are the most likely points of entry of carbon dioxide into mines. 3. The higher the concentration of carbon dioxide in seam gas and the wetter the mine, the lower the likelihood of secondary calcite occurring as a filling in cleats, fractures etc. 4. A -role played by carbon dioxide in promoting outbursting may be the conversion of calcite to soluble bicarbonate, the removal of this in mine water and the subsequent weakening of the resistance of the bulk coal to stress.

Jan 1, 1980

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops.

Jan 1, 1992

The Central West of New South Wales is emerging as a significant metallogenic province. The development of Northparkes Mines (North Limited) and the Cadia Hill deposit (Newcrest) are establishing NSW as a highly prospective porphyry copper-gold province. Exploration in the area has been further buoyed by the Ridgeway discovery by Newcrest near Cadia. The fact that the Ridgeway prospect was discovered 300 m below surface under Tertiary basalt cover indicates that surface prospecting can no longer be considered alone as an adequate method to find significant new deposits.

Jan 1, 1997

By S Holmes

Solid Energy New Zealand operates the Stockton Opencast Coal Mine, a unique deposit consisting of high quality hard coking and thermal coals. Stockton's uniqueness includes high variability of the shipment specifications, strict quality constraints, minimal stockpiling capacity in the coal transport chain and the variability of coal quality both vertically within the seam and laterally across the deposit. The process of resource proving and modelling results in a high level of understanding of the deposit to allow detailed planning to be undertaken. The use of computer aided mine planning tools is an important component of the mine planning at Stockton. Detailed planning is implemented in the field through selective mining practices and monitoring to minimise dilution and maximise recovery of the coal resource. The quality variability in the coal, the æjust in timeÆ approach of the coal transport chain and markedly varying quality specifications from shipment to shipment requires a large coal inventory and the mine to be driven by quality constraints rather than material movement capacities.

Jan 1, 2003

Epicentres of recent shallow earthquakes in the region (3-12¦S, 126-150`E) were plotted to identify the various plate boundaries in the region, in particular the southernmost one marking the northern edge of the Australian plate. New and published fault plane solutions were examined to determine the style of faulting and state of stress along the Australian plate boundary. From east to west the boundary is first a subduction zone along the Solomon Islands, then a spreading centre across the Solomon Sea, a zone of compression and left lateral strike slip along the Papua Peninsula, almost pure thrusting across the centre of New Guinea and lastly left lateral strike silo through Irian Taya to the outer Banda Arc. The principal stress is very consistent, trending NW to NNW in a near horizontal plane, from the triple junction of the Pacific, Solomon Sea and Australian plates in the east to the Banda Sea in the west. Only along southern Solomon Sea plate margin which is a divergent boundary, is the stress different in type and direction.

Jan 1, 1987

The overall mineral assemblage of the Broken Hill orebody is similar to that of a skarn. However unlike the classical skarns it does not represent contact metamorphism of pre-existing limestone beds. It is a stratiform accumulation of exhalative-sedimentary silica, sulphides, (Ca, Fe, Mn) silicates and carbonates, fluoride and phosphate that has later undergone regional metamorphism. The resulting development of coarse-grained quartz, sphalerite, galena, rhodonite, bustamite, mixed carbonates, fluorite, apatite and many minor phases has produced a sulphide-rich skarn- like mass that like many others of its kind, might best be referred to as a stratiform skarn. Recent investigations of occurrences of this type are showing that the incidence of concentrations of particular metamorphic minerals in and adjacent to such orebodies are closely related to bedding and to former sedimentary facies patterns. From this it appears that the mineral assemblages may be used to deduce not only the nature of the materials laid down in the beds, but also the physico-chemical conditions under which sedimentation took place. Several stratiform deposits, including Broken Hill, are used as examples to show that variations in these conditions may have a profound influence on the subsequent response of the rock to regional metamorphism and hence on the mineral assemblages that finally develop.

Jan 1, 1983

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

By Shining Z

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores, as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Spencer PA, Winborne DA

The Porgera mineral deposit in Papua-New Guinea contains gold as finely divided, probably submicroscopic (1 um) particles dispersed in a pyrite sulphide matrix. Only 25-30% of the gold in pyrite can be extracted by direct cyanide leaching and fine grinding the pyrite does not increase gold extraction significantly. This work is concerned with the application of alkaline leaching at atmospheric pressure to oxidise the pyrite prior to gold recovery by cyanidation. The paper presents and discusses results of a comprehensive set of testwork using sodium carbonate, sodium hydroxide and calcium hydroxide alkaline media. Best results, at 60-70% gold extraction, were obtained with sodium hydroxide systems.

Jan 1, 1984

By D R. Swinbourne, Y H. Yang

Calcium ferrite slag has gained prominence in the copper smelting industry over the last decade due to the emergence of continuous converting as an established technology. As smelters move towards processing which is higher in intensity, more efficient and more environmentally acceptable, its use is likely to increase because it has technical advantages over conventional iron silicate slag, which include a higher magnetite-holding capacity, lower copper losses to slag and a lower viscosity. Calcium ferrite is currently the converting slag of choice in the Mitsubishi process at operations in Japan, South Korea, Indonesia, Canada and Australia, and in the Kennecott/Outokumpu flash converting process in USA. However, users of this slag have experienced problems in containment due to its highly corrosive nature and low viscosity. As use of this slag becomes more widespread the containment problem will assume greater importance. Consequently, work has recently been carried out to establish the mechanism of refractory attack and devise means to retard it. This work will be critically reviewed in this paper.

Jan 1, 2000

By Swanson AR, Nicol SK

A study has been made into the influence of feed size distribution on the flotation response of coal. The results show that a full description of the flotation response of a coal must not only consider the inherent floatability of the coal, but also, the size distribution of the feed to flotation. The performances of a number of flotation circuits were compared using a coal which was "poorly floating" because of its size distribution. Split feed flotation, two stage reagent addition, and reflotation of classified tailings all gave better yields than that obtained by conventional single stage flotation. The optimum flotation circuit for the washing of the coal in question, was reflotation of classified tailings.

Jan 1, 1978

The Australian underground contract mining industry has grown from almost nothing 25 years ago to the point today where half the countryÆs underground mines are using contractors to produce their ore and do their development. This growth was driven by the need to change poor industrial relations and work practices in sectors of the industry, along with the needs of many small gold mine owners to preserve their capital by using contractors to do their mining. The industry is dominated by two major privately owned contractors with a number of other publicly and privately owned contractors making up the balance of the market. This paper discusses the important trends in the contract mining industry and the directions it may take in the next few years.

Jan 1, 2005

BHP World Minerals (BHP) commenced development of the Cannington exploration decline in 1993 using Peabody Resources LimitedÆs Mining Services Division (PRL) as the contractor. Approval was given in 1996 to complete the mine development and bring the mine into production in 1997. The total mine development at Cannington by PRL has included 14 km of headings, 1040 m of shaft sinking for ventilation and ore hoisting and 990 m of raise boring for ore passes and vent rises. Hard money schedule of rates contracts were used for mine development from 1993 until early-1997. This took the mine development down to 570 m below the surface and developed six levels. Because of significant risks, the final phase of the mine development was completed in 1997 under a partnering agreement. This paper examines the factors considered in making the change to partnering, the issues involved in negotiating the partnering agreement to complete the Cannington mine development and the outcomes of the agreement.

Jan 1, 1998

By Chilman G. F, Lean P. J

The New Broken Hill Oonsolidated LImited (NBHC) concentrator was commissioned in 1952 and underwent a number of expansions over the next 25 years. In 1978, the decision was taken to expand further from 1.20 million tonne/yr to 1.43 million tonne/yr. This increase necessitated a substantial modification to an already over-taxed grinding circuit. The circuit consisted of rod mills, ball mills and rake classifiers. Plant data of grinding mill performance was obtained to develop mathematical models of individual units that could be combined to simulate total circuit performance in a number of configurations. The data provided further illustration of the validity of the perfect mixing model for relatively small increments of ball mill scale-up.

Jan 1, 1983

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990