Search Documents

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962

By Albert Hayes

FOUR mines at Wabana, on Bell Island in Concep-tion Bay, Newfoundland, produced 1,209,777 tons of ore in 1927, and it is expected that the produc-tion will be larger in 1928. The ore is a stratified oolitic hematite of sedimentary origin. Three workable beds and many thin beds occur in a thickness of 400 ft. of interbedded sandstones and shales. It is not profitable under present conditions to mine extensively in ore beds less than 4 ft. thick. The iron ore beds outcrop on the small island and are inclined northward more steeply, than the slope of the ocean bottom. The mine work-ings follow the bedded ore below the sea bottom, No. 3 Mine extending about 2 miles north of the island. At this point there is a cover of 1500 ft. of rock and 600 ft. of ocean water. It is impracticable to operate drills in the ocean to prove the extent of the submarine orebody in advance, and diamond drilling from the mine workings is the only method of exploration. Bell Island has been settled for a long time and a monument at Cupids, near Brigus at the head of Conception Bay, commemor-ates the tercentenary of a settlement there in 1611 by Captain Guy of England. was one of the chief ports of Newfoundland for deep sea fishing and doubtless many a captain wondered about the red rocks as he sailed past. The famous geologist, J. B. Jukes, records seeing a bright red sandstone 8 ft. thick on the northwest side of Bell Island during a visit in 1842, but he evident ly did not try to land on that rocky coast to get a sample. The iron ore is plainly visible in the high cliffs along the coast of the island, as bright brown layers interbedded with gray and white sandstones and dark shales. The heavy red rock was used by the fisher-men as anchor weights for fish nets and small boats, but its real value, so the story goes, was discovered by a merchant in Saint John,

Jan 8, 1928

By P. E. Fitzgerald

SOME readjustments in the research programs of most of the oil companics and petroleum engineering schools have been made necessary by the war. The most obvious change has been the conversion from production engineering to problems more closely related to the nation's was effort. Many laboratories now devote much of their time to studies on products to be derived from petroleum. such as synthetic rubber, toluene, and substitutes for critical materials. Others are working to improve motor fuels including high-octane gasoline and the special lubricants required by the wide geographical range of the present conflict. Of great importance is the experience of the geophysicists, who are now devoting a great percentage of their time on instrument research and production or special apparatus required by the armed forces.

Jan 1, 1943

By A.A. Grubb, F.L. Wolf

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By F. L. Wolf, A. A. Grubb

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By J. R. Long, T. R. Graham, R. S. Dean

FOLLOWING the development of elec¬trolytic manganese production by the Bureau of Mines, an extensive program was planned to study the character of this high-purity product and its possible utilization in various alloy combinations. Previous work reported in the literature concerning alloys containing substantial amounts of manganese dealt largely with material prepared from relatively impure grades of the metal, and in many instances the impurities thus introduced did not permit true evaluation of manganese as an alloying element. One phase of the Bureau's program included a general review of the system and the establishment of the physical properties of copper-manganese-zinc alloys, using electrolytic manganese, and with particular emphasis directed to com¬positions within the alpha solid solution area. A number of reports of the work on alloys in this system, giving specific data concerning the equilibrium system and some of its alloys, have already been published. One study1 established the alpha solid solution area at various temperature levels and composition ranges up to 50 pct manganese. Other investigation reports presented the properties of selected alloys; namely, a 65 pct copper, 10 pct manganese, 25 pct zinc alloys' a sensibly white manganese brass composed of 70 pct copper, 20 pct manganese, 10 pct zinc,3 and a series of alloys with a constant copper content of 60 pct and 5 to 25 pct manganese, balance zinc.4 In these reports tensile properties as influenced by cold-working and subsequent annealing were given in detail. Additional data are now available on other alloys of the alpha region up to 50 pct manganese, and these, together with previously published information, are sufficiently complete to establish the relationship between properties and composition for this portion of the ternary system. The present report is a summary of the tensile properties of wrought alloys in the form of sheet and rod stock. The summary is necessarily limited to data for only one condition of cold-work and a single annealing temperature, since a complete exposition of all the data available would be too extensive for this presentation. Nevertheless, it is possible to make a reasonable approximation of the tensile properties in other conditions of cold-working and annealing by a correlation of the data previously presented on specific alloys and the data given here.

Jan 1, 1947

By Herbert Haas

The following notes describe a laboratory for metallurgical chemistry and technical analysis which I built late in 1903, while engaged, as constructing engineer, in erecting a pyrite smelter at the Afterthought mine, Ingot, Shasta county, California. This design partly supplements the paper of Mr. C. H. White, which was presented at the Atlantic City Meeting of the Institute in February, 1904.' The work of a chemist at a busy smelting-plant differs radically from the work of a student, who takes all possible care to have his analysis exact within hundredths of a per cent., and has plenty of time to devote to the operation. The works-chemist, having the shortest time in which to make his determinations, should have a laboratory arranged as conveniently as possible to save time in carrying out his work. By a conveniently-arranged laboratory, I do not mean an elaborately furnished one; but rooms suitably fitted up and supplied with the necessary apparatus to do the work expected from the chemist within the requirements of technical analyses. It is not uncommon at large smelters to have the night ae-sayer prepare 30 or more samples for titration, in time for the

Jan 1, 1905

By W. D. B. Motter

DURING the early development of blasting with liquid oxygen explosives the trend of experimentation was towards increasing the effectiveness of the explosive. Its characteristic of becoming inert after evaporation of the oxygen content made a strong appeal from the standpoint of safety, especially with missed holes. It later became apparent, however, with practical use of this explosive, that LOX lacked certain other safety characteristics. As its effectiveness was increased, it became more subject to detonation by impact. The object of this paper is to show the steps taken by one operating company to achieve greater safety in the large-scale handling of liquid oxygen explosives.

Jan 1, 1933

By John A. Wolfe

The brightest spot in the mineral economy of the Philippines is the rapid development of reserves and production of copper. If economic conditions remain favorable and the political climate is encouraging, production of this metal should increase at a rate of 25% per year for several years, long enough to rank this country as one of the major copper producers of the world. In 1965 the copper content of the Philippine concentrates was approximately 60,000 tons. It should total about 80,000 tons in 1966. A major part of the increase will come from the rich Lepanto mine located in Mountain Province, North Central Luzon. Daily production of ore increased from 1200 to 2000 tons at the end of 1965. The ore, consisting of enargite and luzonite, averages nearly 3% copper and 0.12 oz. of gold per ton. It is an under- ground operation with a cutoff grade of 2%. The ore is associated with extensive silicification under a volcanic cap rock. Further expansion to increase ore production to 2600 tpd is under way.

Jan 4, 1967

By J. B. Warriner

Stripping is the name given to the process of removing clay, rock, or other cover from deposits of coal or ore. In this paper it is intended to cover the methods used in carrying on this operation in the anthracite coal regions of Pennsylvania. In doing this, attention will be chiefly devoted to those methods wherein practice in different sections of the region differs, or is susceptible to change or improvement, though it is intended to give as complete data as possible concerning all stages of the operation. The data from which this paper has been prepared have been collected and submitted by a committee† representing the larger users of stripping methods, of which committee the writer has acted as chairman. Data and assistance have also been obtained from various mining men, engineers, contractors and manufacturers of stripping equipment, to all of whom our appreciation is due. Early History and Statistics The earliest mining operation on a commercial scale in the anthracite region was a stripping operation. This was the famous Quarry mine at Summit Hill, where this method was used only because no other method of mining a deposit of the nature found there seemed feasible to the early operators. A description of this stripping from a report published in 1821 is as follows: "The coal mine at present worked by the company lies on the top of a mountain, and appears to extend over some hundred acres of land covered by about 12 ft,. of loose black dirt resembling moist gunpowder, which can be removed by cattle with scrapers, and thrown into the valley below so as never to impede the work. The thickness of the coal is not known, but a shaft has been sunk in it 35 ft. without penetrating through. More than an acre of mine has been uncovered and presents a huge rock of coal, which is easily quarried without blasting."

Jan 1, 1918

By C. A. Hansen

INTRODUCTION It has been the experience of the writer, during some. five years' work with electrolytic zinc, that the zinc cell is perhaps more- sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulphate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities. and cumulative impurities derived from the leaching of the ore; it also in

Jan 3, 1918

By N. J. Myers, S. J. Nemeth

POWER in the mill at Appalachian Sulphides Inc. is provided by 86 electrical motors ranging from 1 to 200 hp and totaling 1200 hp. After a careful study of different types of support for these cables an expanded metal trough was chosen as the most suitable. One hundred and twenty feet of trough were installed in 18-in. width and 150 ft in 6-in. width. This trough carries all the power as well as the control circuits. Now that the electrical distribution system is complete it is clear that this type of cable supporting system offers many advantages. To handle the same amount of cable in conduit, for example, would have required such a jungle that wiring all the different motors and controls would have been very difficult, even for the original hook-up. In the Appalachian Sulphides operation it has been necessary to make changes from time to time in the wiring of the different motors. These changes are readily made with the present cable supporting system because the trough leaves the wires accessible for rerouting as needed.

Jan 1, 1958

By H. W. Camp

ALTHOUGH the situation in the oil industry during the past year has. not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new products and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the anti-knock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gaso-line is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and com-petitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude, and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline' on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called "re-forming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature ,or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By Theodore Marvin

NOW that real progress is being made in building airplanes that can stand up under adverse conditions in isolated parts of the world, utilization of aviation by mining and petroleum companies is proceeding rapidly. This isolation, offering such handicaps to ordinary methods of transportation, also was the thorn in the flesh of aviation until the recent advances in plane and englue design. The accompanying illustration shows one of the six new planes just delivered to the U. S. Government for map making. The planes will be used in Department of Commerce, Coast and Geodetic Survey, Navy Hydrographic, and Insular work. There is a trap door in the bottom of the hull for a Fairchild camera which takes five pictures-vertical, N60°, E60°, S60°, and W60°-at regular intervals. It is manufactured by the Grumman Aircraft Engineering Corp., Farmingdale, N. Y.

Jan 1, 1935

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By Louis D. Huntoon

The Porcupine gold area, located on the Hudson Bay slope of northern Ontario, has produced over $100,000,000 in gold and has paid more than $28,000,000 in dividends, since the first real production in 1912. The character of the ore has been studied by the geologists of the Bureau of Mines of Ontario, the geological staffs of the operating mines, and engineers commissioned to examine properties there. What information the Government has is free to everybody; the geological staffs of the several properties also give to the visiting engineer what information regarding ore deposition they possess, and the author wishes to express his indebtedness to the geologists of the Ontario Bureau of Mines and the staffs of the operating mines for their free discussion of geological questions. This paper is based on the examination of several properties, various petrographic reports, not only on specimens from Porcupine but from elsewhere in northern Ontario, and interviews with Government and mine staff geologists. The petrographic work has been done by Prof. R. J. Colony, of Columbia University. Geological History The geological history of the district may be summarized as follows: The outpouring of great floods of lava accompanied by beds of tuff, flow following flow; the contacts of different flows can be seen in various parts of the camp. This period mas followed by an uplift and the production of the Temiskaming sediments by erosion. Later, dynamic action turned the sediments and underlying lavas on edge; this was followed by the intrusion of igneous rocks—in the Porcupine area the quartz porphyry, which is of such great importance in connection with the gold deposits. Doctor Burrows says: "The intrusions of quartz porphyry have in some way influenced the deposition or location of the gold but it is not likely the porphyry has been the source of the gold-bearing solutions." This statement of Doctor Burrows I indorse. The formation of non-gold bearing quartz veins followed the intrusion of the porphyry. These veins occur along or near the contact of

Jan 1, 1923

By T. A. Wilson

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.2 The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been clone on single-crystal zinc, but as it 'is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips3 have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1927

By C. W. Lawr

THE ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, are mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 lb.) KCN per ton of solution. As the daily discharge to. the dam was 1600 tons1 of slime of a 2: 1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and its recovery held alluring possibilities.

Jan 1, 1929

By Alfred E. Hunt

The late Alexander Holley said, on returning from a careful study of the relative merits of the Bessemer and the open-hearth processes, as shown in the best European practice, that, in this country, the open-hearth process would live to attend the funeral of the Bessemer ; and he said this several years ago, when in this country the Bessemer plant and practice had been developed to far outstrip that abroad, and when, proportionately, it had reached an advancement much beyond the improvements in open-hearth plants and practice. At the same time, the prevailing idea in the metallurgical world, a few years ago, seemed to be in favor of the substitution of Bessemer for open-hearth steel for most of the higher qualities, and Bessemer enthusiasts loudly proclaimed, that as good steel for all purposes could be obtained by their favorite process as by the open-hearth. It was, in fact, confidently prophesied that very soon tool-steel and similar grades, which consumers had learned to specify, in ordering, to be made by the crucible process, would by common consent be made by the Bessemer, as best adapted to give the desired results. But these expectations have failed to materialize; not only do the crucible people keep on in the even tenor of their way and talk with pride of their comparatively large outputs of " hundreds " of tons per month, as usual, but the open-hearth people have kept fast hold of their original domain of nearly the entire amount of sheared plates, of locomotive tires, of large forgings, spring-steel, agricultural steel, steel castings and the like. Further, owing largely to one of the great advantages of the Bessemer process, which is also one of its inherent dangers, namely, its large output, it has also fallen into considerable disrepute for structural purposes. Not a few experienced engineers are now stipulating in their specifications that Bessemer steel will not be allowed to be used, especially for tension-members.

Jan 1, 1888

By Atmaram H. Soni

A statistical study of machinability led the writer to examine existing data in regard to a thermal conductivity-mechanical properties relationship. Various functional relationships were proposed and the multiple correlation determined by statistical methods discussed in detail in the 1iterature.4 The relationship having the greatest engineering and statistical significance is discussed below. The data for cast and wrought aluminum alloys''2 have been compiled and analyzed separately. The results of these analyses are presented in Table I. The empirical equations for estimating the thermal conductivity (cal sec-' cm-I °C) are: for cast aluminum alloys K = 0.584 -0.00984/ -0.00263 Hb [1] and for wrought aluminum alloys K = 0.604 -0.00424l- 0.00170 Hb [2] where 1 and Hb are the percentage elongation and Brinell hardness number. Results of a similar analysis pertaining to stainless steel3 are also given in Table I. This empirical equation for estimating thermal conductivity (Btu per sq ft per hr per °F per in.) is K = 216.19- 1.716l - 0.0997 Hb [3] The relationship between electrical resistivity and mechanical properties was also examined for aluminum alloys using the same statistical method. These results are listed in Table II. While the situation of exact multiple correlation

Jan 1, 1965