Search Documents

By H. I. Smith

CONTENTS [PAGE Problems of Mining and Processing Mineral Aggregates (TP 1649, by NATHAN C. ROCKWOOD, Min. Tech., Nov. 1943. Discussion by H. I. SMITH, IRVING WARNER and the author) t Mica in War (TP 1749, by RUSSELL G. WAYLAND, Min. Tech., July 1944. Discussion by H. S. SPENCE) 3 Three Roofing-granule Plants in Pennsylvania (TP 1787, by RICHARD M. FOOSE, Min. Tech., Jan. 1945. Discussion by H. I. SMITH)5 Methods of Prospecting and Mining Optical Calcite in Montana (TP 1896, by E. W. NEWMAN, Min. Tech., Nov. 1945. Discussion by W. C. STOLL and FRANK C. ARMSTRONG, and the Glass Sand and a Glass Industry in Puerto Rico (TP 1939, by HOWARD A. MEYERHOFF and J. EARL FRAZIER, Min. Tech., Nov. 1945. Discussion by A. M. SHORT, the author and PHILIP The "Bonanza" Mica Operation of Purdy Mica Mines, Limited, Mattawsn Township, Ontario (TP 2154, by HUGH S. SPENCE, Min. Tech., March 1947. Author's supplement and discussion by JOHN A. BAKER, E. J. LINTNER, and the author) 7 Process for Manufacture of Dead-burned Magnesite and Precipitated Calcium Carbonate from Dolomite (TP 2155, by ROBERT D. PIKE, Min. Tech., March 1947. Discussion by 0. C. RALSTON and the author) 9] Problems of Mining and Processing Mineral Aggregates H. I. SMITH*-Mr. Rockwood has presented a very interesting paper on problems of the mineral aggregate industry in meeting specification requirements, which apparently are ever decreasing in tolerance. May I call attention to a method of mineral separation that may be of value in separating the flat aggregate particles from the more angular ones and possibly the soft particles from the hard. The method is the old Pardee spiral coal separator, extensively used many years ago in the anthracite region for separating rock and bone from anthracite coal.1 The success of the process depends on the relative coefficient of friction of the aggregate particles to be separated rather than on their relative specific gravity. The flat and the soft particles normally will slide more slowly and stay on the inner spiral until they reach the delivery spout at the bottom whereas the round and the angular pieces will work to the outer edge and fall off into a spiral of larger diameter. The capacity of the separator is increased materially by having three inner spirals, with a separate feed for each, on which the particles travel more slowly, and one outer spiral from which the more rapidly traveling pieces slide to the bottom. IRVING WARNER*-I have long been convinced that much of the equipment and methods developed for mineral dressing might be advantageously employed in the mineral aggregates industry, and more particularly in the production of sand and gravel. The two industries are not well acquainted with each other or their problems. They have separate trade publications. The difficulty with the situation is that there are few large sand and gravel plants and few provided with technical services in their own organization or by retainer. This does not refer to engineering organizations but rather to improvement of plant technic in processing.

Jan 1, 1947

By H. R. Deeth, C. J. Koenig

ABOUT ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spence1 described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Corp. at Rochester, N. Y. THE DEPOSIT Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 [VOLUMETRIC MINERAL PER CENT Albite54 Microcline20 Nepheline22 Muscovite2 Mafics2 (Biotite, hastingsite, magnetite) Total100] The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2O A1203 6SiO2) and microcline (K20 A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1947

By Kenneth Robertson

THEREi9 probably less known of this subject than of any other connected with the metallurgy of iron. In all the books that treat of this mattes, there are given analyses of slags, their chemical formulae, the loss of iron, etc. ; but few, if any, give the character of the iron made at the time ; none give analyses and physical characteristics of the ores and limestones used, and they present merely isolated examples from various furnaces, and consequently one is more frequently puzzled than enlightened after reading them. During two years I have had occasion to analyze the slags and many of the pig-irons from two furnaces, and for this article I have made analyses of all the different grades of pig made by them. A

By F. T. Davis

Many contributors have added to the fund of knowledge in the basic sciences related to mineral dressing during the past year. During 1964, the French edition of the Proceedings of the VIth International Mineral Processing Congress together with discussions was printed. Also, complete Preprints of papers delivered at the VIIth IMPC were published in September1. Over a third of the papers presented at VIIth IMPC dealt with fundamentals. COMMINUTION It has been postulated by Ponceleta that flaws need not exist before a stress is applied but rather the flaws are created at the tip of a propagating crack at a stress well below the theoretical breaking stress.

Jan 2, 1965

By F. R. Morral, E. P. Miller

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By E. P. Miller, F. R. Morral

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By F. N. Speller

Interest in the corrosion problem seems to continue without abatement and is bringing practical results. At least four important conferences on this subject have been held during the last 5 months. Those interested in steel-frame structures are taking steps to study vulnerable points on account of the failure of some minor parts in certain buildings after 35 years of service. The steam power-plant group, including the railroads, realize the importance of a better knowledge of corrosion, especially under modern high-temperature boiler operations. The chemical and refrigerating industries have already conducted a systematic study of depreciation of metals by corrosion, for which they have spent considerable money and time during the last 2 years with encouraging results. More has probably been done to control corrosion in the atmosphere and in closed water systems, because the work on these phases of the problem started over 15 years ago and the important factors are now fairly well understood. As a result of all this work, there is now little excuse for corrosion in water conduits, recirculating condensers and cooling systems, since economical means of prevention have been worked out to meet nearly all situations where such corrosion occurs. The entire Baltimore water supply was treated with lime at a cost of only 35 c. per million gallons and the rate of attack on the pipes has been reduced to not over 20 per cent. of what it was before the treatment. Yearly damage to water mains in Baltimore is estimated at $300,000, and in New York City at $5,000,000, not including damage to water conduits in buildings. In some cities corrosion is now recognized by water works' engineers as a major problem. In the oil industry, there are evidently three general classes of corrosion, relating to: (I) Production, (2) transportation, and (3) refining. (1) Production.—Some fields, those of California for example, have little corrosion trouble in the wells. In others this is a major problem and should be a strong incentive to the development of more resistant metals at a reasonable cost. E. G. Woodruff,' consulting geologist, has pointed out that more of the oil of the future will probably come from the

Jan 1, 1927

(SECRETARY'S NOTE.) The following discussion of the papers of Van Hise, Emmons, Lindgren and Weed, read at the Washington meeting, February, 1900, and printed on pp. 282 to 498 of this volume, comprises communications to the Secretary, received at various times before the Richmond meeting, February, 1901, and, for the most part, presented at that meeting. These communications are introduced at this point in the present volume, in order that they may precede the papers of Vogt, hemp, Lindgren, Rickard, etc., presented at Richmond, and therefore not forming part of the material considered in them. Since many of the contributors have mentioned in one communication several of the papers referred to, no attempt is here made to divide their remarks and distribute the fragments under separate headings. In each contribution, however, the several topics are indicated by subtitles. R. BECK,* Freiberg, Saxony : Prof. Veal Hise's Paper.-The paper of Prof. Van use (p. 282) represents a great step of scientific progress, in that the circulation of underground waters has never before been presented with such clearness, ill the light of modern chemical and physical knowledge. The theories of the formation of ore-deposits which follow the author's general survey of the currents and solvent power of atmospheric waters in the earth's crust do not, indeed, seem to be novel, being essentially an amplification of Le Conte's views; but the proofs adduced in their support are in many particulars so original that no one can read without profit this portion of the paper. Entirely new (though largely in agreement with the papers of Emmons and Weed, presented at the same meeting of the Institute) are the sections dealing with the formation of the rich sulphides of the precious metals, and especially the regeneration of normal sulphides, such as galena, etc., in vein-zones immediately beneath the ground-water level. Nevertheless, it appears to me that Prof. Van Hise, in the course of his most instructive exposition of unquestionable, yet still locally limited, phenomena, has been too much biased in favor of the " descensionists." This is indicated by the small importance which he attaches to the intimate genetic relation between epigenetic deposits and the plutonic hearths of the earth's interior.

Jan 1, 1902

By G. E. Keller

In connection with the work of Committee D5, Coal and Coke, of the American Society for Testing and Materials in developing new standards and improving old standards, series of tests were made to check the variance of sample preparation and analysis of American coals. Table I in the "Tentative Method of Preparing Coal Samples for Analysis - 02013-62T" is rather complicated, and the tests were designed to develop data for the simplification of this table. An allowance of 20% of the total variance of sampling and analysis for the sample preparation and analysis steps was used. Also, instead of coals being grouped into ash ranges, they were grouped as washed and raw (unwashed) coals. As a result of these tests, a simplified Table I for Tentative Standard 02013 has been proposed. A standard test for laboratories to check their variance of sample preparation and analysis has been developed. Committee D5 on Coal and Coke of the American Society for Testing and Materials has been making a study of all standards applying to coal for the purpose of improving and bringing them up to date and for breaking some of the existing standards covering a number of tests into single standards. As an illustration, sample preparation is now partly covered in ASTM Designation D492-48, Sampling Coals Classified According to Ash Content, and partly in ASTM Designation D271-58, Laboratory Sampling and Analysis of Coal and Coke. The latter contains, in addition to parts of sample preparation, methods for determining Moisture, Ash, Volatile Matter, etc. Although revision of sampling methods and sample preparation methods are now assigned separately, it is possible that they may end up as one standard. One of the first new Tentative Standards developed as the result of these studies was ASTM Designation D2013, Tentative Method of Preparing Coal Samples for Analysis. Although this method is quite an im- provement over that in the old standards and gives very specific instructions, Table I (attached) is quite complicated and rather hard to understand. In order to take advantage of reduced quantities or weights, it is necessary to know the ash content within rather narrow limits before sample preparation and no distinction is made as to whether the coal is cleaned or uncleaned. No limits of accuracy are assigned to the sample preparation and analysis. The total over-all accuracy of sampling, preparation and ash determination as given in D492-48 has been specified for commercial sampling procedure as follows: "This procedure is intended for an accuracy such that if a large number of samples were taken from a single lot of coal, the test results in 95 out of 100 cases would fall within ? 10 per cent of the average ash content of the sample." Although Appendix 11, Method for Determining the Over-All Variance of Reduction and Analysis in the Tentative Methods for Mechanical Sampling of Coal, ASTM Designation D2234-63T, does give a method for determing the over-all accuracy of preparation and analysis expressed as variance and also the F test, it does not permit the determination of the variance at the various stages of reduction or of the ash determination. It was decided in 1961 to ask a number of laboratories to run a series of tests for the purpose of determining the variance at various stages of reduction and analysis with the view of simplifying Table I of the Tentative Standard D2013-62-T. This paper is a record of this series of tests with recommendations which resulted from the tests. At the same time and preceding these tests the International Organization for Standardization under Committee TC/27 WG 7 was studying the same problem. Tomlinson1 of England and Dr. paul2 of West Germany had made studies giving quite a bit of information. Also Schwerd and coryel13 published some information which was the main basis for the Mechanical Division provision in ASTM Tentative Standard D2013-62T, Table I. In checking with the various laboratories which offered to cooperate in these tests, none was found which used mechanical division through the entire preparation procedure. It was then decided to use riffles at all stages with the thought that if riffles gave satisfactory variances, approved mechanical

Jan 1, 1965

By Ionel I. Gardescu

In connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,' an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the displacement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S6, R4, the sand reservoir R, R1, R², F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415Ib. per sq. in. with no free gas present. This was ascertained by closing off all the outlet valves and determining the coefficient of compressibility of the system by means of the displacement chamber D. Much difficulty was encountered in eliminating all of the free gas masses from the oil reservoir. The dead oil originally present in the

Jan 1, 1932

By A. Phillips, H. J. Fisher

The influence of temperature and composition on the viscosity of high-purity liquid metals and alloys of the Pb-Sn and Sb-Cd systems was investigated by the logarithmic-decrement method. The variation of viscosity with temperature above the liquidus followed the equation: n = AeE/RT No large increase in viscosity was found just before normal freezing of any of the metals or alloys investigated. Certain alloys, supercooled below their stable liquidus, however, did show a marked increase in viscosity. Experimental activation energies for viscosity were determined for the metals investigated. Liquid-metal density values were obtained by a modified Joeger's method. IK an investigation of the properties of molten metals, the study of viscosity as a suitable means for studying the physical nature of the metallic liquid state has been utilized. Although interest in the relationship of the liquid to the solid-metal state holds promise of broadening the knowledge of metals in general, much information that is available regarding the influence of temperature and composition on viscosity, especially near the freezing point, is still controversial. The purpose of this paper is to present the results of recent work on this subject. Although interest in factors influencing the fluid behavior of metals and alloys has arisen from theoretical as well as applied studies of liquid-metal properties, the development of a comprehensive theory of the mechanism of viscosity has been handicapped because so little is known about the liquid state. Several theories of viscosity have been proposed and among the more recent are those of Andrade,1 Bernal,2 Frenkel,3 Eyring,4 and Gutmann and Simmons.5 Athough these contributions have helped to establish a basis of approach for studying the nature of viscosity, the fundamental aspects of the variation of viscosity with alloy composition have, in general, been neglected. Experimental Metals and Alloys Investigated: The Pb-Sn and Sb-Cd alloy systems were selected for investigation because they form constitutional features of theo-

Jan 1, 1955

By C. H. Stewart, R. A. Fagin

A two-dimensional, three-phasereservoir simulator was programmed for a large memory digital computer. It was designed to provide a practical solution to describing the complex physical relation between the natural forces and the physical properties of a heterogeneous reservoir when subjected to a specific set of conditions. A reservoir study is briefly described to illustrate application of the model. A full volumetric account of three phases (oil, gas and water) is performed simultaneously throughout an integration net representing the reservoir. Absence of one or two of the phases is treated as a special case of the more general situation. Expansion (or contraction) of all phases, including rock expansion, is performed so that the pressure calculation is the general unsteady-state case. To account for the large variations of subsurface elevation encountered in some reseruoirs, and to allow for segregation of the various phases, a gravity head term is included in the basic drive potential. Appropriate fluid and rock properties are used in polynominal surface form (functions of pressure and/or depth) or they can be entered as space variables at each position of the integration net. An unsteady-state water influx calculation, based on the method of van Everdingen and Hurst, l was connected to the boundary of the matrix to simulate aquifers of various sizes. In addition to reservoir calculations, three-phase fluid flow from the producing depth to the wellhead, including provisions for gas lift, was incorporated in the simulator. A workover routine was also built which can automatically switch to a different set of production relations when a gas-oil ratio or water fraction reaches a limit; or it can shut-in the well if prescribed. INTRODUCTION This paper describes a reservoir engineering mathematical simulator used to represent the complex interaction of natural forces and physical properties of a reservoir during natural depletion or with various injection schemes. The simulator, which was programmed for a large memory digital computer, is a two-dimensional calculation which handles three mobile fluid phases simultaneously (oil, gas and water). Basic requisites for the method are individual well production and pressure data, hydrocarbon fluid properties, geological data (producing depth and net sand), capillary pressure data, relative permeability data and permeability and porosity information. Matching the past performance of a combination drive reservoir often has yielded information concerning continuity and the validity of basic data. Detailed predictions of future performance can be made for continuation of current depletion methods (natural depletion) as well as for various types of recovery by gas or water injection. Combination injection cases and pattern studies can also be performed. Workover programs, gas lift and different types of artificial lift programs have been investigated using a technique similar to that described by Kern and Nicholson2 except that conditions of pressure and saturation at the block within which the well is located are used rather than average reservoir conditions. Drilling additional wells to optimize profit was explored, both as to number and location, by placing wells at different spots within the reservoir matrix. Special depletion processes can be examined, such as upstructure drainage and lateral (or strike) waterfloods in thin oil columns. In one case the mathematics of the simulator were modified to calculate the displacement in the vertical plane rather than in the horizontal plane. In this manner specific reservoir problems can be studied, such as coning of gas and/or water around production points, fingering along permeable stringers or, more generally, frontal advances in a heterogeneous section.

Jan 1, 1967

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By Dale I. Hayes

Combined loader and transport, the Gismo is now built for sale in one size, 5 to 6 tons. It will operate in a minimum opening of 7x7 ft and can be built to operate at lower heights. Where space limitations are not a factor it could be designed with much greater carrying capacity-12, 18, or 25 tons-to be powered with a standard heavier tractor. The Gismo is mounted on crawler tracks of the same design as the tracks of the small Allis- Chalmers HD-6B tractor used to power it. With the HD-6B tractor it will negotiate upgrades of 12 pct and downgrades of 20 pct. The next tractor size would make the device feasible for steeper grades or for a machine of larger capacity at moderate grades.

Dec 1, 1956

By Ross W. Smith, Salim Akhtar

INTRODUCTION Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collectors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By Carl A Zapffe, George A. Moore

In a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal substructures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the L'disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, unaffected by chemical attack and undis-torted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. Materials Studied In commercial steels, defects caused by hydrogen take various external forms according to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement—-"pickling brittleness "—in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free-machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group 1: Prepared from Armco Ingot Iron As shown in Table 1, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By Carl A. Zapffe, George A. Moore

In a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal substructures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the L'disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, unaffected by chemical attack and undis-torted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. Materials Studied In commercial steels, defects caused by hydrogen take various external forms according to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement—-"pickling brittleness "—in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free-machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group 1: Prepared from Armco Ingot Iron As shown in Table 1, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By Charles E. Lundin, Albert S. Yamamoto

The phase eqrtilibria of the binavy system, Nb-Al, weye established by metallographic, X-ray diffraction, hardness, and thermal-analysis techniques. Three intermediate phases were identijied, Nb3.41, Nb2Al, and NbAl,. The N6,Al and NbAl phases have extensiue ranges of solubility. The maximum solubility of aluminum in niobiuitz is 23.0 i0.5 at. pct (8.0 wt pct) A1 clt 1960" i 10°C. The maximumt solinbility oj niobiunz in alunzinutz is less than 0.3 i0.1 at. pct (1.0 tut pct) fib. The A'h,Al and Nbgl interinediate phases forr peritectically at 1960° 1UcC and 1870" i 1U9C, respectively, zuhereas the NbAl, phase fornts congvuently fio11t the melt at 1605" 10°C. A eutectic reaction oc- The intent of an over-all research program was to develop niobium-aluminide-base coatings for refractory metals since these coatings exhibit useful high- curs at 57.8 i 0.5 at. pct (28.5 wt pet) A1 and 1500" 10°C between NbAl and NbAl3. The aluminum-rich region of the system has a peritectic reaction where liquid reacts with NbAL, to form aluminum solid solution. Structural and lattice -pavarneter data /or the intermediate phases were determined by X-ray diffraction analyses. An unusual transfov?nation having charactevistics of nucleation-growth and martensitic nleclanisils occurs on cooling the niobium solid solution in the region from 18 at. pct (6 wt pct) Al to 23 at. pct (8 wt pct) Al. The transfornzed product on rapid quenchirzg is an acicular NhAl. temperature resistance to oxidation. As a prerequisite, the phase equilibria of the system, Nb-A1, were necessary. A literature survey revealed that the phase-equilibria data reported by various investigators were rather incomplete and conflicting. Therefore a complete determination of the system was undertaken by the authors from 0 to 100 pct of solute addition.' In 1959 Savitskiyz presented a tentative diagram which

Jan 1, 1967