Search Documents

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electrochemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are modified in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.'-a In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative and may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole. These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in Pennsylvania, carried out by the Pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, in the published literature. The potential differences across the contacts of sandstone and shale are called in this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored Well In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored with diamond tools. The potentials were first measured with fresh water in the hole. A null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and crystals surrounding a pure copper elec-

Jan 1, 1944

By E. E. White

I disagree with Mr. Brinsmade on serveral points, and I will discuss this remards under the same six topics which he has used.

Jan 1, 1915

By J. W. Littleford

The Roan Antelope Copper Mines Ltd. are situated in the north central part of Northern Rhodesia, at an altitude of 4000 ft. and 13" south of the Equator. The town site (Luanshya) is well situated and enjoys among other things a really temperate climate for 10 months of the year. The two spring and summer months, October and November, while hot and humid, do not bring any great discomforts as compared with many other mining camps. Strictly modern brick homes, with electric lights, purified water, telephone and water-borne sewage, add to the comfort of the employees. A rainfall of approximately 60 in. per year furnishes ample water for both industrial and domestic purposes. The rainy season generally begins in October and lasts through until March. As much as 3 to 4 in. is recorded in 24 hr., but this offers no difficulties because the runoff is very rapid. The property is connected by a 24-mile branch line from Ndola with the main line of the Beira-Mashonaland and Rhodesia Railways Ltd. Practically all supplies from overseas are transported over this line from Beira, 1743 miles distant on the east coast in Portuguese East Africa. The mine output also leaves Africa from this port. Passenger service is principally via Cape Town or Durban, a distance of about 2100 miles to either port. The Imperial Airways maintain a service from Cape Town to Croydon, taking 9 days for the trip. Connections can be made with this service at Broken Hill, 150 miles south of Luanshya, by either rail or automobile. Thus, after several days of travel through virgin bush, a visitor arrives at a typically modern town site in the heart of Africa. Every development in mining, milling and smelting practice is used to advantage. Plan of Mill The practice in the three principal phases of the production of copper from the ores of this company have been published from time to time. Milling practice, however, is continually changing and what may be

Jan 1, 1935

By R. G. Brown

Tars paper will present a general description of the different mineral belts in the Butte City region (limited, however, to the copper and contiguous silver veins) such as may serve to give an intelligent idea of the distribution and characteristics of the deposits, forming thus a groundwork of information, which it is hoped will have value, when later writers enter into particularized detail.

Jan 1, 1895

By Edward C. Morse

The metallurgical history of Republic has been completely reviewed in a paper presented at a previous meeting of the Spokane Local Section by Professor Thomson;' therefore, the present paper will be confined to matters directly pertaining to the San Poil mill: When I came to Republic last fall to look over the situation there was a plant in operation successfully treating the tailings from one of the earlier mills in the camp. I refer to the mill of the Rathfon Reduction Co. This mill was operating in accordance with modern cyaniding practice, and I was given to understand that the work was very satisfactory and profitable, else it would not have been continued as long as it was. At that time I obtained much metallurgical information of value from Harry W. Newton, Superintendent of the mill of the North Washington Power & Reduction Co. I took a number of samples from the San Poil mine, with the view of determining if Mr. Newton's experience with the ores from the other mines applied to the San Poil ores. I made a large number of tests under a variety of conditions, and found that it was possible to extract as high as 98 per cent, of the values from San Poil ore by the laboratory-tests when the ore was pulverized to 200-mesh and treated with a solution of a strength of 5 Ib. of KCN to the ton. A fairly strong solution was required because of the proportion of silver in the ore, which makes it, from a metallurgical point of view, practically

Jan 1, 1913

IF you do not make the disc at the same time as the core and as part of it, it is necessary to make it by itself. This is done by spreading on a board or other flat surface a layer of clay as thick and wide as [88] the disc that you made at the feeding head of the first pattern of the gun. When it is dry, mark it exactly with compasses and then, cutting with a chisel or rasp, make it fit exactly into the empty space at the head. Likewise, make a hole just as wide as the thickness of the core exactly in the middle of this clay disc. When you have put the disc in its place in the mould and then pass the core through this hole, it passes exactly through the center of the mould in such a way that it meets the iron ring that you put at the foot of the mould for this purpose. As I said above, if' you do not make it as part of the core, it is necessary to proceed in the aforesaid way. But if' you wish to make it attached to the core (which I like better because it can be done more accurately) make a

Jan 1, 1942

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method.

Jan 8, 1950

By D. Silverman, A. R. Brown

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the 'Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By A. R. Brown, D. Silverman

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the 'Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By A. Satter, J. M. Campbell

Reported herein are the results of a careful and detailed study of the non-ideal behavior of pure gases and their mixtures. Included are: (1) new data on five ternary systems composed of methane, ethane and H2 S; (2) a simple compressibility factor correlation that is inherently superior to present correlations, particularly for gases containing H2S and CO2; and(3) a detailed study of combination rules and the effect of system composition on the choice thereof. This study makes use of the rather large mass of data already available in the literature. A complete re-examination of the data and ideas presented in the last 25 years was considered desirable as a prelude to our basic concern — the effect of diluents on gas behavior. A consideration of both the macroscopic and microscopic properties of gases provides a better insight which, in turn, gives a firmer basis for improved correlation techniques. Such a study has shown that expressing the compressibility factor Z as a function of acentric factor w, as well as reduced temperature and pressure, yields a correlation that is broader in scope. The study of various combination rules has shown that better results are obtained by "tailoring" the rule used to the system composition. To do so improves the basic reality of results by overcoming some of the anomalies often found when using Kay's rule alone. Tentative recommendations are made regarding the most reliable combination rule for use with a given class of gas. The data presented are useful for estimating the direction and magnitude of the expected deviation when using a given rule. Although more work is needed, particularly around the critical region and with CO2 mixtures, the advantage of the classification scheme proposed is apparent. INTRODUCTION When one attempts to write a PVT equation to fit the data for actual gases, greater precision is obtained by the use of a multiple number of empirical constants. This has lead to multiple-constant equations such as Benedict-Webb-Rubin, Beattie-Bridgman, Keyes, etc., which are capable of yielding very precise results for pure gases in a range for which data to get the constants are available. As a matter of practicality, though, the use of such equations for gas mixtures is limited. Because of the infinite number of gas analyses available, any attempt to compile the constants needed requires a prohibitive amount of experimental data. This could be overcome by the use of a combination rule, but there is no real advantage in doing so because the end result offers no practical impovement over the Z factor correlation. The most widely used method of predicting the volumetric properties of pure gases is based upon the "theorem of corresponding states". According to this theorem, "all pure substances have corresponding molal volume at corresponding temperature and pressure if the reference point of correspondence is the critical point". Generalized compressibility charts for gases were prepared first by Cope and associates1 in 1931 and later by Brown and co-workers2 in 1932. However, the most commonly used charts are those of Dodge,3 Nelson and Obert,4 Hougen and atsson: and Standing and Katz.6 The work of Katz and co-workers has provided us with basic data for the hydrocarbons most widely used today. Their original chart6 was compared with a relatively large amount of multi-component data for gases consisting almost entirely of normal paraffin hydrocarbons. A deviation of only + 1.2 per cent was obtained.39 In the 20 years following publication of this work it has been found that the behavior of most mixtures of paraffin hydrocarbons could be predicted by this correlation within at least 5 per cent. Where difficulty has been encountered it has largely involved one or more of the following circumstances: pressures above 4,000 psig, mixtures containing large amounts of heavy ends and/or aromatics, systems in the critical region and mixtures containing polar compounds and/or CO2. The abnormal error sometimes found with such gases, not too unexpected for this method, is

By John H. G. Monypenny

The range of chromium content of stainless steel is, in most cases, included in the limits 11 to 14 per cent., or the middle part of the range, 9 to 16 per cent., specified by the discoverer. For some time after the steel was produced commercially, the carbon content was about 0.3 to 0.4 per cent. and occasionally higher; only rarely was material with 0.25 per cent. carbon or less produced. The reason for this is obvious from the nature of the alloys of chromium available for making such steels; as the lowest carbon content generally available was about 1 per cent., and this in conjunction with a chromium content of about 60 per cent., the production of a 12-per cent. chromium steel with less than 0.25 to 0.30 per cent. carbon was impossible. The advent, on a reasonable commercial scale, of carbonless ferrochromium has modified this condition, however, so that for the last three years stainless material containing 0.1 per cent. or less carbon and the normal amount of chromium has been on the market. As far as the author is aware, the material was first made on a commercial scale by the firm with which he is associated in June, 1920, when a 5- or 6-ton cast of material containing 0.07 per cent. carbon and 11.7 per cent. chromium was made and cast into 12-in. ingots. The necessity for using a totally different raw material, carbonless ferrochromium, instead of the ordinary low-carbon ferro (0.6 to 1.0 per cent. carbon) has led to the idea that stainless iron is a quite distinct product and quite different from stainless steel. While this may be true from a commercial aspect, it is wrong metallurgically. The name stainless iron is unfortunate as the material is a very mild stainless steel and forms the lowest carbon member of a series of steels of continuously varying content which are, in many respccts, the counterpart of the series of ordinary carbon steels ranging from "dead soft" to tool steels. In an article on stainless steel in the Journal of the Society of Chemical Industry, November, 1920, the author said "Just as in the far-off days 'steel' was regarded as a hard product of iron, and little or no attempt was made to grade it into harder or softer varieties, so at present stainless

Jan 1, 1924

By John H. G. Monypenny

The range of chromium content of stainless steel is, in most cases, included in the limits 11 to 14 per cent., or the middle part of the range, 9 to 16 per cent., specified by the discoverer. For some time after the steel was produced commercially, the carbon content was about 0.3 to 0.4 per cent. and occasionally higher; only rarely was material with 0.25 per cent. carbon or less produced. The reason for this is obvious from the nature of the alloys of chromium available for making such steels; as the lowest carbon content generally available was about 1 per cent., and this in conjunction with a chromium content of about 60 per cent., the production of a 12-per cent. chromium steel with less than 0.25 to 0.30 per cent. carbon was impossible. The advent, on a reasonable commercial scale, of carbonless ferrochromium has modified this condition, however, so that for the last three years stainless material containing 0.1 per cent. or less carbon and the normal amount of chromium has been on the market. As far as the author is aware, the material was first made on a commercial scale by the firm with which he is associated in June, 1920, when a 5- or 6-ton cast of material containing 0.07 per cent. carbon and 11.7 per cent. chromium was made and cast into 12-in. ingots. The necessity for using a totally different raw material, carbonless ferrochromium, instead of the ordinary low-carbon ferro (0.6 to 1.0 per cent. carbon) has led to the idea that stainless iron is a quite distinct product and quite different from stainless steel. While this may be true from a commercial aspect, it is wrong metallurgically. The name stainless iron is unfortunate as the material is a very mild stainless steel and forms the lowest carbon member of a series of steels of continuously varying content which are, in many respccts, the counterpart of the series of ordinary carbon steels ranging from "dead soft" to tool steels. In an article on stainless steel in the Journal of the Society of Chemical Industry, November, 1920, the author said "Just as in the far-off days 'steel' was regarded as a hard product of iron, and little or no attempt was made to grade it into harder or softer varieties, so at present stainless

Jan 1, 1924

By T. S. Washburn

Deoxidation is one of the most complex metallurgical operations in the basic open-hearth process. The necessity for deoxidation arises from the fact that the refining operations that precede it require the oxidation of the steel bath. when the refining is completed and the desired composition of the bath has been obtained with respect to the elements subject to control by 'oxidation. there is usually an excess of oxygen present in the bath from the standpoint of the amount desired in the finished steel. The objectives of deoxidation are to control the amount and type of oxides and, although not directly ilnp1it.d by the term or always considered as a Part of the process, to control the amounts of gases such as hydrogen or nitrogen that will be present in the finished steel. There are other aspects to be consideretl in connection with deoxidizing procedures. In addition to the primary objectives of oxide and gas control. the composition of the steel is affected by the elements introduced during the deoxidizing process. Factors in furnace operations are likewise involved, such as slag composition, temperature control. arid heat time. .ill of these should be considered in establishing the most satisfactory deoxidizing procedure for each grade of steel. The purpose of this paper is to outline the objectives of deoxidation as related to steel characteristics, and to summarize the factors in furnace practice and the economic aspects to be considered in connection with deoxidation procedures. Objectives of Deoxidation The primary objectives of deoxidation are the formation and elimination of oxides. The amount of oxygen present in the bath prior to deoxidation is an important factor, since it is the basis of any deoxidation procedure. The oxygen content of the bath is primarily a function of the carbon content, although it is affected also by the temperature, the oxidation of the slag, and transient conditions within the furnace. The relation of oxygen to carbon in the bath is shown in Table I. Table I shows that under actual operating conditions, the amount of oxygen present in the bath is higher than the theoretical amount. This relation would be expected, since the bath is in a state of metastablc equilibrium during the period that the carbon is being eliminated. The most important feature demonstrated by this table, however, is the rapid increase

Jan 1, 1945

By R. A., D. L. Sponseller, Flinn

Using specially del'eloped titanium nitride crucibles and a pressurized syslem, it has been possible to determine the solzibilitv of liquid calcium in liquid iron and iron-base alloys. At 2925°F the solubility is 0.032 wt pet Ca in pure iron. The solubility is increased by aluminum, carbon, nickel, and silicon additions, and lowered by additions of gold. An inflection in the calcium-solubility curve occurs as carbon is added to iron. At approximately 0.87 Wt pet Ca the CaC, phase replaces liquid calcium, and the calcium concentration de- creases as more carbon is added to the iron. The maximum solubility, 0.36 wt pet Ca, was obtained in iron containing 10.5 wt pet Si. The data have important implications regarding the use of calcium in process metallurgy, as well as providing an interesting test of theories of metallic solutions. Reasonably good agreement is found with theories of Alcock and Richardson and of Wagner, and criteria are suggested which permit these theories to be applied more readily to systems of this type. AT the present time relatively little is known about the factors influencing solubility in liquid metals. Information of this type is important for such matters as the control of impurity levels in liquid metals, the use of magnesium in ductile-iron production, and the use of liquid-metal alloys as fuels and coolants in nuclear power plants. One important example of restricted solubility concerns the extent to which liquid calcium will dissolve in liquid iron. This is a matter of considerable interest in view of the strong potential of calcium for removing certain impurities in steel,. as well as the ability of calcium to desulfurize, inoculate, and produce spheroidal graphite in cast irons.' Since ferrous materials normally contain other elements in addition to iron, the interactions of third elements with the Fe-Ca system are of interest. In view of the foregoing, this investigation was conducted to determine the solubility of liquid calcium in liquid iron and the effects of various third elements upon the solubility. For reasons of theoretical and engineering importance, the elements investigated were aluminum, carbon, gold, nickel, and silicon. Numerous attempts were made in the early part of the present century to determine the solubility of calcium in both liquid iron and steel, employing a variety of open-melt and closed bomb-type systems.2-4 From the results of these tests Wever concluded that calcium is insoluble in liquid and solid iron.5 These investigations were unsatisfactory in that they failed to insure the presence of a liquid layer

Jan 1, 1964

By F. F. Skiba, J. E. Warren

An idealized miscible displacement process in a three-dimensional, heterogeneous porous medium has been studied via experimental computation based on a "Monte Carlo"' model. The macroscopic dispersion which results solely from variations in the permeability of the porous system is related to the scale of the heterogeneity as well as the distribution function for the permeabilities. The interpretation of laboratory data is often subjective and may bt? misleading since ambiguities are not always recognized. Furthermore, an experiment performed on a conventional oil-field core does not yield a valid measure of Macroscopic dispersion for reservoir engineering purposes since the scale of heterogeneity that is significant in the laboratory is not significant in the reservoir. The analysis of field-performance data is discussed and it is shown that a unique characterization of the reservoir can not be obtained from this information alone. A possible method based on a minimum of data, for estimating the spatial distribution of permeabilities in a reservoir is postulated INTRODUCTION Many studies concerned with diffusion and dispersion in porous media have been undertaken because of the potential importance of miscible displacement processes for increasing the recovery of oil. The results from a large number of these studies have been published; in a recent paper Perkins and Johnstonl presented a comprehensive survey of the pertinent literature and excellent appraisal of the "state of the art". In this investigation, dispersion resulting from macroscopic variations in the properties of the porous medium is of primary interest. Dispersion, in this sense, is caused by fluctuations in the velocities of the individual fluid elements as they move through the porous system. This phenomenon is the result of inhomogeneities in the permeability and/or porosity, but it can be amplified by differences in the characteristics of the fluids involved. The objectives of this study are the following: (1) to determine the qualitative manner in which macroscopic rock properties affect the observed dispersion coefficient; (2) to evaluate the possible influence of macroscopic dispersion on laboratory experiments; and (3) to appraise the significance of macroscopic dispersion with regard to reservoir performance. Investigations of this type are essential since many miscible displacement processes, while seemingly understood from a mechanistic point of view, do not behave in a predictable manner under field conditions. Although a plausible explanation is that the process is dominated by the environment, little serious effort has been devoted either to describing the reservoir itself or to determining the probable effect of the reservoir properties on the process. This study is intended to be exploratory in nature; however, it is hoped that it will provide additional insight into the physical problem and that it will suggest areas suitable for further investigation. EXPERIMENTAL COMPUTATION MODEL To limit the observed dispersion to that which results solely from variations in the properties of the porous medium, an idealized process in which one incompressible fluid displaces another identical fluid is simulated. This simulation is achieved by means of a modified Monte Carlo method — by tracking a number of mathematical particles (tracer) through the system according to the steady-state, single-phase velocity distribution. Then the system is characterized by the distribution of the residence times of the particles. Since any number of particles can be injected simultaneously (a true delta-function distribution) and only pressure conditions are imposed on the boundaries, the model is completely determinate. Furthermore molecular diffusion, microscopic dispersion, adsorption and/or reaction are automatically precluded from the model. The heterogeneous medium is represented by a rectangular, three-dimensional array of uniform, homogeneous porous blocks which are randomly arranged; it is assumed that any two opposing faces of the system are held at fixed potentials

Jan 1, 1965

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By Leon Eliel

TEN years ago .a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these. isolated bits of infor-mation can be ascertained, the message begins to take meaning.. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936

By Wilbur E. Sanders

AT some period during the operation of metalliferous and other commercially valuable mineral-deposits in connection with their underground mining, when the developments therein have become so extensive that their description is tedious and confusing, some scheme for naming or numbering the various workings and their parts is necessary for convenience of ; reference.. A simple and symmetrical yet expansive system of classification must be devised, one that is capable of being extended to cover all possible exigencies and conditions of future operations within the property. Such a scheme, properly arranged, greatly simplifies communication between the various departments of the mining business, as, for instance, between the administrative and the operating departments of the concern, and is of the greatest assistance to the officers of the mine in enabling them to locate and describe particular points and parts of workings and specific kinds of work. Again, in the proper segregation and differentiation of mine-accounts, when they are carried out with that detail which will furnish ready information concerning the cost of a particular piece of work, or the various items and totals of expense connected with the, development,, operation and repair of each or all of the mine-workings, some such method of designation becomes a necessity. . Moreover, such a plan is admirably adapted to the needs of the mining engineer, who, in connection with his reports upon mining-properties, is sometimes required, in his descriptions of certain blocks of ore, to locate lists of assays of samples taken from many and various places, and to designate workings and parts of workings that are located in different parts of the mine, sometimes at points wide apart.

May 1, 1906