Search Documents

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

A Master of Applied Science degree course in Mining Geomechanics commenced in 1983 at The University of New South Wales, taught by extern- al (correspondence) studies. The course is aimed at graduates employed in the mining indust- ry, and especially people involved in geomechan- ics projects on a routine basis in remote locations. This kind of course is unique in Australia and is one of only two correspondence programmes available at this University. The author designed the course and nursed it through the early years, and was Director until 1986. The paper describes the teaching and assess- ment methods and also discusses aspects of admin- istration and coordination of such a course. It is concluded that an important need of the mining industry is being catered for and it appears that similar correspondence course for- mats would also be useful in other areas of the minerals industry.

Jan 1, 1986

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

By C X. Zhang, W K. Ru, S C. Hu

To study the creep properties and the energy evolution characteristics of the weakly cemented rock (WCR) in western China, the creep deformation damage law of weakly cemented mudstone (WCM) under graded loading and the energy evolution characteristics of each creep stage were analysed based on the triaxial graded loading creep test of WCR. The results showed that as the confining pressure increased, the creep failure strength of the WCM increased from 9.5 to 24.8 MPa, and the relative displacement of the mineral particles in the mudstone increased gradually, resulting in a reduction in the fracture angle from 79.7° to 58.3°. At the same stress level, the strain energy Ue, the total energy U, and the dissipation energy Ud all increased as the confining pressure increased, but the growth rates of U and Ud decreased gradually, while the growth rate of Ue remained high. At the end of the stable creep stage, Ue increased slowly with the confining pressure, while U and Ud increased rapidly with the confining pressure, and their growth rates were basically the same. At the end of the accelerated creep stage, the growth trends of these three energies were all positively correlated with the confining pressure, Ue was significantly lower than that at the end of the stable creep stage, and Ud and U were further increased. These results revealed the unique creep properties and energy evolution characteristics of the WCR, providing a theoretical basis for long-term stability control of roadways that are built with WCR.

Nov 29, 2022

By S Prakash, P S. R Reddy, S K. Biswal, V N

The beneficiation potentials of two Indian iron ore slime samples by flotation technique using both cationic and anionic collectors are investigated. The direct and reverse flotation of slimes using oleic acid and dodecylamine as the collector have been studied using both conventional cell and flotation column to upgrade the iron content. The characterisation studies of iron ore slimes indicated that the samples are extremely fine in nature and contain substantial amounts of martite, magnetite, goethite, limonite, kaolinite and quartz beside hematite as the dominant iron mineral phase. The samples on average contain around 52 - 58 per cent Fe, four to seven per cent SiO2 and five to six per cent Al2O3. Taking into account the physico-chemical properties of the slimes, it is attributed that both the samples need to be deslimed by hydrocyclone before flotation. The results of both cell and column studies on sample I showed that a feed containing 57.5 per cent Fe could be upgraded to 65.5 per cent Fe at 50 per cent overall recovery with simultaneous decrease in SiO2 and Al2O3 content to 2.3 per cent and 1.8 per cent respectively by using oleic acid as the collector. In the case of sample II, it has been established that reverse flotation of silica is the better technique to improve both the grade and recovery of iron. Batch flotation studies in cell indicated that a product with 63.1 per cent Fe could be obtained at 40.0 per cent yield with 63.6 per cent iron recovery by the combination of reagents such as gum acacia, sodium hexa meta phosphate and dodecylamine. The performance of column flotation techniques is far superior to that of the cell with respect to both grade and recovery. The concentrates are found to be quite suitable for commercial exploitation as pellet feed.

Jan 1, 2005

This paper has been prepared to challenge the thinking of new leaders entering the mining industry in two areas. First, what is the worldÆs perception of mining and what does this mean to those entering the industry? Second, what is the future of learning in the mining industry and how can the industry attract and retain the best people?Then in closing, how can mining companies turn these challenges into opportunities and specifically how is BHP Billiton meeting these challenges.

Jan 1, 2004

By Khosrowshahi S

The objectives of grade control remain unchanged but new methods are being developed to attain them. Since the early-1990s, an improvement in the power of mine site computers has made the geostatistical tools of conditional simulation more accessible. Optimisation of the grade control process on mine sites now involves two stages: optimisation of the sampling regime and optimisation of the interpretation of ore and waste boundaries. Optimisation of the sampling regime first requires an understanding of the nature of the mineralisation and in particular the impact of particle size on the sampling precision. This relationship, termed the Fundamental Error of sampling, enables an optimum subsampling protocol to be defined for the sample preparation and assaying. However, the actual sample collection method, whether drilling or trenching, must be correctly selected and the sampling grid should be optimised. The relative costs and benefits of various alternative sampling methods and grids can be determined using the method discussed. The use of the grade control data can also be optimised. In the past ore and waste boundaries were often defined using a linear interpolation algorithm that smoothed the data (such as polygonal, sectional, inverse distance squared or even kriging methods). Frequently the relative impact of ore loss and dilution could not be estimated. Conditional simulation to generate equiprobable alternative maps (realisations) can now be adopted to address these issues. A transfer function is then used to evaluate the similarities and differences between the maps. The Ore Block Optimisation (OBO¬) process is a transfer function that produces a three-dimensional model of the optimal ore block outlines. This provides a clear guide for the mining geologist to refine and mine. The nature of the transfer function and the inputs and outputs are discussed. In the past, reconciliation has been the `acid test' for any grade control system. Any ore blocking method based on conditional simulation can make use of the exhaustive data set to ensure that reconciliation between prediction and production will improve significantly. The OBO¬ method provides a guide to the mining geologist to ensure that the best ore blocks are mined. Misclassification between ore and waste is reduced, ore loss and dilution are minimised (and are measurable) and ore is optimally assigned to stockpiles of various cut-off grades. These advantages significantly enhance mine profitability and control of the mined grade.

Jan 1, 1997

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

By Cusack BL

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. This resulted in a deterioration in metallurgical performance with increased loss of lead and zinc to residues at each concentrator. Investigations to determine the cause of the problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical Deterioration.

Jan 1, 1970

By Heyes GW, Orrock GI

The fine grained complex orebody at Elura contains galena, silver and sphalerite in a matrix which is mostly pyrite; sulphides account for about 90% of the orebody. A differential flotation circuit is operated to con- centrate lead and silver in the first section and zinc in the second. The metallurgical performance to date indicates the need for improvement. The lead section has been sampled in detail to comprehensively assess its overall performance and to define problems associated with lead and silver flotation. The substantial amount of pyrite in the feed dominated the perfor- mance of each stage of the separation. It was responsible for extensive dilution of all concentrates and, as a consequence, for very large circulating loads. The rougher concentrate contained 68% pyrite some of which was rejected through the three stages of cleaning to 39% in the final concen- trate. However, this was still sufficient to hold the assay of this product below 45% Pb. Size by size behaviour shows that flotation rates of the valuable minerals, as characterised by their rate coefficients, were low through- out the circuit. There was a significant deterioration in these rates between rougher and cleaner I stages which resulted in large circulating loads between these stages. There was practically no recovery of coarse valu- able minerals to the final concentrate. The dilution of the final concen- trate by non-sulphide gangue was not a major problem. If the recovery of the galena and silver in the +38¦m size range could be raised to that of the - 381Lm size range, galena recovery would rise from 78% to 86% and silver recovery would improve from 46% to 59%. The Pb grade of the final concentrate would remain the same.

Jan 1, 1988

By J D. Tolley

The shift towards clean energy technologies is having a significant impact on the mining industry, with the demand for minerals such as copper, nickel, cobalt, lithium, manganese, and graphite increasing exponentially. To meet the goals of the Paris Agreement, mineral requirements for clean energy technologies would need to quadruple by 2040, and to achieve net-zero globally by 2050, mineral inputs in 2040 would need to be six times more than today. The most significant driver of mineral demand is electric vehicles (EVs) and battery storage, with lithium seeing the fastest growth, and copper demand doubling over the same period due to the expansion of electricity networks globally. The demand for these minerals is expected to rise significantly as investments in clean energy technologies continue to grow in the future. As the world moves towards a decarbonised economy, the minerals industry is under increasing pressure to reduce its environmental and social impacts and meet the increased demand for minerals. Mining companies are facing additional challenges due to the depletion of near-surface mineral deposits globally, with more mines transitioning from open pits to underground. The transition to underground mining requires the right strategy to economically access deeper mineable inventories and to keep up with future clean energy technology demands to achieve net-zero globally by 2050. One key way to achieve this is through decarbonisation using ‘green’ mining technologies such as replacing current primary diesel mining fleets with battery electric vehicles (BEVs). However, these measures through electrification overlook the bigger opportunity to maximise the socio-economic returns from the mine while also reducing the overall carbon footprint. Corporate cut-off grade policy is one of the most significant influencers on the total environmental and social impacts of the mining industry. The purpose of a corporate cut-off grade policy is to implement strategies aligned with achieving all the mining companies’ corporate goals, with decarbonisation targets becoming a primary driver for mining companies. Table 1 shows the evolution of cut-off theory with the increasing number of dimensions and driving inputs per iteration.

Aug 2, 2023

THE following notes simply sum up the writer's experience, which extended over a very busy period of some three years, dealing with wolfram ores and concentrates. The three methods for the estimation of tungsten that are discussed below are well known, but these results of their trials and comparison under technical conditions may be interesting. Method I. The routine procedure for the assay of rich wolfram ores or concentrates was as follows: Take 1 gram of finely-ground sample; digest with HCl and HNOs for about 2 hours, evaporating down to near dryness. To the remaining 5 cc., say, of liquid, add water, warm or boil for 1 to 1.5 hour, filter through a small filter paper, and wash the beaker and the insoluble matter with hot dilute HCl. It is best to keep the bulk of the insoluble matter (WOs, Si02, etc.) in the beaker at this stage. Then plaee a weighed porcelain dish under the filter funnel and wash the beaker and the filter paper with successive small quantities of strong NHOH, finally bringing all the insoluble matter on to the filter paper, and collecting the ammoniacal filtrates in the porcelain dish (S). Then place the filter paper with the insoluble matter in a porcelain crucible, dry and burn off the paper, cool, and brush the contents of the crucible on to an agate mortar, grind it to flour, and brush this back to the original beaker without loss. In the absence of draughts this can be done safely. Re-treat this residue with' acid and ammonia as above, running the second ammoniacal filtrate into the previous porcelain dish, which in the meantime has been heating on a water-bath.Finally evaporate to dryness on the water-bath the combined ammoniaeal filtrate, and then heat gradually to a red heat over a Bunsen burner, cool, and weigh. Then the contents of the porcelain dish give the WOs (tungstie aeid) direcvly (5).The final filter paper and insoluble matter may be ignited in a porcelain crucible, thus giving the "insoluble matter." If the ore...

Jan 1, 1922

Tokyo Metropolitan Government designs the stormwater storage plans in underground, as a measure of flood control in completed urban district and improvement of combined sewarage system. This time, introducing those plans, we report about IKEJIRI and SIN-KOMAZAWA STORAGE TRUNK LINEs design and construction. They are located in Meguro river basin of the Morigasaki drainage area. Both storage trunk lines have capacity to store 15O,000m3 of stormwater. They are in use for countermeasure of flood till Meguro river's strengthening (intensity 50 mm/h) is ended. And after the strengthening, they will be in use for improvement of river water quality, through the storage of combined sewage and first runoff, which, otherwise overflows weirs and flows to river in a rainy day. These storage trunk line's full length is about 5700m. Boring diameter 66140 mm (f = 2672m) and 47800 mm (I = 2866m) of these tunnels are constructed by Mechanical Shield tunnelling method. And boring diameter 3600 mm x 4000 mm (R = 180m) is constructed by NATM tunnelling method. We began works in 1983, and have a mind to complete in 1987.

Jan 1, 1987

By Martin R. E

L44 Shaft is a major upcast ventilation shalt in the hanging wall of the 1100 Orebody. Various techniques for stripping a raisebored pilot hole were combined to produce L44 shaft. From the surface to 198 m depth, the shaft was concrete lined 7.3 m internal diameter. Below this the shaft was developed to 7.6 m diameter unlined. 11 level, 540 m below the surface, was the first readily accessible level connection. The section to 198 m depth was benched and concrete lined through weak oxidised ground. When more competent ground was encountered the operation was converted to horadiam stripping. This application of the raiseborer has led to a safer, more efficient method of shaft development.

Jan 1, 1977

The Circum-Pacific area is one of the most important gigantic skarn-metallogenic belts in the world. In more than 20 coastwise countries of this region, there exist thousands skarn deposits of different types. According to the differences of major metallic elements, the skarn deposits may be classified into seven subtypes, i.e. Fe, Cu, Pb-Zn, W, Sn, Mo and Au skarn deposits. In this paper, the distribution. and geological characteristics of above-mentioned types of skarn deposits are described briefly. Skarn deposits may also be classified on the basis of the dominant calc(magnesian)-silicate mineral assemblages into four types: magnesian, calcic, manganoan, and alkaline skarn types. Magnesian skarns may be associated with Fe, Cu, Au,, Sn, B, Be mineralization, calcic skarns with Fe, Cu, W, Mo, An, Be, Pb, Zn, Sn minerailization, while the alkaline skarns occur in U(Th, Nb) deposits. The skarn deposits of both East and West Pacific rims have many general characters, but have some diferences in geotectonic settings, intensities of mineralization, distribution, and metallogenic epoches. In this paper, the minerogenetic series and the mineralizing specialities of related magmatic rocks of the skarn deposits are also discussed.

Jan 1, 1990

By Booth GW, Robertson IG

The Paddington Gold Mine ties within the Norseman-Wiluna greenstone belt, in the celebrated Eastern Goldfields province of the Yilgarn Block, Western Australia. Regionally, tropical to subtropical weathering has effected development of a prominent regolith and a deep lateritic profile. Detailed examination of the clay mineralogy, largely from a single drill hole which traversed the original Paddington I deposit, outlined three separate, vertically gradational assemblages, which are, in part, rock-type dependant. These include; 1. kaolinite with minur to trace quantities of sericite/illite (0-22m), 2. smectite and/or interstratified clay minerals, together with variable amounts of kaolinite, relic chlorite and illite/sericite (22-81m), and 3. chlorite and sericite (> 81m). Near surface, kaolinitic assemblages may be directly correlated with the intensity of lateritization, whereas smectite and interstratified clays from intermediate zones appear in association

Jan 1, 1989

Rio Tinto Iron Ore is currently working towards finalising comprehensive Native Title land access agreements, which cover all of the current eleven mines and infrastructure owned and operated by the company in Western Australia's Pilbara region. Critically, the agreements represent a mutual commitment to a long-term relationship and address many areas of concern by promoting indigenous enterprise, well-being and regional development opportunities. Our objectives in the process are to obtain the informed consent of the traditional owners for our Pilbara expansions while providing benefits to them in a way which provides lasting and substantial improvements to health, education, housing and real jobs in the mainstream economy.   To facilitate the agreement negotiations, Rio Tinto Iron Ore (RTIO) proceeded in 2005 to research and design a specific strategy around Aboriginal relations and local community engagement in the Pilbara. Wherever we operate, Rio Tinto follows a fairly simple formula in working with communities, which is comprehensively aligned to local context.   This presentation provides an overview of Rio Tinto Iron Ore's community engagement strategy in Western Australia's Pilbara region. It will also explore the establishment of regional standards on employment, business development and contracting that have been developed to ensure Indigenous people are engaged in the development of their region and are able to contribute to supporting the growth and development of mining in the area with the expectation that there is prosperity for all. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

The paper discusses how automation is steadily proceeding throughout all areas of the electrolytic zinc industry. Fluid bed roasters with integral sulphuric acid plants are now on -computer control. Highly efficient, continuous leaching and purification stages, with feed-forward predictive and optimisation computer control, precede electrolytic cells with on-stream solution analysers and automatic stripping of deposited zinc. Controlled electric induction furnaces feed continuous casting lines, equipped with automatic stacking and strapping, machines, after computer based metal analysis has confirmed metal purity or alloy composition. The paper also discusses the use of computer models tied to process control systems, and the equipment and solution measurements that could be automated with advantage, using modern micro-based controllers and analysers.

Jan 1, 1985

By H Durrant, P I. Corke, J Cunningham

This paper reviews the state-of-the-art in the automation of underground mining vehicles and reports on the development of an autonomous navigation system under development through the CMTE with sponsorship arranged by AMIRA. Past attempts at automating LHDs and haul trucks are described and their particular strengths and weaknesses are discussed. The auto-guidance system being developed overcomes some of the limitations of state-of-the-art prototype æcommercialÆ systems. It can be retrofitted to existing remote controlled vehicles, uses minimum installed infrastructure and is flexible enough for rapid relocation to alternate routes. The navigation techniques use data fusion of two separate sets of sensors combining natural feature recognition, nodal maps and inertial navigation techniques. Collision detection is incorporated and people and other traffic are excluded from the tramming area. This paper describes the work being done by the group with regard to auto-tramming and also outlines the future goals.

Jan 1, 1998

By K Zhao, H Gong, B Li

Health and safety are the first priority for Australian minerals sector. Australia has a global reputation in the mining industry. However, accidents occur every year. Legislation and regulation are important to prevent the accident from occurring, so do the new technologies. It is sad to witness the collision incident persisting and the long called collision avoidance system (CAS) is still not widely used in underground mines. The main reason is that the existing systems are still not advanced enough. The current CASs utilise GPS, infrared, ultrasonic, RFID, Radar, electromagnetic etc have their limitations and disadvantages. For instance, GPS is widely used in a surface mine, but it cannot be applied in underground mine; Infrared and electromagnetic have the false positive problem.

Sep 1, 2024