Search Documents

By Edward J. Way

+1KLEINFONTEIN GROUP CENTRAL ADMlNISTRATION, BENONI, TRANSVAAL, S. AFRICA. The cost and the speed of sinking a shaft are factors of so great importance in operating a mine, that the data given in Table I., herewith published, will be of interest and value to all engaged in practical mining; and for this reason the data are communicated for permanent and accessible record in our Transactions. The figures 'of cost cover the period from January 1, 1903, to May 31, 1903, during which time the total depth sunk was 858 ft. So far as I know, the cost of sinking per foot (£13,15s., 11.04d.) of a shaft of the dimensions 21 ft. by 6 ft. in hard rock, is the cheapest yet on record; and the speed of 213.5 ft. per month, which was attained during May, 1903, is also the best record for speed in sinking in rock so hard as that of this shaft. During the period from January 1 to May 31, 1903, there were 144 rounds worked, involving 4,032 holes, of a total depth of 28,963 ft. 2.4 in., which is equivalent to an average depth of 7 ft. 2.2 in. per hole bored. These data are of added interest from the fact that the work was done practically by native labor.

Jan 1, 1905

By Daniel C. McLean

Copper concentrates produced by many operations in the United States and South America contain chalcocite (79.9% Cu) as a major component, yet the grades of these concentrates rarely exceed 25 to 28% Cu. Mineralogical studies made by E.P. Cadwell indicated that the low grades were caused by dilution by pyrite rimmed with secondary chalcocite. Laboratory and plant tests proved that concentrates could be significantly upgraded by using a simple, low cost cyanide leaching technique to dissolve the rims and reject the pyrite. The many advantages of this new procedure are cited and the process steps and a typical flowsheet are described.

Jan 1, 1984

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

COMMITTEE ON INCREASE OF. MEMBERSHIP. C. R. CORNING, Chairman. ADOLPHE E. BORIS, First Vice-Chairman. THOMAS T. READ, .Secretary, Woolworth Bldg., New York, N. Y. Vice-Chairmen. JOHN H. ALLEN, GEORGE M. COLVOCORESSES, RICHARD AL ATWATER, JR., ROBERT PEELS, GEORGE D. BARRON, CHARLES P. PERIN, A. CHESTER BEATTY, JOSEPH A. VAN MATER, J. PARKE CHANNING, ARTHUR L. WALKER. D. C. Bard, Howard Eckfeldt, Philip N, Moore, W. de L. Benedict, R. C. Gemmell, T. H. O'Brien, John C. Branner, F. Louis Grammer, James J. Ormsbee, Palmer Carter, Ernest A. Hersam, Edward W. Parker, Allen J. Clark, Edwin C. Holden, John B. Porter, F. Crabtree, William L. Honnold, R. M. Raymond, George G. Crawford, Reginald E. Hore, Robert H. Richards, O. C. Davidson, C. Colcock Jones, LeRoy Salsich, E. V. D' Invilliers, Eugene P. Kennedy, Frederick H. Sexton, James S. Douglas, Chester F. Lee, Henry L. Smyth, Walter Douglas, - Richard S. McCaffery, F. W. Traphagen, Howard N. Eavenson, James F. McClelland, Elton W. Walker. Milton H. McLean, Meetings of this committee were held at the Institute headquarters on April 18, and May 2 and 15. It was resolved that meetings shall be held monthly on the third Friday of each month.

Jan 6, 1913

By Raphael Titi-Manyaka, I. Iwasaki

Chlorination and chloridization behaviors of pyrite, pyrrhotite, chalcocite, covellite, chalcopyrite, bornite, heazlewoodite, millerite, and pentlandite in chlorine, gaseous ferric and sulfur chlorides were investigated by thermogravimetric analysis. The reaction mechanisms are discussed in terms of theoretical weight changes, thermodynamic calculations, and X-ray analyses of reaction products. The experimental findings are in direct application to the development of a scheme for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from complex sulfide flotation concentrates.

Jan 1, 1977

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949

By Arthur F. Colombo

The selective flocculation, desliming and flotation process developed by the U.S. Department of the Interior, Bureau of Mines, as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The application of the selective flocculation and cationic flotation process to three oxidized taconites from the western Mesabi Range in Minnesota is discussed. Data from the operation of a 408-kilogram-per-hour (900 lb/hr) pilot plant employing reclaimed water are summarized for the three types of oxidized taconites.

Jan 1, 1980

ST. LOUIS LOCAL SECTION Executive Committee ARTHUR THACHER, Chairman R. A. BULL, Vice-Chairman WALTER E. MCCOURT, Secretary-Treasurer, Washington University, St. Louis, Mo. H. A. BUEHLER R. R.-S. PARSONS HERBERT A. WHEELER On the afternoon of May 1, 1915, 42 members of the St. Louis Section, as the guests of E. S. Catch, President, and his associates in the Granby Mining & Smelting Co., visited the new zinc smelter of that company at Roselake, Ill. The annual meeting, which was preceded by a dinner at the St. Louis Club, was attended by 54 members and guests. The Chairman, H. A. Wheeler, presided. The Chairman rendered a report on the activities of the Section during the past year and the Treasurer presented a financial report. The following Executive Committee was elected: Arthur Thacher, Chairman; R. A. Bull, Vice-Chairman; W. E. McCourt, Secre-tary-Treasurer; H. A. Buehler, R. R.. S.. Parsons. H. A. Wheeler, as retiring Chairman, retains membership in the committee. W. L. Saunders, President of the Institute, made an address. H. W. Gepp, of Australia, described the lead and zinc deposits of Broken Hill, Australia, and V. H. Hughes, of Tulsa, spoke on the geology of the Cushing oil pool, Oklahoma. WALTER E. MCCOURT, Secretary.

Jan 6, 1915

By J. R. Thoenen

THE Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy.

Jan 1, 1947

By AIME AIME

THE portrait of Herbert Hoover, President of the United States, recently painted by Philip A. de Laszlo at the request of the four Founder engineering societies, was unveiled at a special meeting in the Engineering Societies Building on Feb. 15. The portrait was delivered by Gano Dunn, chairman of the Hoover Medal Board of Award, who said, in part:,

Jan 1, 1932

By J. T. Eash, E. M. Wise

MANY of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. SCOPE AND CONCLUSIONS Tensile tests were carried out at room temperature and elevated temperatures up to 11000 C. on previously well annealed samples of platinum, palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100° C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the- other materials tested. The tensile strengths of palladium and the palladium alloy at 1100° C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at tempera¬tures above 600° to 800° C., while the two samples of pure palladium show a maximum at 600° C.

Jan 1, 1938

By C. A. Crawford

Nickel and the nickel-copper alloy, the latter generally referred to as monel metal, are available in a variety of wrought and fabricated forms, of which the following are regular commercial products:

By R. D. Heidenreich, R. E. McNulty, C. H. Gerould

Jan 1, 1946

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

Jan 1, 1946

By P. D. Hunt, I. Johnson, M. G. Chasanov, H. M. Feder

The solubilities of the transition metals from scundium to nickel, inclusive, in liquid cadmium were determined by sampling saturated solutions. At 400°C these solubilities (ppm) are:Sc, Co, 22; Ni, 12000. Relative partial molal enthalpies and excess partial molal entropies at infinite dilution for the solutes Cr, Mn, Fe, and Co are compared zoitlz similar data for the post-transition metals. Three new intermetallic phases, ScCd,, TiCd, and Ti,Cd, encozaztered in the course of this work, are reported. Measurements of the solubility of the 3-d transition metals in liquid cadmium have been reported' only for iron. The present measurements for the entire series were made as an aid to the study of the systematics of alloy formation. EXPERIMENTAL The apparatus and sampling techniques used for the solubility determinations were similar to those described by Martin etal.' Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple sheathed in recrystallized alumina and immersed in the solution. The thermocouple was recalibrated periodically during the course of the investigation. Thermocouple voltages were measured to the neares 0.01 mv with a Rubicon model 2732 potentiometer. A scaled-down version of the apparratus, in which the total metal charge was about 90 g, was employed to measure the solubility of scandium. Two-mm ID Vycor filter pipets were used to sample the scandium-cadmiurn solutions; the samples weighed about 2g- Cadmium with a minimum purity of 99.95 pct was used; the only impurities detected spectrochem-ically were C'u and Mg, both less than 10 ppm. The purities of the other metals were: scandium, 99.9 pct; titanium. 99.92 pct; vanadium, 99.9 pct; chromium, 99).99 pct; manganese, 99.9+ pct; iron, 99.90 pct; cobalt, 99.95 pct; and nickel, 99.96 pct. Solidified melts were routinely analyzed spectro-graphically. No significant contamination by the crucible, sampling pipets, or other materials of construction was observed. The entire specimen obtained by sampling was dissolved to preclude analytical errors due to segregation on cooling. Colorimetric methods3 were used for the analyses of cobalt (2-nitroso-l-naphthol), manganese (permanganate), nickel (dimethylglyoxime), titanium (peroxide), and vanadium (thiocyanate).4 Chromium, iron, and scandium were neutron-irradiated to produce The dissolved samples were gamma-counted to determine solute concentration.For the separation of intermediate phases from cadmium-rich alloys selective leaching by saturated ammonium nitrate solutions was employed. The concentration of cadmium in the successive leaches was followed polarographically and the process was terminated when the rate of cadmium dissolution decreased markedly. For the further investigation of intermediate phases 1/4- in. diam powder compacts were pressed at 80,000 psi and annealed in argon at 315" to 330°C for 10 days. Larger quantities of alloys were prepared in sealed tantalum capsules heated in a rocking furnace.

Jan 1, 1962

A recent study estimates that a 10% improvement in the performance of wire rope used on draglines could save the US coal industry $2 million annually in rope costs. In addition, such an improvement could boost annual coal production by allowing the industry's draglines to remove an extra 1.5 million m3 (2 million cu yd) of solid overburden each year. These findings, although admittedly preliminary, suggest the magnitude of benefits that can be derived from a well-planned wire rope maintenance program.

Jan 3, 1978

By Pierre R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,1 and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.2-4

Jan 2, 1959

By Alexander Sattman, Anton Homatsch

Jan 1, 1894

By W. A. Bates, R. J. Miller

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By R. J. Miller, W. A. Bates

ALTHOUGH cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowy1 in 1930, which presented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids ; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. CONSTITUTION AND PROPERTIES Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen

Jan 1, 1946