Search Documents

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

By S. F. Emmons

The history of the mining region of Custer county has been somewhat peculiar. Although, in the broader features of geological structure, it bears a strong resemblance to its newer and now more famous neighbor, 40 miles to the northward, the Cripple Creek mining district, it has been noted for failures rather than for successful mining ventures. Yet it has a number of mines that have proved themselves to be remarkably rich, and many others that have well-defined veins and very rich ore, though they never have been worked to any great depth. A few of the deposits seemed to the early miner so anomalous in form and manner of occurrence that they were popularly described as " contrary to all geological laws." The region has had several " booms," succeeded by more than usually violent reactions, the latter having proved more permanent than the former. It was, for a long time, the favorite resort of patent-process mongers, and the ground is now strewn with relics of various unsuccessful reduction-plants. Mismanagement, ignorance and disagreements among mine-owners seem to have been quite as responsible for the want of success in the region as the quality of the ores or the form of the deposits. In the early eighties, when the booms had not entirely died out, a division, then under my charge, of the U. S. Geological Survey, undertook an examination of the region for the purpose of making a study of its ore-deposits. The areal survey was carried to completion by Mr. Whitman Cross, but the study of the mines could never be completed for the reason that most of them were closed, for one reason or another, before we had time to visit them. From time to time, one or another of the important mines has been started up again, but it was not

Jan 1, 1897

By Walter Snelling

IN the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I 'experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment.

Jan 4, 1915

By R. M. Brick, Arthur Phillips, A. J. Smith

A PREVIOUS publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuA12. A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation. to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. STRAIN IN SOLID-SOLUTION ALLOYS A 10 per cent magnesium alloy in the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using aluminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl2, CaC12, NaCl. Chill-cast rods were sealed under vacuum

Jan 1, 1935

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman' developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,' and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,' as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman's work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By W. P. Heineken, A. T. Child

This paper presents the results of a series of experiments made in the metallurgical laboratory of Columbia University, New Pork City. The object of the investigation was to determine, as far as possible, the changes in micro-structure and physical properties caused by short periods of heat-treatment and the longer malleable cast-iron process. It was proposed to do this by means of micro-photographs, heating- and cooling-curves, and tensile tests after the various heat-treatments. I. Micro-Constituents of Iron and Steel. The list of the micro-constituents of iron and steel has grown till now it includes seven different substances, called ferrite, cementite, pearlite,* martensite, austenite, sorbite and troosite. Only the first five of these are mentioned in this paper, to facilitate the understanding of which, the following brief definitions are given: 1. Ferrite (named by Prof. Howe) is, chemically, iron free from carbon. It is the softest of the constituents, and is not colored by etching, except when long-continued. Under the microscope it is easily determined by its regular polygonal etructure; or, if structureless, as in malleable cast-iron, by the ease with which it is scratched. Ferrite appears in mild steel in small amount, in grey cast-iron, and in malleable cast-iron. 2. Cementite (also named by Prof. Howe) is now generally conceded to have the formula Fe3C. It is the hardest of the micro-constituents, having the hardness indicated by 7 of the mineralogical scale; and hence it is always left in relief after

Jan 1, 1901

By Arthur C. Forsyth, R. L. Dowdell

A search through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1. Experimental Procedure The alloys were prepared from metals of commercial purity, as follows: electrolytic nickel 99.60 + 0.35 Co; chemically purified silicon 99.79 per cent plus impurities of Fe 0.027, A1 0.008, Ca 0.014, C 0.004, N² 0.10; and cobalt 98.82 per cent plus impurities of Ni 0.42, Fe 0.12, CaO 0.27, S 0.012, Mn 0.10 and SiO² 0.15. It should be noted that the largest impurity in cobalt is nickel, one of the alloying elements. The alloys were melted in a small Ajax induction furnace, the nickel and cobalt being melted first because of their better ferromagnetic

Jan 1, 1940

By Arthur C. Forsyth, R. L. Dowdell

A search through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1. Experimental Procedure The alloys were prepared from metals of commercial purity, as follows: electrolytic nickel 99.60 + 0.35 Co; chemically purified silicon 99.79 per cent plus impurities of Fe 0.027, A1 0.008, Ca 0.014, C 0.004, N² 0.10; and cobalt 98.82 per cent plus impurities of Ni 0.42, Fe 0.12, CaO 0.27, S 0.012, Mn 0.10 and SiO² 0.15. It should be noted that the largest impurity in cobalt is nickel, one of the alloying elements. The alloys were melted in a small Ajax induction furnace, the nickel and cobalt being melted first because of their better ferromagnetic

Jan 1, 1940

By W. P. Ward

I desire ho put on record a fact in relation to the effect of man ganese on pig iron which I have never seen in print, and which may, perhaps, not have been observed by anyone except myself. In 1875, while experimenting on the production of ferroman ganese in a blast furnace, I had burdened the furnace with a charge which I calculated would produce a 15-per cent. spiegel. The fur nace was very hot, having been running for a couple of days on a very light burden, and making a burnt iron, preparatory to the experiment I proposed to make to produce a high grade of spiegel. I calculated that the charge would begin to work in the fur nace in about twelve hoars after it was put on. After the -lapse of that time I commenced to watch the furnace carefully, but found little or no change in the appearance of the metal, although there was a very decided change in the cinder, showing that the man ganese ore had come in work. The iron was quite gray and very tough. The character of the cinder was good for a spiegel cinder, and 1 could not imagine where the manganese was going to, as it (lid not appear to be in either metal or cinder in anything like the quan tity indicated by the charge. The next morning things were still in the same condition. The furnace was very hot, the cinder good, and the iron very gray. I was then sorely puzzled. I had never heard of a gray iron with over 4 or 6 per cent. of manganese, and had no notion that an iron with more manganese could be gray and tough. With great difficulty a piece for chemical test was broken from a pig. Not less than a hundred blows from a heavy sledge were required to break it off, I took the specimen to the shop and directed that some borings from it should be brought to the laboratory, as soon as possible, whither I myself at once repaired to put things in readi ness for a rapid manganese determination. In about half an hour the machinist came in with the iron specimen in one hand and about a dozen blunted and broken steel drills in the other, saying that it mas impossible to drill the iron. There were several little depressions in the iron, which was malleable enough to be indented by the point of the drill, but not a chip had been cut from it. The metal was never subjected to further physical tests. A chip broken from

Jan 1, 1882

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron' and molybdenum.' The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,' containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln' wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,' mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953

By Horace V. Winchell

The laws here referred to are those which define the status of the prospector for mineral deposits in the soil or beneath it, establish his methods of procedure, protect him in his possession while searching for the subterranean treasures, and give him assurance of title when all required conditions have been fulfilled and valuable minerals discovered. Regulations for the operation of mines and the safety and health of mine employees are likewise subjects of Federal and State legislation, but are not within the scope of the present program. Various features of our present laws will be discussed in detail by able students of the subject, and specific remedies will be proposed for the most glaring defects. It is my purpose to present in this paper a summary review of the reasons why revision is needed and demanded by the great majority of those in daily contact with the industry. Reason Number One The first objection to the continuance of the present law is that it was not planned by its framers and the Congress which passed it to apply to many of the kinds of mineral deposits, nor to the mining conditions, which are controlled by it to-day. In 1866, under the title, "An Act granting the right of way to ditch and canal owners over the public lands, and for other purposes," was surreptitiously smuggled into existence our first mining law (14 Stats. at Large, Chap. 262, p. 251). This law provided that "whenever any person or association of persons claim a vein or lode of quartz or other rock in place, bearing gold, silver, cinnabar or copper, having previously occupied and improved the same according to the local customs or rules of miners in the district where the same is situated," etc., a patent might be granted an certain conditions. This was evidently an Act intended to validate claims already initiated, and to accord Federal recognition to mining locations made in

Jan 1, 1915

By W. J. Millard

IT is well known that the excellent mica from Brazil played a most vital role in World War II. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the United States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. TYPE OF DEPOSIT FAVORABLE The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than I:3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. THE ECONOMICS OF STRIPPING When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run II per cent good stain and better when trimmed and contain 2 kg. of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should he used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.I4 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.I5. To this should be

Jan 1, 1946

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By J. J. Becker

Changes in magnetic properties with particle size are used to study the precipitation process in a Cu-Co alloy. In particular, the effect of a field during aging in producing anisotropy is shown to occur entirely during the growth of the particles, after precipitation is complete. HEAT-treatment in a magnetic field is done commercially to improve the magnetic properties of a number of materials. These can be divided into solid-solution alloys and precipitation alloys. The Permalloys are representative of the first type, and magnetic annealing greatly increases their maximum permeability. On the other hand, in precipitation alloys such Alnico 5 the important result is an increase in maximum energy product. The effect of the field in all cases is to bring about an additional magnetic anisotropy, uniaxial in nature, which makes the hysteresis loop more upright when measured in the direction in which the field was applied. The structural origin of the anisotropy brought about by magnetic annealing is not well understood. In the solid solution alloys, one possible explanation is based on ordering.' Another possibility is the orientation of like-atom pairs.' The precipitation systems known to respond to magnetic heat treatment are Alnico 2, in which the effect was first discovered," Alnico 5, cobalt ferrite (oxide),' and Cu-Co alloys.3 n these materials, the field affects the precipitation process itself in some way. Although there has been much work on Alnico 5. its nature is still incompletely understood. According to Geisler,' the precipitation reaction is of the

Jan 1, 1959

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.' It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

By Waldemar Lindgren

CONTENTS. [ ] I.-CHARACTER OF THE DEPOSITS. 1. Principal Features. IN many schemes of classification and description the term contact-deposit has been somewhat loosely applied to all accumulations of useful minerals (other than those of unquestioned sedimentary origin) which are enclosed between two different rocks. As thus used, the term may include deposits of widely differing origin, and, unless qualified, is not in place in a genetic classification. The present paper deals with a special class of contact-deposits. In many geological provinces, granular igneous rocks, such as granite, diorite and syenite, have broken through and invaded sedimentary rocks. The molten magma may in part have reached the surface and there solidified with relative rapidity as a lava. The largest masses of it, however, did not reach the surface, but cooled very slowly at considerable depth under great pressure, and eventually consolidated into a rock of granitic texture. Uplifts and extensive erosion may have followed; and at the present day, in many places, thousands of feet of material have been removed, bringing to the surface the intrusive granular rocks and their once deep-seated contacts with the sedimentaries which they shattered at the time of in-

Jan 1, 1902