Search Documents

By Knight J. L, Baker G

The Wonthaggi coalfield is in South Gippsland, about 90 miles southeast of Melbourne. It is situated on the down-faulted block of the South Gippsland highlands that lies south of the Kongwak fault, between the Powlett River and the sea (Fig. 1). The coal, which is of Jurassic age, occurs in two small, and intensely faulted, limnic basins, that lie on either side of a concealed ridge of Silurian sediments. The coal was first found as thin seams outc1'opping in the cliffs at Cape Paterson, but the seams that are worked at Wonthaggi are concealed beneath a veneer of Cainozoic sands that covers the Jurassic strata, and were found by boring.The c9al seams are worked by the State Coal Mine, which was opened in 1909 to ensure a supply of coal for the Victorian railways, following a prolonged strike in the Newcastle field of New South Wales. The total production from 1910 to June, 1943, amounts to 13,918,800 long tons of coal. The coal seams are faulted to a degree unknown in most coal...

Jan 1, 1944

Various aspects concerning gold are mentioned below. These have no common theme but suggest points of interest any one of which, if warranted, could lead to development later and elsewhere. 'High level' auriferous gravels The gold deposits of Victoria are commonly classified as being either primary or secondary. Most primary occurrences comprise gold present in quartz reefs, together with other lode-like occurrences in which gold is associated with various sulphides, with or without quartz. Secondary occurrences are derived by physical release of primary gold and subsequent concen- tration of it as a constituent of sediments. Secondary gold deposits may be themselves eroded so leading to third or even fourth generation gold.

Jan 1, 1982

By Tonks E. E

The earliest discovery and mining of coal in the northern area of the Greta Coal Measures at Anvil Creek in 1862 was by William Farthing, however, some official records attribute the discovery to Thomas Frost in 1864. Frost's discovery was examined by William Keen, government examiner of coalfields, and further prospecting was carried out. This was followed by the pioneering work of C S Wilkinson, government geologist in 1884. Subsequently in 1886 C S Wilkinson entrusted a detailed survey of the coalfield to the then geological surveyor, T W Edgeworth David.The outcrop of the Greta Coal Measures around the Lochinvar dome was mapped by Edgeworth David and as soon as he reported his discovery, the Department of Mines reserved in the interests of coal mining an area of 23700 acres, which extended between what became the South Greta and Abermain No I Collieries.

Jan 1, 1993

Although forty-seven years have passed since the by-product coke oven made its successful commercial appearance, it is only during the past fifteen or twenty years that this system of coal carbonisation has advanced rapidly to its present position ofabsolute supremacy.Early designs of by-product ovens proved more or less faulty, and the coke produced was so inferior to coke made in beehive ovens that there was a natural hesitancy on the part of coke producers to invest large sums of money in installations of by-productovens of doubtful utility-more especially in view of the fact that beehive ovens could be erected cheaply and operated by non technical labour for the production of high-grade coke under the most variable conditions of trade.Surely and steadily designers brought forward by-product ovens of improved type, coupled with more efficient apparatus for the recovery of by-products, but still the industry lagged, due almost entirely to the insistence on the part of coke users that the qualityof ordinary beehive coke was vastly superior for metallurgical operations to the best coke produced from by-product ovens. So deep rooted was this prejudice that only the passage of time could eradicate it. That it has successfully done so is strikingly illustratedin the following statistics:

Jan 1, 1928

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

By M D. Goodz, Wright R. F

This paper highlights the importance of accurate observational technical reports compiled by Mining Geologists and Engineers. Before uncovering the original reports in July 1992, all previous investigations discounted returning to old mining areas on the belief that all operations were suspended because they were 'unpayable'. However, the detail of the original reports removed any doubt of the economic value of retrieving remnant ore.The important feature was that the description of 'unpayable' by GMA could be equated to 11.6 - 35 g/t over the history of the mine. On the basis of these reports the Morning Star mine has been re-opened.

Jan 1, 1993

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

By A Hacket, M Haest, I Vitins

Infrared spectroscopy has the ability to accurately measure mineralogy of drill cores, allowing for better spatial characterisation of iron ore deposits and potentially improving the prediction of key mining and processing parameters at the deposit scale. BHP Billiton Iron Ore is using infrared spectroscopic drill core logging to provide fast and accurate mineralogy for diamond cores and reverse circulation (RC) samples.Mineralogy can be predicted from infrared spectroscopic drill core data with errors on estimates ranging from six to 12 weight per cent. The error on the clay estimates is significantly lower than for hematite and goethite content estimates. This manuscript presents the results from a study on a bedded iron ore deposit, hosted in the Brockman iron formation, for which infrared spectroscopic data were collected on all of the diamond and RC drilling. Results show that these mineralogy estimates improve drill core logs, the geology model and the metallurgical block model.CITATION:Haest, M, Vitins, I and Hacket, A, 2013. Infrared spectroscopic drill core logging - making inroads to deposit scale 3D mineralogy, in Proceedings Iron Ore 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

This paper reviews the issues of mining machinery automation with special emphasis on underground applications. Automation is desirable because it offers the following advantages: ò increased safety by reducing human exposure to hazards of underground mining; ò higher productivity; and ò reduced wear of equipment. In spite of these advantages and in spite of numerous attempts over the past several decades, mining automation has been a difficult proposition, partly because no two mining operations are exactly alike and these operations are carried out in an unpredictable environment. This is the main difference between automation in factories and in mines and that is why mining automation has been lagging so far behind factory automation. Automation is possible only when the machine 'knows' its workspace. In a factory, this workspace can be 'described' to the machine because it is sufficiently controlled. In a mine, the environment undergoes continuous change and the only way the machine can 'know' its workspace is through real-time sensing.

Jan 1, 1995

By Johnson N. W, Ralston J, Lauder D. W, Smart St C R

The flotation behaviour of the Hilton ore of Mount Isa Mines has been examined in the presence of two collectors (sodium ethyl xanthate (Ex) and sodium diisobutyldithiophosphinate (3418A)) over a range of flotation Eh values and collector additions. Tests were also conducted in the absence of collector to determine the relative contributions of natural and self-induced floatability of the major minerals in the feed. In these tests the influence of metabisulphite on the self-induced floatability of the minerals was also determined. Attention focussed on optimising the selectivity of galena flotation. It is shown that the Hilton ore sample contained lower levels of naturally hydrophobic iron sulphide minerals than are generally contained in the Mount Isa lead-zinc ore. Furthermore, the self-induced floatability of galena was less than that exhibited by the galena in the Mount Isa lead-zinc ore. Sodium metabisulphite (MBS) reduced the self-induced flotation of galena but had no effect on the natural floatability of the iron sulphide minerals.

Jan 1, 1991

By Palmer W. T

The successful re-opening of the Cobar min- eral field was dependent upon the success- ful introduction of highly productive, low cost mining. Mechanised cut and fill stop- ing with incline access was selected for the C.S.A. mine because it permitted flexi- bility, complete primary extraction with no secondary pillar recovery, minimised dilu- tion and oxidation, a minimum of pre-pro- duction development and because diesel powered load-haul-dump (L.H.D.) units were proving reliable and highly productive in the U.S.A. Although L.H.D. vehicles are the key to the success of the mining method, four other main groups of vehicles are utilised in the mine - trucks, scaling vehicles, ser- vicing vehicles and specialist vehicles. The operating requirements at the C.S.A. mine are more stringent than those encount- ered in many other underground mining oper- ations. The first L.H.D. vehicle used at Cobar - the Transloader - had considerable difficulty in loading and discharging coarse production ore. The Wagner ST5 Scoop Tram performed this duty much better. However, the first generation Scoop Trams were not robust enough to withstand the heavy duty and many modifications were necessary before acceptable availabilities were obtained. Similar modifications were necessary for the Eimco 916 vehicle but the Eimco 915 unit came much closer to meeting the duty requirements. Eventually Cobar technical personnel design- ed a L.H.D. vehicle to meet specific C.S.A. mine conditions. These units have proven most satisfactory. Over 8 years of operation the underground vehicle fleet has become a proliferation of vehicle types. A standardisation pro- gram has been initiated based upon common prime movers being mated with "trailer" units to serve specific functions. Standardisation will reduce inventory levels and facilitate training of operating and maintenance personnel.

Jan 1, 1973

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

By Reeves I. And Farquhar J, Pearce S

The irregular shape of the Rosebery orebody, coupled with the inconsistencies in grade over short strike lengths, has meant stoping blocks have had to be small to combat dilution and stability problems. In the past, each lens was divided into regular block sizes and developed up to five years before production commenced. There were two major drawbacks to this practice; firstly, existing development deteriorated over time therefore requiring rehabilitation prior to production. Secondly, the pre-determined blocks could not be easily changed to incorporate changes in mining technology or economic circumstances. Bearing these problems in mind, it was evident that any new lens development had to be designed to allow maximum flexibility. The lens being currently developed is J lens. It represents approximately 50 per cent of the current reserves tonnes, and 65 per cent of the zinc metal. Its importance to the mine's future cannot be over emphasised. At its core the lens is up to 25 m thick at grades of over 30 per cent zinc. The practice of dividing the orebody into levels and sublevels, with consequent crowns was no longer acceptable because of restrictions in stope design and potential loss of ore. To assist in the development planning of J lens, a geostatistical block model was applied in long section to graphically represent the lens. Areas of high zinc concentration, as well as zones of uneconomic material were identified by using the model. This has meant that the development could he targeted, enabling stope delineation to occur in the lens without significant ore loss. Because of limited development resources, and the need to bring J lens on-line in the near future, the development strategy has had to focus on 'just-in-time' principles, rather than accessing the whole lens from bottom, and progressing upwards. Tight development schedules have required individual stoping block to be developed on such factors as grade and available tonnes rather than as a vertical sequence.

Jan 1, 1993

By Williams P

The assumptions made in conventional (Terzaghi) consolidation theory are not met in a tailings deposit. Finite or large strain consolidation theory must be employed. The paper describes such a consolidation model and its application to the design of tailings impoundments, water management systems, and long term rehabilitation.

Jan 1, 1990

By F Djukic, T Fisher, G Irving

Questionnaires were sent to 12 underground metalliferous mines in Queensland to enquire how these mines control diesel emissions from mobile diesel engines used underground. Where responses or controls were absent, discussion has been provided. A significant finding concerns secondary ventilation design rates. Some mines were designing ventilation rates to meet the superseded Mines Regulation Act of 1989 which required 0.04 m3/s/kW. The current Queensland Mining and Quarrying Safety and Health Regulation (2001) is risk based. In line with other jurisdictions, including New South Wales (NSW) and most Provinces in Canada, a minimum ventilation rate of 0.06 m3/s/kW is acceptable. However, this design ventilation rate will vary in practice depending on the diesel engines and controls. Dedicated ventilation engineers and technicians should be appointed to evaluate the effectiveness of the ventilation system. Personal exposure monitoring is required to confirm that exposure standards are not being exceeded. The primary control practice should be to reduce the emission at source. This can be ensured by purchasing low emission (Tier 2, Tier 3) equipment. In addition, the use of ultra low sulfur fuel (et al, 2002). Diesel fuel with a low aromatic content such as Eromanga diesel fuel will also mean employees are exposed to lower levels of poly-cyclic aromatic hydrocarbons. These controls should be carried out in parallel with good maintenance practices. Preventative maintenance should be programmed and emissions be routinely tested, including both gaseous and particulate pollutants and compared against defined criteria. According to McGinn, 2002, there are a number of fundamental tools necessary to carry out preventative maintenance. These are outlined in maintenance guidelines and best practices for diesel engines in underground mining produced for the Diesel Emissions Evaluation Program (DEEP). An effective diesel emission management system needs to be fully integrated within the Safety and Health Management System. These requirements are further discussed in this paper.

Jan 1, 2007

By T Gill, A Faragher, B Scott, V Kakebeeke

In 2000, after six year intensive exploration for high-grade haematite deposits, Rio Tinto included the channel iron deposits (CID) as a specific iron ore target in the Hamersley Province iron ore exploration program. The exploration model was simple and based on the then current understanding of CID genesis. Fundamental to the model was an interpretation that CID deposits after their final accumulation stage could be entirely concealed in their channels. Inversion to mesas and therefore exposure of the CID profile would only occur in areas where the modern drainages follow the ancient and have significantly incised their current bedrock. The model took encouragement from observations at Bungaroo Creek, where large CID accumulations occur in a deep valley incised in the Wittenoom Formation concealed below recent valley fills derived from the surrounding BIFs. Also, in the headwaters of the Yandicoogina system CID occurs below a more recent cover of calcrete and clay. After a number of failed or partially successful attempts, exploratory drilling in 2002 in the Caliwingina valley in the northern Hamersley Range identified significant CID mineralisation. Subsequent drilling programs from 2003 onwards revealed the presence of a large CID system, which stretches from the middle reaches of the Caliwingina Creek to deep under the sediments of the Fortescue Valley, a channel length of more than 30 km. Although the drilling is still somewhat sparse, the geological resource estimation suggests that Caliwingina is presently the third biggest CID system of the Pilbara (after Yandicoogina and Bungaroo Creek) and is of comparable size to the premining Robe River system (1.6 Bt), with comparable Fe-grades to the Yandicoogina global resource grade (57.7 per cent Fe). Large detrital and canga deposits overlie the Caliwingina CID, or interfinger with it, and although the economics of these are presently unfavorable, could ultimately present a low-grade iron resource of slightly smaller size to the CID mineralisation at Caliwingina Creek. Together with the recently discovered Serenity and Solomon deposits, as well as Cabbage Gum Bore and other smaller occurrences, the Caliwingina Creek deposit is part of a major new CID district in the central Hamersley Ranges, approximately halfway between Yandicoogina and Robe River. Although exploration in this new district is still underway, the preliminary indications are that this area will provide a total CID resource well over 3 Bt, and is on a par with the major known CID systems in the Hamersley Province.

Jan 1, 2009

The Ore Reserve System implemented at Mount Isa for Mount Isa Mines Limited is a comprehensive' computer system designed to process assay, geological, structural and survey data for Isa and Hilton Mines. This paper outlines the achievements of this system to date and by example, discusses the various reports and plotted output available. __ The impact of the ore reserve system particularly within the-Geology and Mine Plan ning Departments is reviewed in terms of new approaches to ore reserve calculations, evaluating the economics of various mining methods and reviewing preliminary stope designs. The compilation of metal distributions for both copper and lead orebodies at varying cut offs and reducing the involvement of skilled personnel in preparing non-standard plots of borehole paths are discussed. Options available through the system and their applications are outlined together with the planned future development of the system.

Jan 1, 1974

By McNabb KE, Ward B, Dyer G

Roof conditions at Southern Colliery, the second longwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 in thick roof beam either bonded or detached, with either a 2 in or 5 in overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992