Search Documents

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By George R. St. Pierre, John Chipman

METALLURGISTS have been studying the chem-ical behavior of sulfur in steelmaking for many years in order to have a better control of the sulfur content of finished steel. During the refining period in the open hearth, molten steel is separated from a gas phase by molten slag. Chemical reactions occur principally at the slag-metal interface and at the slag-gas interface. A need for physical-chemical investigations of reactions between sulfur-bearing gases and steelmaking slags was recognized some time ago.'.' From the early work, it can be qualitatively concluded that increased sulfur content and low partial pressure of oxygen in the gas phase favor the passage of sulfur from gas to slag. Using radioactive sulfur S Koch and Fink' have demonstrated the rapid rate of exchange of sulfur between gas and slag in an open hearth furnace. Gurry and Darken and Darken and Shields (as reported by Derge and Marshall') have equilibrated lime-iron oxide slags with SO—O2 gas mixtures. The major conclusion from the reported results is that sulfur content increases with increasing lime content in lime-iron oxide slags equilibrated with a gas of high oxygen pressure (10-2). The data were interpreted as indicating the presence of SO, and S,O, ions. Richardson and Fincham' have conducted the most extensive experimental study of sulfur equilibria between gas and slag. Their results confirmed many of the conclusions drawn from calculations of Richardson" and Withers. Richardson and Fincham's data fitted very well into the sulfur scheme represented by the reactions 1/2 s2 (g) + (0) melt - 1/202(g)+ (S) melt [II 1/2 S, (g) + 3/2 O (g) + (0) melt - (SO,) melt. [2] At oxygen pressures greater than 10 to 10 they found that reaction Eq. 2 was predominant while reaction Eq. 1 was controlling at oxygen pressures less than 10." to 10.". The slag compositions and gas mixtures used in their investigations were different from those used in the present study. Wherever possible, comparison has been made between their results and these, and agreement is excellent. It is evident that the distribution of sulfur between slag and gas depends upon the oxygen pressure of the gas. In FeO slags, a change in oxygen pressure produces a change in ferric oxide content, and a knowledge of this equilibrium is a prerequisite to studies of sulfur distribution. The data are found in the work of Darken and Gurry" on the FeO system and the more recent experiments of Gurry and Darken" and of Larson and Chipman" on FeO slags containing lime and silica. The effect of oxygen pressure on the ratio Fe /(Fe" + Fe ), the so-called j-ratio, reported by these investigators will be used in interpreting the results which follow. Experimental Method The purpose of the experimental program was to determine the equilibrium sulfur content in slags exposed to gases of known oxygen and sulfur pres- sures. The slag compositions selected for study were from the lime-silica-iron oxide system. Additions of magnesia were made to some of the slags. Apparatus—The apparatus used by Larson and Chipman was modified slightly to accommodate the addition of SO2 to the gas mixtures. As in their work, slag samples of 0.5 to 2.0 g were held at temperature (lcc) in platinum crucibles under a steady stream of gas, 100 to 200 ml per min, for several hours and then rapidly lowered to the bottom of the furnace where they were quenched in mercury. Preparation and Analysis of Gas Mixtures—Mixtures of SO,-CO were prepared from Virginia Smelting Co. Extra Dry liquid SO, and Pure Co. CO,. After removing traces of water vapor with an-hydrone, the CO, was passed over graphite at 1200°C, at which temperature the conversion to

Jan 1, 1957

By A. W. Furbank

In reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65". The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95". Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, particularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typical of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45" relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140". Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable. Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1941

By A. W. Furbank

In reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65". The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95". Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, particularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typical of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45" relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140". Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable. Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1941

By W. A. Backofen, D. Lee

The deformation of textured sheet of titanium and several of its all-a (hcp) alloys was investigated with two kinds of experiments: tension testing along different directions in the plane of the sheet, and combined-stress loading along the principal axes of anisotropy (the rolling and transverse directions). Texture and plastic anisotropy were evaluated with pole figures and by measurement, as a function of orientation, of the tensile transverse-strain ratio, or R parameter. The results as a whole can be rationalized qualitatively with the present understanding of deformation mechanisms in titanium. Quantitative agreement between the orientation dependence of tensile yield strength and the Predictions of continuum ANISOTROPY in the properties of engineering materials is more the rule than the exception because anisotropy in structure is so common, and the one generally follows the other. Two broad categories of structural anisotropy are represented by mechanical fibering and crystallographic texture. The former is important in many aspects of fracture.' The latter has more significance for yielding and plastic deformation, theory, using the R measurements, was relatively poor. However, in tension-tension quadrants of the yield-locus diagrams, the difference between theory and experiment was hardly more than 10 pct. The maximum texture-hardening effect was found in a 4Al-1/4O2 alloy to be nearly 50 pct. In the compression-compression quadrant, {1012} deformation twinning prevented the locus from expanding much beyond the Position predicted for isotropic material. With increasing temperature the trend in R was downwards, approaching unity (isotropy) near the a-transus temperature; an accompanying development was large amounts of neck-free extension. which are of special concern in this paper. The tendency has been to view crystallographic texture more as a liability or curio than as an asset. The prominent exception is found in silicon-ferrite sheet for power-transformer cores, which is processed to develop a new optimum texture for high electrical efficiency. Yet it should be possible to find other examples, involving other kinds of properties. More specifically, there is good analytical reason to expect improved combined-stress yielding resistance in suitably textured material,2,3 and it has now been shown by experiment that texture hardening or softening is a potentially useful phenomenon in certain engineering devices and processes.'-I To date, work has included measurements of the transverse (width to thickness) strain ratios in the

Jan 1, 1967

By W. A. Johnson, F. N. Rhines, W. A. Anderson

The rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.' These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish- able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1942

By W. A. Anderson, F. N. Rhines, W. A. Johnson

The rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.' These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish- able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1942

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913

By A. C. Richardson

TROUGHS or launders are probably the oldest machines used for ore. concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean: coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four troughs placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratifica-tion. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and. fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder.

Jan 1, 1938

By L. H. Reiss, J. Groult, L. Montadert

Many fields, where the reservoir is composed of sandy layers, show great complexity because of the lack of continuity which results from a particular type of seditnentation. This complexity may be a factor of prime importance in studying reservoir drainage, especially in the displacement of oil by water or gas. This paper describes work done to study this heterogeneity and its influence in the exploitation of the fields of the lower Devonian sandy shale in the Fort Polignac Basin in Algeria. Two lines of research were followed. 1. On the border of the hasin, a detailed sedimentological study established rules for the distribution of the sandy zones, which furnished hypotheses necessary for devising a geologic model of the reservoir. A certain number of sandy zones were recognized and characterized by their sedimentation. 2. In the interior of the basin, production logs deterrnined the productivity profile. Study of these point data led to a description of the distribution of oil and gas phases in the reservoir so that the continuity of different zones between the wells could be deduced. These techniques were applied to the study of the lower Devonian sandy shale reservoir of Zarzaitine. The sedimentological study guiding the correlation work, with the aid of the conventional static data (logs and cores), led to the establishment of a useful geologic model of the reservoir. Production logs, thanks to the contribution of dynamic elements, permitted corrobora-tion of the model. In particular, the logs confirmed separation, as proposed by the sedimenfological study, of two comparable sandy groups by revealing the continuity of a thin impermeable layer, invisible on conventional logs. INTRODUCTION The heterogeneity of sandstone reservoirs considerably influences the distribution of fluids, as well as their displacement in the reservoir. Rational development of a field and maximum recovery of hydrocarbons are closely tied to an exact and precise knowledge of the intern architecture. We will try to show how it is possible I refine the knowledge of the reservoir by seeking qui different and varied sources of information. Productic geology, the group of techniques which leads to idei concerning reservoir architecture and its geometric descris tion, furnishes the framework of this undertaking. Of these techniques. those used so far are qui varied. Descriptive as well as quantitative, the technique partake as much of classical geology as of reservo science. They include (1) geologic studies of the enti basin, especially a stratigraphic and sedimentologic study of the reservoir member at its outcrop, detail1 observations of cores taken from wells and, finall oriented cores; (2) interpretation of geophysical dat (3) interpretation of electric logs, nuclear and sonic lo and dipmeters: (4) petrophysical study of the reserve on samples taken from wells; (5) reservoir dynamics (stu of the production history and, in particular, interpretati of production logs); and (6) analysis of the fluids a thermodynamic studies. This incomplete list could also include (1) study the migration of the fluids, (2) geochemistry (chemi characterization of the oils), (3) regional hydrodynamii and (4) injection and detection of tracers. If most of these techniques are classic, attention i nevertheless be called to applying two of the techniql in conjunction: the study of the reservoir member its outcrop and the study of dynamic distribution fluid phases in the reservoir through use of product logs, used in the study of the sandy shale reservoirs the lower Devonian of the Fort Polignac Basin, Alge in particular, their application to the study of the 2 zaitine field where they have led to a new and satisfact model of the reservoir will be described. THE ZARZAITlNE FIELD Situated in the interior of the Fort Polignac 8 about 150 kilometers (km) north of the lower Devol outcrop, the Zarzaitine Devonian oil field was discovc On Ian. 28, 19'' (Figs. 1 and l8). It is in the fern a monocline truncated by two perpendicular fault: great throw, with a downthrown section to the north\: Erosion at the top of the structure has caused one of it to disappear. It is a reservoir with a gas cap an m coefficient on the order of 1:5, open to the aql On the northeast, with the oil zone covering an Of 106 sq km and with initial oil reserves of 222 mi

Jan 1, 1967

By Arthur W. Rose

Statistical techniques are being widely used in geochemical exploration to answer questions involving sample spacing, analytical and sampling errors, thresholds, data smoothing, and optimum combination of several elements into one measure of favorability. The applications of sampling theory, mean and standard deviation, trend surfaces, moving averages, factor analysis, cluster analysis, discriminant analysis, and regression analysis to these questions are discussed with examples. Although the techniques are very useful as means of handling large amounts of data, they require as much geological and geochemical judgment as any other approach to data interpretation.

Jan 1, 1973

By Peter Kos

Since advances in the understanding of gravity thickening reflects the development of knowledge about suspensions themselves, the paper starts with the discussion of flocculent and nonflocculent suspensions. The properties of flocculent suspensions and their behavior in different concentration regions (zone settling, channelling, compression) are defined and discussed. In the main portion of the paper, the behavior of flocculent and nonflocculent suspensions during batch as well as continuous thickening, is presented, together with a brief review of the gravity thickening theories and sizing methods. The classical as well as the most recently developed methods are presented and their use and limitations are discussed.

Jan 1, 1980

By Delbert E. Gann, Richard D. Hagni

Ore microscopic study of copper-bearing shale at the Creta mine in southwestern Oklahoma reveals a variety of copper sulfide grains and shows that each has originated by replacement of original constituents In the Permian Flowerpot Shale at Creta. The largest grains, about 120 pm in diameter, are replacements of megaspores with triletes morphology. Their interiors are shown by Auger microprobe analyses to be organic matter. The interior organic matter and the spore exines have been replaced by anilite and djurleite. Digenite and anilite replace collomorphic pyrite averaging 40 pm in diameter. Grains 10 pm or less in d~ameter are mostly euhedral, six-sided, platy crystals that have anllite compositions and are pseudomorphous after pyrrhotzte. Other 10 pm copper sulfide grains are pseudomorphous after octahedra and cubes of pyrite. The results of this study indicate that the copper minerals are epigenetic and were deposited from fluids introduced into the Creta shale when it was relatively uncompacted and permeable. The shale served as a favorable reducing environment that contained a source of sulfur in the form of pyrite and pyrrhotite.

Jan 1, 1985

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By A. S. Yue, A. E. Vidoz, F. W. Crossman

Tensile specimens were prepared from a single grain of an epitaxially grown Al-CuAl2 eutectic ingot. The eutectic lanzellae were oriented parallel and perpendicular to the tensile axis of the specimens. Since the composite was of the eutectic composition, the aluminum-rich matrix could dissolve up lo 5. 7 wt pct Cu in solid solution and, therefore, was amenable to strengthening by precipitation hardening. The tensile properties of the eutectic single crystals were determined at room temperature as functions of interlamel-lar spacing, platelet orientation, and thermornechanical trealment. The obserced variations in composite stress and modulus with respect to the level of&apos; composite strain are discussed in terms of premature fracture of CuAlz platelets, a distribution function for the strength of the lamellae, and unequal strains due to localized fracture of&apos; platelets. The discontinuous fiber composite model of Kelly and Tyson is modgied to account for a changing distribution of fiber lengths during composite loading. The tensile properties at elevated temperatures were determined for the direc-tionally solidified eutectic oriented with platelets parallel to the tensile axis. The observed properties are attributed to the onset of plasticity of the CuAL2 phase above 150°C. DURING the investigation of whisker- and fiber-reinforced metallic matrix composites in recent years, two major problem areas have developed: 1) The fabrication of the composite involves tedious handling techniques in order to obtain a unidirection-ally aligned and uniformly spaced set of whiskers in the metal matrix. 2) Due to weak interfacial bond strengths or because of the formation of additional embrittling phases at the metal-fiber interface during long-time exposure or fabrication at elevated temperatures, many composite systems have exhibited considerably lower strengths than those predicted by a law of mixtures analysis.&apos; These problems have been bypassed by the technique of growing whiskers and plates of high-strength materials in a ductile metal matrix by controlled unidirectional eutectic solidification.2 The tensile properties of directionally solidified A1-CuA12 eutectic are presented here. This alloy consists of a ductile aluminum matrix, containing up to 5.7 wt pct Cu in solid solution, which is amenable to precipitation hardening by heat treatment and a reinforcing high modulus CuAlz intermetallic phase. The two phases are present in the form of alternating platelets or lamellae. The microstructural stability of this unidirectionally solidified alloy at elevated temperatures has been studied extensively.3.4 and preliminary tensile and bend tests have been reported. 5-7In the present investigation the tensile properties of the A1-CuA1, eutectic have been studied as a function of several ther-momechanical variables: solidification rate. heat treatment. rolling at elevated temperatures. and lamellar orientation. It was felt that the uniformity of structure and excellent interfacial bonding would give tensile properties concomitant with the metal matrix composite theory of strengthening proposed by Kelly and coson. 8-9 The tensile properties that were obtained point to a wide distribution of strengths for the CuAlZ platelets, which leads to large deviations from the predicted mechanical behavior for this composite. EXPERIMENTAL PROCEDURE Epitaxial Growth of Eutectic Alloy. The A1-CuA1, eutectic alloy was prepared by an epitaxial growth process. Sections of a master alloy ingot (total impurity content <0.008 pct) were placed in an alundum boat, melted. and directionally solidified to obtain a multigrained plate 12 by 2 by 4 in. This plate was tapered at one end to mate with a seed crystal 1; in. long and 4 by $ in. square. Then the seed-plate combination was placed in an alundum boat which sat in a quartz tube passing through the center of a horizontal resistance wound tube furnace. A dried argon atmosphere was maintained. The temperature gradient in the furnace was such that the liquid-solid interface of the eutectic alloy was located near the end of the furnace and could be observed through the quartz tube. Single-crystal plates were formed by melting the material back to the midpoint of the seed crystal of the desired platelet orientation and then epitaxially growing the plate from the seed by withdrawing the alundum boat from the furnace at a constant rate. This technique was used to produce aluminum and CuA12 lamellae parallel and perpendicular to the transverse direction on the plate. Metallographic examination showed that both phases were continuous across the original liquid-solid interface. It was also possible to grow a plate from two seeds placed side by side: and, although the lamellae of one seed were oriented at 90 deg to those of the second seed, the interface between the two grains remained parallel to the growth direction along the entire ingot length. Maintenance of a straight intergranular boundary during the solidification process was possible as long as both seeds were oriented with their original growth direction parallel to the solidification direction of the plate. Eutectic plates were directionally solidified at rates of 0.2, 1.0. and 4.7 cm per hr and sectioned transversely to the solidification direction to determine the apparent inter lamellar spacing of the lamellae. Metallographic examination was also employed

Jan 1, 1970

By Wilfred Walker

With the advent of the New Global Tectonics a coherent pattern of geology is emerging. To the economic geologist this is of vital concern because the type of mineralization in particular environments is predictable. Developments in geological reasoning now take their place beside developments in geochemistry and geophysics. Much is known of the worldwide geography of the Alpine orogenic period because it is now ending its 200 million years of existence, starting with the Jurassic, and we can see the mid-ocean rises and the down flow zones, and between them the stable oceanic and continental platforms. The concepts of mantle cells, the spreading sea floor, and continental drift have gained general acceptance. The oceanographers have demonstrated the uprises like that in the mid-Atlantic. In this paper it is suggested that down flows in the oceans are marked by island arcs, like the West Indies; and down flows in the continents are marked by orogens like the American Cordillera. The number and position of mantle cells is controversial: a total of about 16 cells is suggested in this paper. Certain cells expand, and as they carry continents with them give rise to concepts of plate tectonics. Specific types of mineral deposits are associated with the uprises, oceanic and continental platforms, and down flows. The uprises are accompanied by the currently described Red Sea and Salton Sea deposits, the oceanic parts of the platform have the nodular deposits, and the continental platforms have the post-tectonic deposits. However, most economic metal deposits are associated with the down flow zones in which the stage of geosynclinal development controls the type of deposit: (1) In the initial development stage the simatic upper mantle may be tapped and give rise to the volcanogenic massive base metal sulfide deposits and to the ophiolite suite which characteristically carries nickel, chrome, and cupreous pyrite. (2) In the early geosynclinal stage sialic crust is driven down into the simatic magma of the upper mantle and basic to acidic differentiates give rise to stocks accompanied by skarn and hydrothermal deposits. (3) The intermediate stage of geosynclinal development gives rise to tin-tungsten, lithium, and beryllium deposits as the magma chamber rises above the level of the upper mantle and there is no simatic component. (4) The late stage is one of regenerated deposits. The porphyry deposits are not restricted to stages but only by the time of generation of acid magma. As the geosynclinal system dies, the mantle is again the source of magma, giving rise to gabbro and diabase dykes and sills: in this last, post-tectonic, continental platform environment are found the Mississippi Valley type lead-zinc deposits, the Blind River and Witwatersrand type of sedimentary uranium and gold deposits, and also Sudbury&apos;s nickel. The key relationship of major ore deposits generated by downflows is depicted herein on a framework of uprises, platforms, and downflows in the Alpine orogenic period. There is evidence for nine orogenic periods, of which the Alpine period is the latest, having taken place from 3500 million years ago to the present. Each period was characterized by its own worldwide mantle cell system and associated uprises, platforms, and down flows. The cycle of geosynclinal development, including corresponding cycles of mineralization, can be precisely defined in relation to each of these orogenic periods. The development of the Alpine orogenic period therefore can be used as a guide to the study of the earlier orogenic periods which comprise well known periods: Kenoran, Hudsonian, Grenville, and Paleozoic; and less well known: Konkian, Aulian, Belomorian, and Elsonian [(Table 1)]. Each name is used for the period as a whole, and not for the main orogenic event.

Jan 1, 1973

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passageways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground. Rock bolting is now replacing timbering at an ever increasing rate. Experience has proved that this form of ground support is just as applicable to blocky igneous rock as to stratified rock. Besides preventing sloughing of the walls and back of underground openings, Fig. 1, rock bolting has a stabilizing effect on the surrounding ground in much the same manner that steel reinforcing rods add to the strength of concrete structures. Further, rock bolting is flexible and may be applied to any shaped excavation, whereas timber sets are in a fixed pattern and the ground must often be changed to conform with this pattern. Rock-bolting installations were made in metal mines of the Northwest as early as 1939. An exhaust air crosscut was driven that year in one of the Butte mines of the Anaconda Copper Mining Co. The crosscut was rock-bolted and gunited at the time it was driven and is still being used to exhaust hot humid air from the 3400 level of the Belmont mine. It is interesting to note that no sloughing or caving has taken place in the 14 years it has been open. Even though these early installations of rock bolts were successful, few men recognized their potentiality until recent years, when the coal mines started their programs of mechanization and the great trend toward roof bolting began. In some areas of the Northwest stopes that previously required heavy timbering and close backfilling are now being mined by the more economical cut-and-fill and shrinkage methods. When used in conjunction with timbering, rock bolting increases the efficiency of the operation by decreasing hanging wall dilution and by making it possible to blast larger rounds. Most of the rock bolts installed to date in mines of the Northwest have been the 1-in. diam slot and wedge type, but there has been a recent trend to- ward using the 3/4-in. diam expansion shell bolt shown in Fig. 2. In addition to these commercially manufactured steel bolts, wooden bolts have been used with considerable success by the Day Mines of Wall&apos;ace, Idaho. Installation of the slot and wedge type requires three distinct operations, with tools for each operation: 1—drilling the hole to proper diameter and depth, 2—setting the bolt, and 3—tightening the nut. Holes are drilled and bolts set with pneumatic rock drills. A number of setting or driving tools have been used successfully, but most follow the same general pattern. Usually the driving tool is designed to accommodate a short length of drill steel on one end and the rock bolt on the other end. In this manner the hammering effect of the rock drill is transmitted through the steel and driving tool to the bolt. When machines not having stop rotation are used, slippage is allowed between the driving tool and bolt or between the drill steel and driving tool. The rock bolt nuts are tightened either with pneumatic impact wrenches or with hand wrenches. Impact wrenches are desirable because they are faster and assure adequate tightness. Expansion shell bolts have the following advantages over slot and wedge rock bolts: 1—No special equipment other than a wrench is needed for their installation. 2—Installation is faster. 3—They are removable. 4—Holes need not be drilled to a specific depth as the expansion shell will anchor anywhere along the length of the hole. These advantages are offset somewhat by the lesser strength of the bolt, since expansion shell bolts are generally made from 3/4-in. diam steel as compared to 1-in. diam steel for the slot and wedge type. One manufacturer, however, is now fabricating expansion shell rock bolts from steel of high tensile strength, which gives this ¾-in. bolt a much greater strength than that of the mild steel bolt. Table I illustrates tests made by the Anaconda Copper Mining Co. to determine the proper hole size to use with various types of bolts and to determine

Jan 1, 1955

By N. H. Jensen, B. L. Sackett, Carlos Bardwell, Simon Jacobson

Lead smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was molded into bullets. With the development of the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 21/2 ft. in diameter, and smelted from 3 to 10 tons in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This procedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Furnace capacity was about 14 tons per day, with a campaign of about 16 days. Cost of smelting was about $44 per ton. The ores making the

Jan 1, 1926

By J. T. Norton, N. J. Grant, A. R. Chaudhuri

MOST of the recent work to establish the mech-anism of creep in metals at high temperatures has utilized aluminum as the experimental material. It was thought desirable to initiate an investigation of a hexagonal close-packed metal, because of the relatively simple slip system, and compare the observed deformation characteristics with those that have been observed for the face-centerd cubic metals. High-purity magnesium was chosen for this purpose, first, because its strength and other mechanical properties are similar to those of aluminum in the same temperature range, and second, because the existing equipment was ideally suited to observe magnesium during creep. It is proposed in this paper to present a pictorial and qualitative account of the changes that high-purity magnesium undergoes during creep at 500°F. The characteristics of deformation of aluminum described below have been observed by various workers and accounts of these may be obtained from the papers of Chang and Grant.&apos;- These characteristics are: slip, subgrain formation, grain boundary sliding and migration, fold formation, deformation bands, and kink bands. It is well known that in a flat magnesium specimen, slip on the basal plane (0001) in the [1120] direction results in the formation of straight bands on the surface of the specimen. Schmid and co-workers&apos; have shown that this system is operative in the temperature range of -185" to 300°C (-300° to 572°F). They have also shown that a second system, slip on the pyramidal planes {1071} or {1012} in the [1120] direction, is operative at temperatures higher than 225°C (437°F). Between 225° and 300°C (437" to 572°F), therefore, deformation by both these systems is expected. Bakarian and Mathewson5 confirmed the occurrence of pyramidal slip on the {1011} plane and found that it resulted in irregular markings on the surfaces of their specimens. Burke and Hibbard6 obtained evidence of pyramidal slip in single crystals of magnesium deformed at room temperature. Bakarian and Mathewson5 suggested that the irregular appearance of these bands was due to slip on both of the pyramidal planes occurring simultaneously but in the same direction, the close angular relationship between the planes making this process possible. Furthermore, since neither of these planes is close enough to the basal plane, slip on the latter does not exhibit the irregular appearance of slip bands resulting from pyramidal slip. Experimental Procedure High-purity magnesium, supplied by the Dow Chemical Co., was used in these experiments. The analysis was as follows: Al, 0.0002 pct; Mn, 0.0018; Fe, 0.0024; Cu, 0.0002; Sn, 0.001; Ca, 0.01; Ni, 0.0003; Zn, 0.01; Pb, 0.0005; Si, 0.001; and Mg, 99.972. The magnesium was supplied in the form of 1/2 in. diam rods. The specimens had an overall length of 21/4 in., the round ends being threaded to fit the specimen holders. The previously round 3/16 in. diam gage section of the specimen had two parallel flats machined on opposite sides for microscopic observation, yielding a test zone having the dimensions of lx3/16x7/64 in. The specimens were electrolytically polished (without prior mechanical polishing of the machined flats), in a solution composed of 375 ml of ortho-phosphoric acid and 625 ml of ethyl alcohol.&apos; The cathode was a stainless steel sheet bent so that the specimen was completely surrounded. The voltage for successful polishing was 1.5 v at 100 to 300 milli-amp current. Electropolishing for about 45 min sufficed to obtain a good metallographic surface on the specimens after they had been machined. The creep tests were performed under constant load, and two types of equipment were used. In the first, designed by Servi and Grant,V he specimens were beam-loaded, and a furnace could be lowered to surround the specimen. As the microstructural changes could not be observed during the course of the test, the tests had to be interrupted periodically by removing the specimen for microscopic examination. The second unit was a high temperature microscopy furnace designed by Chang and Grant.&apos; The furnace was fitted with an optically flat quartz window having area dimensions 1.25x0.5 in., so that the whole test portion could be viewed through it at magnifications up to x240. The metallurgical microscope had three mutually perpendicular axes of motion, and, in addition, it was possible to measure angular displacements by rotation of the eyepiece. It was thus possible to make precise observations of the specimen during creep, and micrographs could be taken by attaching a camera to the eyepiece of the microscope. The average grain size of the specimens that were tested was about 1 to 3 mm. This grain size could

Jan 1, 1954