Search Documents

An exploration and preliminary mine design contract was undertaken in Thailand to establish whether adequate lignite resources existed for the addition of future power generation plant through to the year 2000. The lignite ranges in heat value from 14 to 24 MJ/Kg (air dry basis) and occurs in 2 major seams consistituting measured reserves of 536 Mt (with an ash cut-off level of 45 % on an air dry basis) and a strip ratio of 4.1 bank cm/t. The paper describes the pre-planning, programming, equipment used, project management, logistics and exploration methods adopted to undertake the contract in a monsoonal area using Australian drilling and geophysical contractors.

Jan 1, 1983

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

By P G. Bourke, A Yáñez, G J. Jameson, N M. L Kupka

The kinetics of fine and ultrafine particles in conventional mechanical flotation cells are limited (Feng and Aldrich, 1999; Trahar, 1981; Wang et al, 2016). Accordingly, even limited recoveries with such machines require long residence times. Theoretical investigations into the rate of capture of fine particles by flotation, have indicated that a key parameter is the rate of shear in the fluid surrounding the bubbles and the particles. Achieving fast flotation rates of ultrafines requires a new method of bringing the particles and bubbles into contact, utilising the beneficial properties of highly dissipative flows to break through the water boundary layer. In 2010, a new type of flotation cell known as the Concorde Cell was described, in which bubbles and particles are brought together in a sonic shock wave (Jameson, 2010). Earlier research had shown that when a dispersion of fine bubbles in liquid passed through a converging nozzle at the local speed of sound, the resulting shock wave downstream generates a mass of even finer bubbles in the flow as it passes through the shock wave. The fluid within the shock wave is highly turbulent, and an environment is created that is very favourable to particle-bubble collision and capture. In this paper, we briefly describe the Concorde Flotation Cell and give examples of its use.

Aug 24, 2022

By Wilkinson LR

The object of this paper is to present a brief overview of applications of radioisotopes in mineral processing. The emphasis is towards on-line applications, and is to present the broad picture rather than become involved in the details of particular applications. For a more detailed and comprehensive coverage, the reader is referred to the International Atomic Energy Agency International Symposium on Nuclear Techniques in Exploration, Extraction and Pro- cessing of Mineral Resources, held in Vienna 7-11 March, 1977. Because of space limitations here, we have inmost cases restricted coverage to those applications of radioisotopes within the direct experience of Amdel and Australian research bodies. Radioisotopes spontaneously emit energy in tiie Form of a and S particles, and electromag- netic radiation. The electromagnetic radiation is generally referred to as y-radiation when it originates from the nucleus, and X-radiation when originating from the electrons orbiting the nucleus. X-ray and y-ray energies overlap, with X-rays extending from a few electron volts (%') up to about 100 keV. Gamma rays in the useful energy range extend from a few keV up to .feV.

Jan 1, 1978

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

The Coal Corporation of New Zealand Ltd (CoalCorp) is the largest coal producer in New Zealand, with extensive properties in both the North and South Islands. CoalCorp's North Island operations are kilcmetres to the south of Auckland. opencasts, are located in the catchment wildlife, historical and scenic values. in this catchment is the single most mining operations. centred on Huntly, a town some 80 Five coal mines, four of which are of Lake Waahi, a lake with significant The discharges of mine lodgement water important environmental constraint on Throughout New Zealand the use of water is controlled by a statute called the Water and Soil Conservation Act 1967. All industrial water users are required to hold Water Rights, which are in effect licences to take, use, dam, divert or discharge water. Water Rights are obtained through a legally defined process and any potentially affected party has the per to object to their granting. A special tribunal hears the evidence for and against an application, and issues its decision, which is reviewable in a higher court on Appeal. Rights, if granted, are issued subject to conditions and, in the case of mining discharges, limits would be set on flaw rate, suspended solids concentrations, turbidity, pH and the concentrations of any potential toxicants. This paper presents a case study of an integrated, catchment wide water management plan for Lake Waahi, that was prepared by the author, and others while the author was in the employ of CoalCorp, and its predecessor, State Coal Mines. The author is grateful to CoalCorp for their permission to submit this paper.

Jan 1, 1988

By Tapp B. A

The minerals industry in Australia is currently regarded as the country's economic saviour; the bastion of economic security. As Fitzgerald (1974) stated, 'Australia's natural endowments in minerals are the envy of most countries of the world'. As a result the proposed new mineral developments are on a scale that hitherto in the sixties would have been completely unenvisaged. It is reported that Australia is poised on the verge'of a sixteen billion dollar mining-based investment boom: a boom that will see Australia dominate the energy export field, the mineral processing field, and create the 'coal dollar'. This growth scenario has many inherent dangers, and it is the authors' contention that these should be carefully considered before further development proceeds. Two of the major problems related to the mineral industry growth scenario are the predictability of the future metal market, and the energy cost of mining. The latter problem is the one discussed here. The mining-mineral processing industries in Australia currently use about 36% of Australia's primary energy

Jan 1, 1980

By Yaniuk DW

The sampling of non-ferrous concentrates from trucks and trains has long been carried out either manually or by automatic spears. Very little use has been made of conventional sampling systems for sampling concentrates at transfer points, or cross-belt samplers for sampling from the belt as the concentrate moves along the conveyor.Due to the high value of base metal concentrates and the often extremely heterogeneous nature of the material it is imperative that the sampling procedures adopted are accurate and precise. The basic principle that all particles in the stream have an equal opportunity to be included in the final sample is not fulfilled by accepted traditional concentrate sampling procedures such as the spearing of wagons, trucks or streams. This may lead to significant bias being introduced into the final sample.Consequently, the application of correct sampling procedures, either with conventional cross-stream samplers or the newer cross-belt samplers, is of prime importance.SGS Australia has recently installed a number of cross-belt samplers for the sampling of base metal concentrates both in Australia and overseas. The application of these samplers will be discussed with emphasis on the benefits of their use.

Jan 1, 1976

By Jensen B

The investigation of the explosion characteristics of nine Bowen Basin (Central Queensland) dust samples in a suitable coal dust explosion chamber using a new dust concentration probe provides several advances in the area of coal dust explosibility testing. The 20 litre explosion chamber, of novel design, uses rotation of the main body of the chamber together with air jets for dust dispersion, and allows testing of different types of explosion initiators and analysis of the explosion characteristics of coal dust/methane mixtures of varying concentrations.A new development was a dielectric dust probe for the measurement of coal dust concentration. A capacitive micrometry technique was successfully adapted to measure dust concentration. The system uses a ratio-transformer bridge for measurement of small changes in a capacitive probe designed to sample a representative volume. The device is accurate, and is capable of operating in the hostile environment within the explosion chamber.The explosion chamber and dust probe characterise the explosive potential of coal dust samples by determination of the dust lean limit concentration in varying mixture with methane. Plots of lean limit points obtained in this way present an explosion curve for each sample which indicates the potential of the coal dust/methane to explode under the conditions of initiation in the chamber. The explosion curve obtained for each sample presents a unique signature that appears to reflect the physical and chemical characteristics of the dust.The results from this series of laboratory experiments appear to provide a useful index and indicate potential areas of interest for future research.

Jan 1, 1991

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

The influence of strongly chemisorbed solutes such as oxygen and sulphur on the rates of reactions at the gas-liquid iron interface is briefly reviewed. Deductions from recent studies of the rates of decarbur- ization of carbon-saturated liquid iron indicate ideal adsorption behaviour for sulphur over a wide temperature and composition range. This is in fair accord with available infor- mation on surface tensions in the Fe-C-S system. Previously unpublished results for the kinetics of the 14C02-CO exchange reaction are in accord with ideal absorption of oxygen on liquid iron. The derived value for the ideal adsorption coefficient of oxygen at 1550¦C is in quantitative agreement with measurements of the depression of surface tension in the Fe-0 system. Consideration is given to the applicability of such results to the violently agitated systems of steelmaking.

Jan 1, 1980

By L B. Sukla, V N. Misra

Microbial desulfurisation of coal has significant advantages over physicochemical desulfurisation processes since the former process selectively removes the inorganic sulfur compounds and heavy metals without significant carbon loss. The purpose of this study was to improve the desulfurisation yield of a coal sample from northeastern coalfields, Assam, India using microbial technique. The coal sample contained 2.13 per cent of total sulfur and 2.59 per cent of ash. Stirred tank reactors of 40 L capacity were operated in batch mode. Initially, the reactor was fed with 40 L of slurry containing ten per cent (w/v) coal, ten per cent (v/v) inoculum of mixed culture of mesophilic acidophiles, native to coal itself and the requisite amounts of constituents for 9K medium without added ferrous sulfate. The percolate of the reactor was then used to seed the medium for the next experiment. The purpose was to obtain a better adapted and more active biomass which would give a better desulfurisation yield for coal. Further studies were conducted in the bioreactor, fed with 40 L of slurry containing ten per cent (w/v) pulp density of coal, ten per cent inoculum (derived from previous studies) and the medium, supplemented with ferrous sulfate. Results showed an increased total desulfurisation yield of 43 per cent in the latter treatment in comparison to the previous one, where the desulfurisation yield was only 23 per cent. The findings also demonstrated the convenience of using inocula derived from coal, where 50 - 60 per cent of pyritic sulfur was removed, while chemical desulfurisation is of little significance with the majority of coal types. The ash content was also reduced to 1.74 per cent as the low pH of the process caused dissolution of a number of common minerals present in the coal.

Jan 1, 2004

By Yaroshenko YuG, Bokovikov BA, Gordon YaM

Problems of the effect of the number of tuyeres and their parameters on the uni- formity of gas distribution are invest- igated with the use of the authors' devel- oped mathematical model of the movement of gases and materials in the blast furnace. It is shown that the improvement of uni- formity of gas distribution with an increase in the number of tuyeres has a damping character. An analysis of the errors of the specified assumptions of the hypothesis concerning the potentiality of the gas movement in the bed is carried out. It is established that the potential approach model gives good results with the determination of the discharge of gas and its stress field, but is not useful for the calculation of local velocities of gas in the raceway. The results of trials of calculation investigations of the dynamics of form- ation of the raceway and the voidageòfield in beds of burden materials are presented in the concluding part of the paper.

Jan 1, 1981

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By de Vries D, Wilson EG, Henderson GAM, Carter EK

Canberra is a planned city in which the natural environment, rather than existing development and land tenure, has until recent times at least, imposed the major constraints to development. Even redevelopment poses fewer problems than for most cities. Geological conditions have, therefore, played a significant role in determining its shape and layout. The Canberra experience has relevance for major new mining and engineering projects. The role of engineering geologists and geophysicists in Canberra's development is described, and the problems arising from the geological environment are illustrated by several case histories. Four aspects are addressed: pre-development urban geology; major engineering projects; resources evaluation, including groundwater; and post-development problem-solving. The Australian Capital Territory lies within the Palaeozoic Lachlan Fold Belt. Within the ACT the belt is composed of folded and faulted metasiltstones, metasandstones and acid volcanics, intruded by a major granitic pluton. Some limestone lenses occur. The region has been part of a land mass since Late Devonian times and landscape evolution has been very complex. Geological features of special geotechnical significance include deep but variable weathering, with slight to moderate weathering along faults to at least 70 metres depth in places, and consequential foundation problems; close jointing; weathered limestone lenses with solution cavities containing clay and water; confined aquifers containing artesian water in scree deposits flanking hills; the presence of pyrite; and poor quality and low volumes of groundwater.

Jan 1, 1986