Search Documents

By A. Ahmadieh, J. E. Dorn, Jack Mitchell

A detailed investigation of the disloccrtion mechanisms controlling prismatic, slip in a solid solutions of magnesium containing up to 15.9 at. pel Li revealed that low-temperature prismatic slip is controlled by the Peicrl's mechanism for all alloy compositions. At higher temperatures slip in the 7.9 at. pet Li alloy was found to follow the diclates of the cross-slip mechanism from basal to prism planes, while the higlier-lilhium alloys exhibited an athermal dejormation process which might be due COARSE-GRAINED polycrystalline aggregates of distilled magnesium exhibit very limited ductility at low temperatures.' The ductility of polycrystalline magnesium, however, is much improved by solid-solution additions in excess of about 8 at. pct to shot-range ordering. The major effect of lithium additions on the low-temperature Shear] stress. for prismatic slip appears to be due to its efftct in lowering the Peierl's stress whereas (1 increase in the shear stress with increased lithium conlent at higher temperatures might he due to short-range order strengthening. Additions rip to 7.9 (at. pel Li appear to have only minor effects on the slackiug-jaidt energy. Li.2 Although the relative amounts of basal slip and twinning are not materially altered by such alloying, a substantial change takes place in the relative amounts of prismatic slip. Whereas prismatic slip is negligible and limited to regions of high stress concentrations in the vicinity of the grain boundaries in pure magnesium, extensive prismatic slip over entire grains occurs in the higher lithium content alloys. Furthermore, as the lithium content is increased above 8 at. pct, the flow stress for polycrystalline aggregates decreases. Comparison of the single-crystal data on pure magnesium for basal slip by Sheely and Nash3 and those for prismatic slip by Flynn, Mote, and Dorn4 indicates that the critical resolved shear stress for prismatic slip is much above that for basal slip.

Jan 1, 1965

By H. F. Yancey, M. R. Geer

The importance of the size composition of coal is reflected in the difference in price of the various sizes of the same coal and in the large number of primary sizes and mixtures of sizes produced by the modern preparation plant to meet the demands of a market that in late years has grown increasingly conscious of coal size. The importance of size in the industrial and domestic uses of coal has its counterpart in the role played by size composition in the laboratory examination of coal. Investigation of many of the physical properties of coal in their relation to its uses requires an evaluation of size composition. In fact, the Standards on Coal and Coke issued by the American Socaiety for Testing Materials in 1936 contains 12 standard methods of testing that involve some use of size composition. The screen analysis is, of course, the standard method of determining size composition, whether the material is coarse run-of-mine coal or fine pulverized fuel. Custorriarily, the analysis is reported as the weight percentages retained on or passing each of a series of testing screens, the number of which may range from only two or three to as many as 20. When more than two or three sieves are used, which is usual, the number of weight percentages obtained is so great as to make the analysis difficult to comprehend. Direct comparison of analyses made 011 the same sieves is hard, and comparison of analyses covering the same range of sizes but made on different sieves is next to impossible. Consequently, a frequent purpose of sizing tests-—-correlation of size with properties and charactcristics related to size-—is rendered difficult. Less cumbersome means of expressing size composition have been attempted with various degrees of success. An average particle size, calculated by any of several formulas, is useful for some purposes, also the weight percentage retained on a single sieve finds some application as a

Jan 1, 1938

By M. R. Geer, H. F. Yancey

The importance of the size composition of coal is reflected in the difference in price of the various sizes of the same coal and in the large number of primary sizes and mixtures of sizes produced by the modern preparation plant to meet the demands of a market that in late years has grown increasingly conscious of coal size. The importance of size in the industrial and domestic uses of coal has its counterpart in the role played by size composition in the laboratory examination of coal. Investigation of many of the physical properties of coal in their relation to its uses requires an evaluation of size composition. In fact, the Standards on Coal and Coke issued by the American Socaiety for Testing Materials in 1936 contains 12 standard methods of testing that involve some use of size composition. The screen analysis is, of course, the standard method of determining size composition, whether the material is coarse run-of-mine coal or fine pulverized fuel. Custorriarily, the analysis is reported as the weight percentages retained on or passing each of a series of testing screens, the number of which may range from only two or three to as many as 20. When more than two or three sieves are used, which is usual, the number of weight percentages obtained is so great as to make the analysis difficult to comprehend. Direct comparison of analyses made 011 the same sieves is hard, and comparison of analyses covering the same range of sizes but made on different sieves is next to impossible. Consequently, a frequent purpose of sizing tests-—-correlation of size with properties and charactcristics related to size-—is rendered difficult. Less cumbersome means of expressing size composition have been attempted with various degrees of success. An average particle size, calculated by any of several formulas, is useful for some purposes, also the weight percentage retained on a single sieve finds some application as a

Jan 1, 1938

By Oliver Bowles

DELICATE PLANTS are now put to bed for the winter under glass-wool or rock-wool blankets. Thus arise new and unexpected uses for non-metallic materials and rocks and, at the same time, certain unique uses are fading out; for instance, the Italians have taken steps to bar the use of salt for money in Ethiopia. Novel sources of supply find a place in the record of recent achievements as exemplified in the migration of the frontiers of industrial mineral exploitation beyond the land area of the earth to include the ocean. Salt, of course, has been recovered from the sea for years but the treatment of enormous quantities of sea water for bromine has lately added to the importance of the ocean as a reservoir of mineral wealth. Increased use of non-metallic minerals in the commercial and economic life of the country is reflected in the wide scope and activity of the Industrial Minerals Division of the Institute. The outstanding recent achievement of the Division is the publication of a 955-page volume on industrial minerals and rocks, comprising 48 commodity chapters each written by an authority on the subject.

Jan 1, 1938

By R. G. Aspden

Crystals with an (001) [loo] initial orientation of an iron-base alloy containing 3 pct Si were cold rolled with and without the use of constraints. A major difference in the rolling and annealing textures was observed between crystals rolled with and without constraints. These data show that the contribution of constraints at grain boundaries in a poly crystalline sheet should be considered in applying textural data on single crystals to grains in an aggregate. SILICON-iron alloys with a cube texture have been recently developed and their magnetic characteristics reported.1-4 Of interest in the development of this texture were the textural changes of single crystals accompanying rolling and annealing and the influence of constraints at grain boundaries in an aggregate on the behavior of individual grains. The present study was primarily concerned with the effect of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001)[100]. Barrett and Levenson5 were among the first to observe an influence of constraints at grain boundaries on the textural changes of individual grains during deformation. They tested Taylor's6 theory of plastic deformation of face-centered-cubic metals in which deformation textures were predicted. About one-third of the grains in poly crystalline aluminum did not rotate as predicted. Grains of the same initial orientation were observed to rotate in different directions under the influence of applied stress and anisotropic flow of neighboring grains. Recently, the various inhomogeneities of flow of crystals in an aggregate have been studied7'8 and reviewed.9-11 Barrett and Levenson" rolled (001) [loo] iron single crystals inserted in close-fitting holes in copper to limit lateral flow and to simulate rolling of grains in an aggregate. Deformation bands were formed after a 90 pct reduction in thickness, and the cold-rolling texture contained two components described by rotating the (001)[100] about 35 deg in both directions around the normal of the rolling plane. No annealing textures were reported. Chen and Maddin13 rolled molybdenum single crystals initially (001) [loo]. The crystals were mounted between two hardened silicon-iron plates and 96 pct reduced in thickness by rolling at a low rate of reduction, about 0.0001 in. per pass. The deformation texture had the mean orientation of (001) [loo], and the azimuthal spread included orientations described by rotating (001) [loo] about 35 deg in both directions about the pole of the rolling plane. The presence of deformation bands were not reported by Chen and Maddin or detected in subsequent work of Ujiiye and Maddin.14 The ideal orientation of the annealing texture was (001) [loo]. Recently, Walter and Hibbard 15 reported on the textures of 3 pct Si-Fe alloy crystals initially near (001) [loo]. Each crystal was in an aggregate cut from a columnar ingot. After 66 pct reduction by rolling, the texture consisted of two symmetrical components which had the orientations described by rotating (001) [loo] about 30 deg in both directions about the pole of the rolling plane. Annealing texture was near (001) [loo]. In the above work, the textures of body-centered-cubic crystals were studied after rolling under the influence of constraints. The deformation textures varied from (001) [loo] to near the (001) [110] type and appeared sensitive to the manner in which the crystals were rolled. No textural data were available on the effect of rolling (001) [loo] crystals with and without constraints. The purpose of the present work was to evaluate the influence of constraints during rolling on the textures of 3 pct Si-Fe crystals initially (001) [loo]. Rolling and annealing textures were studied for a) crystals rolled with no constraints at different rates of reduction, and b) crystals rolled with constraints imposed by neighboring grains and by plates between which a crystal was "sandwiched". PROCEDURES AND EXPERIMENTAL TECHNIQUES Data are presented on four crystals which are representative of several crystals studied. The orientation of each crystal prior to rolling was (001) [loo] as determined by the Laue X-ray back-reflection method," i.e., each crystal had an (001) within 3 deg of the rolling plane and [100] within 3 deg of the rolling direction. These crystals were obtained from two iron-base alloys containing 3 pct Si by weight which were prepared by vacuum melting electrolytic iron and a commercial grade of silicon. Crystals 1, 2, and S-1 were cut from a large single crystal grown from the melt of one alloy by the Bridgman technique17 in an apparatus described by

Jan 1, 1960

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known out crops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The Oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this coal can be used in steel production is will be possible for the Mexican steel industry to reach new dimensions, commensurate with the growing industry of the central region. Coal can be utilized in thermoelectric plants in this area, which lacks not only petroleum and natural gas but also electric power. It can be used as domestic fuel, replacing charcoal and firewood.

Jan 5, 1954

Discussion of the paper of E. C. HARDER, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2573 to 2586. I. C. WHITE, Morgantown, W. Va.-I have seen some of the great iron-ore deposits described in this paper. -One of these in the State of Minas Geraes appears to be an immense mountain of iron ore about 2,000 ft. in height. All over its surface from bottom to top may be seen large masses of rich iron ore, varying in weight from a few pounds to several tons, and from all that one can judge without exploitation, the quantity of available ore is certainly very large in this particular mountain. Whether it will prove a mere surface deposit or shell, like the famous Iron Mountain of Missouri, is for future exploration to determine. The question of transportation is the main factor in determining the availability for exportation of these Brazilian iron ores. There is no coal in Brazil that can be manufactured into coke without expensive previous treatment, since the best of the raw coal in the States of Rio Grande do Sul, Santa Catharina, and Parana, contains about 35 per cent. of ash, of which about 6 per cent. is sulphur, and coal of this composition cannot be utilized in iron smelting without purification. When I was chief of the Brazilian Coal Commission in 1904 to 1906, I had a cargo of this coal shipped to Balk, Germany, and treated in the great coal-testing plant of the Humboldt Engineering Works, located just across the Rhine from Cologne. It was found that by crushing and washing the Brazilian coal, it yielded 33 per cent. of briquetting coal, containing only 10 to 12 per cent. of ash (of which 1 per cent. was sulphur), and 42 per cent. of slack coal, with 25 per cent. of ash and low in sulphur, so that about 33 per cent. of the Brazilian coal could be converted into coke of fair quality, as shown by the following average of three analyses, using air-dried coal, of briquets made from the Barro Branco coal bed, State of Santa Catharina: Moisture 1.56 Volatile matter 31.66 Fixed carbon 56.73 Ash : 10.05 Total 100.00 Sulphur 1.34 Phosphorus 0.003 B.t.u 13,395

Jan 4, 1915

By W. W. Cotter, W. R. Clark

WEBSTER tells us the word "extrude" means to "force, press or push out; to protrude." As applied to the metal industry, the process consists largely of forcing plastic elements (plasticity usually obtained by preheating), through dies of predetermined profiles, into constant sections of considerable length and weight. Most of the "virgin" metals are quite malleable under this process, likewise many of the commonly used "alloys" in various industries, when basic elements are proportioned or combined within the natural laws and limits of good metallurgy. Several of the foundry alloys, both ferrous and nonferrous, together with some of the heat-treatable light metal mixtures, are decidedly weak and hot short at ordinarily plastic ranges, and consequently are troublesome or quite incapable of commercial extrusion. DEVELOPMENT OF PROCESS This process was conceived some time before 1800 and during its first century was employed almost entirely in making lead pipe, plumbing fittings and coating electrical cables. As a result of contact and experience with the lead industry and presses, Alexander Dick, of London, England, is credited with first having applied the principles of extrusion to brass, and in 1894 brought out a 500-ton horizontal press powered by hydraulics. A duplicate of this unit was imported by one of the Connecticut brass mills and was in experimental operation by 1900. During the first five years of operation, this press proved the value of the method to American industry, as it immediately revolutionized and converted the manufacture of brass rod from a 15-pass cold-rolling operation, with elimination of several intermediate anneals and cleanings, to an extrusion and a finishing draw. Likewise, ornamental brass and bronze moldings formerly cast and machined were produced in one squeeze on the extruder. The extrusion operation, being entirely that of compression, deforms the material without tensile stresses and can be used on delicate mixtures under heat, which cannot be hot-worked by straight hot-rolling or roller piercing. Base slabs of clock-brass strip were early in line of development or improvement, as were the brass bronzes (Naval brass, Muntz metal, manganese bronze, and others), popular as engineering materials for bolt stock, as well as structural shapes for marine and other mild conditions of corrosion. By 1910, American engineers undertook to design tube shell extruders, but were unsuccessful. The first World War began before fabricators could procure the more substantial designs of tube extruders produced in Germany; and it was not until the middle twenties that better models of the Universal extruders (double-actioned presses), equipped with hydropneumatic accumulator systems and other modern equipment, were available in the United States.

Jan 1, 1945

By R. W. Gurry

THERMODYNAMIC calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a. better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganeie, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B203 in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1943

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

By Luther Wagoner

For a number of years I have, at odd times, tried to perfect a method of assay sufficiently delicate to find and estimate minute quantities of gold and silver. The object in view was to examine rocks remote from veins or mineral areas, in order to test the probability of the lateral-secretion theory. Having succeeded in measuring approximately the amount of gold and silver contained in one cubic centimeter of sea-water, I present a detailed account of the method employed, with some of the results obtained. General Method of Assay. The use of purified lead without other flux, blowpipe methods, extraction by cyanide, and measurement of the beads by the microscope. Purged Lead. The method of testing is by cupellation. On a properly prepared cupel, it is easy to cupel and find a bead of 0.002 mm. diameter. Such a bead of silver weighs about 1 part of a milligramme. A bead 0.02 mm. in diameter weighs about 1/24,000 mg., and a close approximation can be made to its weight. It is desirable that the lead used in the assay should be low in silver so as to avoid large correction, but as the parted

Jan 1, 1902

By D. Swan

Industrial research may be defined as a critical and exhaustive investigation to create new and better ways of doing things. The results of industrial research are new and improved products, processes, and techniques. This broad definition, of course, covers investigation of all subjects by either individuals or groups of people, and this chapter aims to examine the purpose (what research tries to do), and methods (or how research is done) as applied in the mineral industries. Concepts and History The idea or concept of organized research probably originated in the universities of Europe. There, groups of scholars banded together for discussion and application of their particular specialty to a common problem. Publication of the conclusions drawn from such investigations gave scholars in other areas the opportunity to review and criticize the work of their colleagues, and one of the hallmarks of scientific research work is the publication and criticism of the results of the investigation. It was not until the late nineteenth century that the concept of organized research for the profit of industry was recognized. During the late nineteenth and early twentieth centuries, a large number of industrial enterprises sponsored organizations to study the application of the physical sciences with the aim of making discoveries that would result in profit to the sponsoring organization. The tangible benefits accruing from these activities were so great that they, in turn, fostered several other methods for the support of organized research activities. For the large problems involving public interest, United States Government scientific research laboratories were set up. As the demand of smaller enterprises for research activities increased, research institutes and consulting laboratories were organized. In Europe the idea of common industry sponsorship of research centers grew and many large research organizations there were sponsored by associations of manufacturers. Finally, in the United States

Jan 1, 1964

By R. H. Doremus

From measurements of carbide precipitation rates in a iron it was concluded that the carbides nucleated on dislocations in both strained and unstrained samples, except for the latter at lower temperatures and higher carbon concentrations, where there were more muclei than could form on the dislocations. The equation of Cottrell and Bilby for the segregation of atoms to dislocations was found to be inapplicable to this system. No satisfactory theory for the growth process is available. A study of the rate at which a second phase separates from solid solution can frequently reveal much about the mechanism of separation. There are still many features of the precipitation of carbon from a iron that are not understood, although this system has been examined extensively. To provide more insight into the mechanism of carbide precipitation in a iron, rates of this process were measured at different temperatures, carbon concentrations, and densities of dislocations in the iron. The concentra- tion of carbon in solution was followed from the height of the internal-friction peak; this height is directly proportional to the amount of carbon in solution and is not affected by the growing carbide particles. In this paper these rates are compared with those found by earlier investigators, and the mechanism of precipitation is discussed in light of these results as well as two earlier studies1, 2 and the electron microscopic work reported in the preceding paper. EXPERIMENTAL The amount of carbon in solution was followed by

Jan 1, 1961

"For many years it has been known that large bodies of iron ore existed in Iron and Washington counties in Utah. The ore is chiefly hematite—both hard and soft—though some magnetite is found. No definite and complete estimate of the iron ore reserves of the state have been made. The U. S. Geological Survey estimated that 40,000,000 tons of ore were disclosed by development work averaging only 35 feet below the surface of the ore. The ore is found along an area about one and a half miles wide by twenty miles long, and for the most part on the eastern and southern slopes or foothills of Three Peaks, Granite Mountain and Iron Mountain. Later estimates by others have gone as high as ore in sight 164,000,000 tons, probable ore 300,000,000 tons and possible ore 1,000,000,000 tons. Whether this last estimate is too great or not there is sufficient iron ore in Utah to justify the starting of an iron industry.Two companies are now mining iron ore in Utah, the Columbia Steel Corporation and the Utah Iron Corporation. The mine of the Columbia Steel Corporation is at Iron Springs a few miles west of Cedar City. About 650 tons, of ore a day is being shipped to the blast furnace at Ironton. The ore is mined by the glory hole method. After being drilled it is blasted to the bottom of the several glory holes and is dropped through chutes into cars on the ore haulage level below. It is then hauled by electric locomotives to the crushing plant, where it is crushed to blast furnace size before going to storage bins. Some of the softer ore is brought to the chutes by Fresno scrapers."

Jan 1, 1925

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore ex- ploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composi- tion laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, varia- tions are functions of distance. Hence, in either case, variations along the hole are of greater effect than across it.

Jan 1, 1949

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By Lachlan Gilchrist

MEASUREMENTS of resistivity by methods involving the use of two current electrodes and two potential electrodes in general collinear with the current electrodes have been made extensively in geophysical investigations. In the method developed by Wenner and made use of by Gish and Rooney, and later in a modified form by Lee, the distance between the current electrodes is divided into three equal parts by the potential electrodes. In one of the methods developed by Schlumberger prospecting methods and by Koenigsberger, one current electrode is placed at considerable distance from the other and potential measurements are made in the immediate neighborhood of one of the current electrodes. The method is described as the single current electrode method, and the effect of the distant current electrode is considered negligible or a correction is made for the effect in the calculation of the resistivity. Usually the correction that is introduced is based on the calculated effect for measurements made in a homogeneous conducting material. The useful application of these methods in prospecting for minerals, of course, is in regions where nonhomogeneous conditions exist. In many of these conditions it is very doubtful whether the effect of the distant current electrode may be neglected, except for measurements in the immediate neighborhood of the "single" current electrode, and corrections based on homogeneity of the medium will necessarily be inadequate. In order to obtain a degree of symmetry that would preclude the necessity for corrections for the distant electrode and that would simplify interpretation, it appeared desirable to use a central current electrode and a set of distant end current electrodes symmetrically placed about the central electrode as shown in Fig. 1 and to provide by means of auxiliary resistances that the currents passing into the earth at the distant end electrodes should be equal. Circumstances did not permit the operation of this plan in complete detail but a degree of symmetry was obtained by using a central current electrode and two distant collinear end current electrodes and by taking measurements along a line passing through

Jan 1, 1931

By L. R. Duncan, O. M. Wicken

Magnesium, the eighth most abundant element in the earth's crust, is found widely distributed in a variety of minerals. Among the more commercially important ones are magnesite (MgCO,), brucite (Mg[OH],) , dolomite (CaMg[CO,],), and the salts magnesium sulfate and chloride often found in natural brines. Among other commercially important magnesium-containing minerals are olivine ([MgFe],- SiO,) , talc (H,Mg,[SiO,],) , and serpentine (H,Mg,Si,O,) . These are valuable because of desirable characteristics given them by the magnesium content and its placement in the particular crystal structure. These minerals are the raw materials for a host of products including magnesium metal and several grades of magnesia or magnesia- containing materials for refractories, fluxes, fillers, insulation, cements, decolorants, fertilizers, and chemicals. Considering only those minerals valued for their magnesia or magnesium content, over 85% of the material tonnages are processed to be used as refractories. Dolomite, which is used in enormous tonnages for its physical properties in construction, has an important use as a refractory raw material in its own right and, after calcination, as a precipitant for magnesium hydroxide, which is an intermediate for the production of magnesia or magnesium metal. Magnesia from the reaction of calcined dolomite (or limestone) with sea-water or magnesium-containing brines has supplanted much of the production of magnesia from mined magnesite, particularly in the United States. The best known of the minerals directly and widely exploited for magnesia content is magnesite, one of the calcite group of rhombo- hedral carbonates which includes calcite (Ca- CO,) , siderite (FeCO,) , and rhodocrosite (MnCO,) among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence, magnesite and siderite form a complete series of which breunnerite (ferroan magnesite) is a well-known end member. However, the radius of calcium ion is 36% larger than that of magnesium ion, and only limited substitution exists at each end of the MgC0,-Cam, series. Dolomite is not a member of the calcite group, but results when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of these relationships is that calcite and dolomite, often found intermixed with magnesite, occur commonly as identifiable crystal entities which can often be separated to a varying degree from the magnesite by various beneficiation techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO,. The pure mineral is sometimes, but rarely, found as transparent crystals resembling calcite, but, preponderantly, magnesite contains variable amounts of the carbonates, oxides, and silicates of iron, calcium, manganese, and aluminum. Magnesite may be either crystalline or "amorphous" (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black with shades of yellqw, blue, red, or gray. The color is not a fundamentally significant indicator of purity, but in a given deposit, an experienced person can often roughly grade magnesite by assessing color and crystallinity. The crystalline form of magnesite occurs in

Jan 1, 1975