Search Documents

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

By Phillips H. R

The action of free rolling disc cutters is well understood, relationships between disc geometry and performance having been established both in the laboratory and under field conditions. However, under severe operational conditions a malfunction of the disc bearing assembly is likely to produce a definite change of cutting action. Collapsed or siezed bearings can even prevent the disc from rolling and thereby create what is equivalent to a drag pick. This paper describes a programme of laboratory experiments using deliberately stalled discs. Their performance under such conditions is contrasted with that for a free rolling disc and also with a drag pick having a ridged front developing into a negative radiused back clearance angle. In conclusion an assessment is made of the influence stalled discs can have on the torque and thrust requirements for a tunnel boring machine.

Jan 1, 1981

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

This paper summarises the performance of the gold exploration industry in the Western World since 1970, with particular emphasis on the period 1985 - 2003. It identifies the number and size of major (ie >1 million ounce) primary gold discoveries made over this period by location and type of company. Estimates are also made of the likely contribution from smaller discoveries down to 0.1 million ounces. It also assesses the overall trend in the percentage of grassroot discoveries that are converted into mines, and the time taken to get them into production. By comparing the discovery data against total exploration expenditures it is possible to determine the average unit cost of finding a major gold deposit. It is significant to note that the average unit cost per discovery and per ounce of resource has tripled over the last 30 years. An attempt is made to determine the overall economic value generated by the industry. This is based on a detailed analysis of the rates of return and the Net Present Values (NPVs) of 109 major gold projects. After including an adjustment for discoveries not modelled, the NPVs are compared against the total amount of money spent on exploration to determine the value-to-cost ratio for the industry. Based on historical spot gold prices and tax rules, it is found that the return on investment for gold exploration in the Western World over the period 1985 - 2003 was around five per cent real after-tax. The returns achieved in the US and Australia was significantly higher than that for Canada. The returns also appear to have declined in recent years. With regard to the relative performance of junior versus major companies, the paper estimates that the junior sector accounted for 30 - 40 per cent of the total exploration expenditure, and were was associated with 34 per cent of the total number of major deposits, 27 per cent of the contained ounces and 25 per cent of the economic value found.

Jan 1, 2004

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022

By D Stow, M Edmondson

Lemington coal mine is operating in an environmentally sensitive area in the Hunter Valley, NSW, Australia. Late in 1999 the southern pit was developed using a series of box cut blasts. After the initial development the area would have been free dug due to the soft, well-jointed nature of the deposit. However, it was decided to trial drill and blast to determine if shovel productivity could be improved to enable an overall mining cost reduction. The initial trial blast results were less than satisfactory with both environmental issues occurring and the desired shovel productivity not being achieved. An audit of the blasts indicated that wet ground and the presence of soft clay inter-bedded with harder rock caused the poor blast results. Also, water-affected explosive product combined with explosive energy loss into soft ground led to flat spots and tight digging in the hard band areas, resulting in the lower dig rates. Lemington Mine and Orica Explosives developed a plan to match the rock with the appropriate explosive type and energy. This resulted in a number of blasts over a six-month period using a new non fuming explosive product, æNovaliteÆ. The results have been excellent with the environmental issues being totally resolved and dig rates improved, enabling reductions in mining costs. This has allowed the mine to continue with their exemplary record of environmental management whilst achieving operational efficiencies.

Jan 1, 2001

Universities have had a long history in the education of geology graduates, Analysis of this history reveals a record of success, as judged on a world basis. However there have been significant changes in the last 20 years that have impacted on the ability of universities to continue to provide their traditional style of geology education. These changes have increased in the last 10 years. In the teaching side, there has been a change in expectations. Additionally the increasing workload decreases the value of each academic to perform the tasks needed by the new education. In the area of research, the funds provided have continued to decline, in both real and absolute terms, and it is now necessary for universities to seek out funds to pay for their postgraduate research. Additionally, the universities have slipped into the error of what cahn only be termed "academic incest", and research student mobility has decreased to an undesirable level, stifling initiative and new ideas in a number of cases, The only solution is for Government monies to be "directed" - ie that the postgraduate student must leave his or her original university in order to receifve the research stipend/scholarship. On the government front, the government and its agencies have not adequately analysed and recognised the need for the redirection of education and research funds into the needy areas of science and technology, especially those that related to the minerals area.

Jan 1, 1986

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

By Iley J. D

The production of zinc from low grade concentrates, particularly those high in iron, has a poor economic return due to a combination of higher concentrate transport costs, increased processing costs and an increased cost for disposal of iron residues. The production of iron-bearing residues from the electrolytic zinc process is also seen as undesirable for both cost and environmental reasons. This paper details the pilot plant testwork conducted at the Pasminco Research Centre in conjunction with Minproc for the production of zinc oxide fume from a high-iron zinc sulphide concentrate from Colquiri in Bolivia. The concentrate is derived from a tailings retreatment operation and has a high iron content (40 - 45 per cent Zn, 14 - 17 per cent Fe) due to the presence of marmatite. Pilot plant trials were conducted using the slag bath reactor at Pasminco Research Centre at rates up to 500 kg/h of pelletised zinc concentrate, using a natural gas/oxygen-enriched air lance. The fume produced averaged 76 per cent Zn at recoveries up to 96 per cent and was recovered in a baghouse after gas cooling. The iron was oxidised into a fayalitic slag that passed the TCLP test (toxicity characteristic leaching procedure) and the sulphur was oxidised to produce a high SO2 gas which would be suitable for sulphuric acid production. The process produces a zinc oxide fume that can replace calcine as a feed for electrolytic zinc plants. The iron reports to a stable slag for disposal, thus eliminating the need for its disposal as jarosite from the leach plant. Only a simple leaching operation on the fume is required as there is no zinc ferrite present.

Jan 1, 1993

The Porphyry Gold Mine (150km NE of Kalgoorlie) was reopened in November 1983 with production commencing in April 1984. Original reserves quoted for the open pit were 822000 tonnes at 5.2 g/t Au based on wide spaced diamond drill holes. Close spaced grade control drilling has revealed some loss of tonnage and a significantly lower grade. In the area of the pit mined to 30 June 1985 this grade control reserve estimate contained 67% of the gold in the original ore reserve with the grade being 19% lower. It is anticipated that the final grade control reserve estimate will contain around 80-85% of the gold contained in the original reserve. There has been close agreement between the Mill Head grade (4.19 g/t Au) and the grade control predicted grade (4.2 g/t Au) confirming that dilution is not a major problem. After initial poor agreement (attributed to "lock-up" in the circuit) the bullion calculated head grade steadied out at 93% of the grade control prediction. This difference is considered to represent the geostatistical bias in the drill hole/crushed rock sampling. Gold recovery has been in the range 93-95% (compared with bullion calculated grade). The net result is that the recovered grade of ore mined to 30 June 1985 is 70% of the original ore reserve grade.

Jan 1, 1986

By Leahy GJ, Wright DJ, Player RI

The operation of a one tonne submerged combustion pilot plant for the recovery of copper from anode furnace and converter slags is described and the effects of variables discussed. Using coal as reductant, copper levels of anode furnace slag were lowered to 1% or less, with batch times of approximately 120 minutes. Fluxing with limestone was required to produce a fluid slag at temperatures of 1200 - 1300¦C. For converter slags, reduction to 0.5% Cu or less was achieved in batch times of 35 minutes. The chemistry of the pyrometallurg- ical recovery of copper is briefly reviewed in relation.to copper recovery methods.

Jan 1, 1978

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

A formalised approach to risk management has been regulated in the United Kingdom (UK) since the Construction (Design and Management) Regulations 1994 (CDM) came into force in 1995. These regulations have recently been revised in 2007. In response to a series of significant claims around the world the UK insurance industry published a code of practice for risk management of tunnels in 2003, and that was followed by an international version in 2006. Probably one of the main contributions of this new approach is the recognition that health and safety risks can best be addressed early in the process, initially by the owner and then by the designers. One of the aims is to achieve elimination of risks by good design. The advantage of a risk-based approach to tunnel design is that all risks are considered explicitly, and any residual risks in the design are communicated clearly to the construction team. This paper looks at the implementation of this formalised approach to risk management with reference to the A3 Hindhead Project. The design has been undertaken in accordance with the requirements of the CDM regulations, and also in compliance with the Joint Code of Practice for Risk Management of Tunnel Works in the UK. An outline of the risk-based design process used is provided, including examples.

Jan 1, 2008

By Lyman G. J, Ka

The use of images to determine blast fragmentation is the only feasible technique when one does not want to disturb the production cycle. However, three major problems exist with the use of images. The first is determining real size from a two-dimensional particle, the second is estimating the fines which are missing due to image resolution and particle size range, and the third is proper sampling such that a statistical probability can be calculated for the distribution. Once these problems are resolved, the tedious process of digitizing images by hand may be automated. This paper describes the present techniques used at the JKMRC to "size" blast fragmentation, estimate the missing fines using the Rosin-Rammler equation, determine the sampling error using Gy's sampling equations, and extract the particles from an image using an IBM-AT computer.

Jan 1, 1990

This paper describes the operation involved in the sinking of a concrete-lined elliptical-shaped shaft at North Broken Hill Limited.Major factors such as geological features, future ventilation, ore haulage at depth and their relation to the location and selection of the type of shaft are described.Features covered in the sinking of the shaft include equipment details, with special reference to mechanical mucking, operational cycles based on time study analyses for sinking, concreting and the placing of steel sets. Safety precaution and statistical data is alsoincluded.INTRODUCTIONDue to the northerly pitch of the ore bodies in North Broken Hill Limited leases at approximately 42°, and the deepening of the active mining zone, it became apparent that No. 2 Shaft, the main operating shaft, would become unsuitable for the extraction of ore from the lower levels.Another major problem was the ventilation of the lower levels, and it was evident, that to ventilate efficiently these, and deeper levels, another upcast ventilation system would be required.Consideration was given therefore to the following: 1. Sink No. 2 Shaft from the existing bottom at 2770 ft. to 4200 ft., or Sink an internal shaft from the 2600 ft. level approximately 1000 ft. N. of No. 2 Shaft.2. Sink a new haulage and downcast shaft from the surface.3. Sink a new upcast ventilation shaft from the surface.It had been suspected that the ore bodies might flatten or even undergo a pitch reversal before reaching the...

Jan 1, 1956

By Williams JK, Bolitho BC

Laverton Gold NL (Laverton) is the first junior Australian mining company to establish a viable mining operation in Indonesia. It successfully commissioned the Rawas plant in Sumatra this year with an average anticipated production of 85 000 ounces of gold equivalent (as gold and silver) per year, a feat of which Laverton is justifiably proud.Working in Indonesia and South-East Asia generally is very stressful for juniors and stretches human and financial resources to the limit - more so than in medium to large companies which can absorb the workload in-house more effectively.

Jan 1, 1997

Geological models for the exploration and evaluation of epithermal Au and porphyry Cu-Au deposits rely upon a classification of different deposit styles and an understanding of the evolutionary processes of deposit formation. These models guide the interpretation of subsurface deposit anatomy in order to target drill testing and assist the explorationist to focus on the more prospective projects. It is important for the explorationist to distinguish between different styles of magmatic arc Au deposits as each style displays distinctive characteristics with exploration implications. Magmatic arc Au deposits are distinguished as porphyry Cu-Au formed at depths of 1 - 2 km at the apophysis to larger, buried, magmatic sources which are also the ultimate metal sources for the varying styles of shallower level epithermal Au deposits. Low sulfidation epithermal Au deposits characteristically develop from dilute circulating meteoric waters and are distinguished as the group with a closer relationship to intrusive source rocks, and slightly higher sulfide contents (still generally

Jan 1, 2004

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986