Search Documents

By Clair Upthegrove, Elbert S. Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are: obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from. 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By Guido Bassi

IT is known'" that secondary recrystallization occurs in copper sheet with at least 90 pct reduction after annealing at high temperatures, 700" to 1000°C. Turkalo and Turnbull4 have found recently that secondary recrystallization might occur even after annealing at such low temperatures as 500°C for a high purity, coarse-grained copper sheet. It will be shown in the following that in an electrolytic tough pitch copper wire, with a high degree of deformation, secondary recrystallization might occur at even lower temperatures. A hot-rolled rod of 9.5 mm diam (temperature at which rolling commenced was 850°C) was drawn in continuous drawing machines to 0.4 mm, corresponding to a cross-section reduction of 99.8 pct. The texture in the center of the wire (the sample for X-ray analysis was etched to 0.15 mm diam) is a mixture of the [111] and the [loo] direction, as can be seen from Fig. 1. This is in accordance with the result of Schmid and Wassermann.' After a few minutes annealing of the wire at 200 °C, there is a noticeable recrystallization of the structure with a preferred orientation in the [l00] direction at the expense of the [Ill] deformation texture, as Figs. 2 and 3 show. Farnham and OINeill" reported a similar result. The final recrystallized structure shows mainly the [loo] orientation. There is however a small amount of [111] and random orientations. If the wire is annealed at 400°C, the recrystallized structure first shows a [loo] texture, Fig. 4, but as the annealing time is increased the fine-grained structure transforms into coarse grains, Fig. 5, giving a new preferred orientation, Fig. 6. The calculations show this to correspond to the [I121 direction. Even if the annealing that gives the primary recrystallization is carried out for six weeks at 20O°C, the same secondary recrystallization texture is obtained if the annealing is continued at 400°C. Schmid and Wassermann7 found the [I121 texture, but only after annealing at 1000°C or higher. The appearance of a secondary recrystallized

Jan 1, 1952

By Robert L. Grayson, Y. J. Wang, R. Mike Mishra

Prediction of ventilation needs in long range mining projections requires serious consideration when formulating those projections. Predicting the behavior of the ventilation system of an old, complex mine poses an especially provocative problem. Air-flow around and through mined-out areas via bleeder systems, leakage flows through stoppings or other air control devices, and the use of multiple fans all add to the basic complexity of a ventilation system and make predictions of ventilation changes very difficult. Fortunately, the task of making ventilation decisions can be greatly assisted by ventilation surveying and computer simulation. The Nemacolin Mine of Jones and Laughlin Steel Corporation, located in Southwestern Pennsylvania, is one such old mine which used the computerized approach successfully. A mine-wide pressure-quantity survey was used to obtain realistic values for airway resistance factors. These values, together with network topology, formed the basic input for computer simulation. Results from this simulation indicated that air quantities generated at critical airways by the model were generally within a couple of percent of those measured in the actual survey. It was then concluded that the model was acceptable for practical application, and it was used immediately for studying the effects on the ventilation system of changing the blade settings of fans. Additionally, the model was modified to incorporate projected mine development and used to predict future ventilation.

Jan 1, 1982

By C. C. Harris

A critical literature review leads to a descriptive model of tumbling mill operation based upon energy partition concepts and the necessary requirements for particle fracture. As grinding proceeds into the ultra-fine region, conditions which are of little significance during normal operations gradually become controlling. These involve increasing resistance to fracture and an increasing tendency to aggregate as particles become smaller, and a growing fraction of the power input being consumed fruitlessly. The result is that fineness asymptotes to a maximum value as comminution proceeds indefinitely; thus where t is time, p and n are experimentally determined parameters, and Ø is a measure of fineness, which is presumed to be proportional to specific surface area, or proportional to the reciprocal of the size modulus (provided that the distribution modulus remains constant with time), or both. Ø, is the asymptotic value of Ø and is a measure of the grind limit. A method for its graphical determination is given. In a previous paper1 the physical and mathematical principles requisite to a study of the role of energy in comminution were reviewed. The micro-process of comminution — or the comminution event — can be investigated in terms of (a) the magnitude of the force-field localized around the individual particles which gives rise to the stresses generated in the particles, which in turn induces their fracture, and (b) the distribution of fragment sizes, should the event prove fruitful. The entire fragmentation operation can be considered to be the totality of its individual events, and in order to obtain a single independent variable of the process it is necessary to transform and sum the local stresses in terms of energy.1 This energy, however, will account for only a fraction of the energy input to the comminution process, the actual magnitude depending upon the kind of mill and several related factors. From the comminution viewpoint the primary function of a mill is that of stressing as many as possible of the individual particles of the charge to failure, with the maximum economy of energy expenditure. This is difficult indeed to achieve, for stressing a particle does not always break it, while the overwhelming portion of the energy input is involved with various internal mill processes which — almost incidentally — determine the magnitude, frequency, and manner in which the forces are applied to the particles. Essentially, these processes depend upon the mill dimensions, loading and speed, and they may be little affected whether fracture occurs or not. These processes must be delineated if a complete description of the role of energy in comminution is to be given; the energy account sheet1 (Fig. 1) in showing how the energy is partitioned for the requirements of the several functions it performs, provides a framework for the development of a model of the comminution process. Actual numerical values for the variables appearing in Fig. 1 will depend upon the mill, materials, and operating conditions. A possible general relationship between the variables will be suggested in this paper. Before proceeding further, a cautionary note must be issued. It was pointed out in an earlier paper' that while energy input is not changed by increasing the power and decreasing the time in the same proportion, and vice versa, the results of the process in terms of particle fineness may be different. Thus, although energy is chosen as the independent variable of a comminution process, it is not absolutely independent, and care must be exercised to ensure that it is used within its range of valid application. Time has the necessary independence, and it will be used in place of energy where it is appropriate. The residence time in a mill is usually of the order of minutes. Under these conditions the particles are subjected to "... a relatively constant fracture producing environment".2 However, under the more rigorous conditions of greatly extended time, which pertain in ultra-fine grinding, indications are that the fracture producing environment no longer remains constant; this is the major subject of this paper. At this extreme limit the mill is probably taxed to its utmost, and at the same time the bulk material properties are becoming closer to ideal, while the physico chemical effects associated with surfaces, edges and corners are multiplying. (The edge length per unit volume is proportional to the square of the specific

Jan 1, 1968

By J. E. Johnson

OF the many items of information necessary to the successful management of the blast-furnace, few are more important than knowledge of the location and movement of the stock: line:—whether the furnace is full and has been kept so; whether the stock is settling regularly or slipping; and, if slipping, how often it has slipped, at what times, and how far at each time. To obtain these data, a man is sometimes stationed at the top of a pair of mechanically-filled furnaces, sim-ply to watch and gauge them by hand in the old-fashioned way. A more recent practice is the suspension of test-rods from ropes leading over pulleys to the ground-level, where the ropes are mound on small drums with graduated peripheries and provided with crank-handles, whereby the skip-man or some other person can quickly and conveniently gauge the position of the stock-line in the furnace. I believe the credit for this great improvement belongs to Messrs. McClure $ Phillips of Sharon, Pa., who were, as far as I know, the first to apply it, and who have a patent for it. The valuable indications gained by application of the Uehling pyrometer to the down-comer are not to be ignorcd; but the information thus furnished is somewhat indirect, and there is no scale for the translation of " top-temperatures " into " feet down." Moreover, this apparatus, as a whole, is delicate, and the cost of installation and maintenance is high. If the record furnished by the Uehling pyrometer is not in the most desirable form, the test-rods, on the other hand, give no record at all, except through the memory or notes of a man who, to say the least, is not gauging continuously, and who may omit to report an improperly low stock-line, if it be due to a fault of his own.

Jan 1, 1906

By Charles Catlett

THE rapid development of the Portland-cement industry implies that the country is being very carefully searched for material suitable for its manufacture. Such material can be found at a great many places ; but deposits thoroughly satisfactory in chemical composition, and at the same time meeting all the other requirements connected with the economic production and profitable marketing of the product, are exceedingly few, if I may judge from the investigations which I have had to make in a number of States. The raw mixture which by its clinking and grinding forms Portland cement contains approximately 75 per cent. of carbonate of lime. This is found in nature as limestone or marl. The natural rock commonly carries either more than the required percentage of carbonate of lime (in which case it has to be reduced by suitable admixture of clayey ingredients) or less-in which case purer lime carbonate has to be added. The controlling ingredient, therefore, is carbonate of lime, or limestone of the right composition. Among the most serious difficulties is that of finding limestones low enough in magnesia to meet the exacting requirements of certain specifications. All engineers recognize that there is a limit beyond which it is not safe to let the magnesia go; but within that limit there is considerable difference of opinion. Until that difference is finally settled, no one would be willing to invest the large sum of money necessary for a Portland-cement plant, if it were not certain that the usual requirements in this particular could be satisfied. The usual limit in well-established specifications is 5 per cent. of magnesium oxide in the finished cement, but many specifications limit the amount to 3 per cent. These figures

Jan 9, 1907

By J. S. Li, J. C. Edwards

A prediction is made of the airflow at the Bureau of Mines Lake Lynn Laboratory with a ventilation computer program that accounts for fan-driven forced ventilation and temperature-induced natural ventilation. There was substantial agreement between measured and predicted airflow rates. The capability of the program is demonstrated as a planning aid for ventilation under emergency conditions in a multilevel coal mine. Smoke spread in a multilevel mine is analyzed following the occurrence of two events, the failure of the main exhaust fan and the development of a fuel-rich fire in a passageway.

Jan 1, 1983

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By W. G. Fischer, S. R. Felde

Trona ore at the Westvaco, Wyo., mine of FMC Corp. has been obtained by room-and-pillar methods since the mine began operation. The flat- lying, 10-ft thick trona (Na2CO3.NaHCO3.2H2O) is covered by 1500 ft of weak shale and sandstone, and extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly, and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs, efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early '60s forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were also seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. However, since roof control in the longwall methods appeared to be more satisfactory than that found in room-and-pillar techniques it was believed that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 4, 1966

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By G. D. Gemmell

Effects of solid-sdutidn alloying with titanium, molybdenum, and tungsten at concentrations up to 10 pct on the strength of pure columbium at elevated temperatures (mainly 2000°F) have been investigated by means of creep-rupture, hot-tensile, and hot-hardness testing and recrystallization studies. ThIS paper presents some results from the initial part of a study of the effects of alloying on the high-temperature strength properties of columbium. The elevated-temperature strength characteristics of pure columbium were first studied. Binary alloys of columbium with titanium, molybdenum, and tungsten containing 1, 5, and 10 pct of the solute elements were chosen on the basis of their high melting points, their known solid solubility in columbium, and results of separate oxidation-resistance studies of columbium alloys. EXPERIMENTAL PROCEDURE All the materials used were of highest purity. A typical analysis of the columbium is shown in Table I. Compositions of the alloys are also given in Table I. To evaluate the strength properties of pure co-lumbium and the alloys at elevated temperatures, creep-rupture, hot-tensile, and hot-hardness testing was done on recrystallized material. To prepare the pure metal and the alloys for these tests, 1- 1b buttons were made in a water-cooled copper crucible, inert atmosphere, tungsten arc furnace. Tapered ingots, 3 in. long, were made from these buttons by a skull-casting technique and these were machined to 1/2 in. diam, swaged to 50 pct reduction (pure columbium at room temperature, alloys at lowest temperature possible without cracking, generally in range 1100" to 1800°F) and heated in vacuum (lo-' mm Hg) for 16 hr at 2550°F for re-crystallization and homogenization. The resulting grain diameter was 0.1 to 0.3 mm. The 10 pct Mo alloy casting was not successfully swaged at temperatures up to 1800°F without cracking and was not included in the test program. Creep-rupture testing was done at constant load in vacuum on cylindrical specimens of 0.16 in. diam, using Instron capsules. The pressure at test temperatures was less than 10-1 mm Hg. Hardneas readings taken on the test specimen before and after testing were used as a check on possible gaseous contamination. Hot tensile tests in vacuum on cylindrical specimens of 0.125 in. diam were also made with Instron equipment at a strain rate of 0.067 min.-l. Hot-hardness measurements were taken with a unit constructed at the Du Pont Experimental Station. The test piece, supported on an alumina anvil, and the molybdenum indenter shaft with sapphire tip is heated in a platinum-wound furnace. The load applied to the pyramid indenter is measured by strain gages attached to a proving ring located outside the hot zone. In the measurements reported here the load was I kg. The tester operates in a vacuum of about 10"5 mm Hg and is capable of temperatures up to 1400°C.

Jan 1, 1960

By E. T. Dumble

The history of the several petroleum deposits of Texas and Mexico, or of the sediments in which they now occur, if the deposits are not indigenous to such sediments, is known in a general way only, but it nevertheless casts strong light on the conditions surrounding them and is of great importance in the search for and exploitation of them. The petroleum deposits of Texas are separable into two main divisions: 1. The deposits of northwestern Texas, which are directly connected with the Oklahoma fields to the north, and have no representatives at all in the Mexican area. 2. The deposits of the coastal area, which extend into Louisiana on the east and connect with those of the Mexican coast to the south. Early in the Pennsylvanian period a series of bituminous shales and limestones were laid down over a broad area in Texas, Arkansas, and Oklahoma. These are known as the Bend series in Texas, the Caney shales in Oklahoma, and the Fayetteville beds in Arltansas. Following their deposition an uplift occurred, forming the Lampasas geanticlinal, which runs northeastward from the old Paleozoic land area of the Llano region toward Red River. The Bend series is petroliferous in places and has furnished a few producing wells on each side of the Lampasas uplift. This uplift forms the barrier and dividing line between the two divisions of the Texas petroleum deposits. To the west of it, in waters which were the southcrn extension of the interior continental seas, in connection with the sedimcnts and coal beds of the Pennsylvanian and Permian, great quantities of petroleum were deposited either as oil or as "potential petroleum." These sediments have been subject to very slight disturbance, and only very gentle folds are found, with no signs of volcanic action in any part of the area. The conditions, therefore, indicate that the greater part, if not all, of the oil in this area is indigenous to the beds in which it is found. East of the anticlinal the oldest beds which appear in contact with the Bend are the Trinity Sands of the Lower Cretaceous. No evidence has

Jan 1, 1916

By F. J. Meringer, C. W. MacGregor

Various investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-l2 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 S =1/A and where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. Preliminary Investigations The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 0.19 per cent; S, 0.118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Effect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By J. A. Bownocker

The existence of petroleum in the rocks of Ohio and Indiana seems to have been first shown by wells dug for salt. The fuel, however, was objectionable owing to its odor and inflammability. Not until the Drake well was drilled in 1859 did the people appreciate the value of rock oil, and then they at once began plans to secure the coveted fuel. The first successful well in these two states was near Macksburg, in southeast Ohio, where at a depth of 59 ft. (17 m.) oil was found in commercial quantity (1860). A year later this fuel was secured on Cow Run, in the same county, and at about the same time in Noble, Morgan and perhaps other counties in that part of Ohio. The second great step in the production of oil in Ohio and Indiana was taken in 1884 when the reservoir of natural gas in the Trenton limestone of northwest Ohio was tapped, and where a year later oil was secured in the same formation. Petroleum in this limestone was obtained in Indiana in 1889.' The third step in the production of oil in Ohio and Indiana is associated with the Clinton sand of Ohio. Natural gas in large volume was discovered in that rock at Lancaster, in 1887, and the area has been extended until it has become the largest individual producer in the world. The presence of natural gas in such great volume all but demonstrated to the driller that oil lay hidden near by. Soon the search for it was started but not until 1899 was petroleum in commercial quantity found in the Clinton sand, and a large pool was not located in it until 1907. The fourth step in the developrllrnt of the industry was taken in 1913, when the pool in Sullivan County, in western Indiana, was opened. The producing rock is the Huron sandstone, which is the topmost member of the Mississippian system.²

Jan 1, 1921

By Oswald J. Heinrich

IN this paper I shall attempt a description of the successful extraction of coal from this property after it had been on fire for probably fifty years, or more, and after attempts, made at various times, which had still left considerable coal behind. The Richmond coal-field has a well-founded bad reputation, arising from the circumstance that many of its collieries have had to be abandoned, from time to time, if not entirely, on account of fires, caused by spontaneous combustion, to which the character of the coal in this field renders them peculiarly liable. While I fully assent to the opinion that this trouble lies in the nature of the coal, which is highly bituminous, and the seams of which are, moreover, divided by slaty bands, through which, as also in the coal, iron pyrites is more or less disseminated, often in microscopically small particles, I must, nevertheless, declare that many lamentable disasters, causing great loss of life and property, could have been avoided if a suitable system of mining had been pursued in all the collieries. If this could not have been done from the be-. ginning of mining in this section of country (the history of which can be traced back to over one hundred years), at least experience enough existed upon this subject thirty and forty years ago to dictate the avoidance of the dangers to a considerable extent. I t is therefore necessary here to refer first, in a few remarks, to the character of the coal deposits, particularly in this immediate neighborhood, the Midlothian being one of the oldest and most extensive mines, and some of its coal being much subjected to spontaneous combustion. I must also refer to the history of former managements to explain more clearly the results which were arrived at. The Midlothian coal-mine property, situated upon the eastern outcrop of the basin, about four miles south from James River, exhibits

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado. The topography is rough, the mine and mill being under Battle Mountain and the adit entrance in the north wall of the canyon of the Eagle River, which is here a steel) gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles', this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent. There is a large historical background for underground plant construc-tion. From the dim past caves have been used for dwellings, stables, storage and shops. It was natural that where caves were available their many advantages led to their enlargement to suit convenience and where they were not available but the ground conditions, topography and, drainage were favorable, to the construction of artificial caves. In the vicinity of Epernay, France, extensive underground chambers protect the manufacture and storage of champagne-an intricate and ingenious application of chemical engineering-and in recent years these plants have been mechanized by the installation of conveyor systems. In the

Jan 1, 1937

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.'-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR's or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR's dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.'.' An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.'-' All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969

By Edward Richardson

As DEVELOPED up to the end of the Great War, an airplane was essentially a mechanism of wood and fabric, joined and held together by metal fittings and, fastening. The engine and accessories, wire for wheel spokes and other tension members, and the occasional use of metal for interplane struts and the shafts of surface controls required some metal, but essentially it was a. wood and fabric structure. Attempts had been made to use metal for other purposes, such as struts in the drag-trussing of wing panels and for short interplane struts, and Junkers had produced an airplane of iron in 1915. By 1917 he was using steel tubes and duralu-min sheets, securing noteworthy advantages aerodynamically and from the standpoint of weigh PRINCIPLES OF AIRPLANE CONSTRUCTION The loaded weight of airplanes ranges from 500 lb. for the light plane of which we heard so much a short time ago, to about 40,000 lb. The great majority of planes range from 2000 to 10,000 lb. Of this weight from 15. to 30 per cent. is for the dividend-earning load. This percentage is so low that every per cent. saved on the rest of the weight increases the pay load from 3 to 6 per cent. The economic value of every pound that can be saved in designing or constructing a plane is sufficiently great to warrant spending money on refined methods of structural analysis, materials of superior strength properties for a given weight, methods of manufacture which may make possible the use of refinements in structural design, and the like, to an extent unknown heretofore.

Jan 1, 1928

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940