Search Documents

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944

By P. Bandopadhyay, T. C. Rao

Geologically the Indian coals belong to Gondwana formations. Being of drift origin, these coals contain high percentage of mineral matter distributed in finely disseminated form. Indian coal-preparation plants process prime coking and medium coking coals for use in steel plants. Limited resources of good quality coking coals (Table 1) could not keep pace with the rapid developments of the iron and steel industry in India. This resulted in the introduction of coal-preparation technology and the establishment of washeries in India in the last 30 years or so. The first four washeries were set up during the early fifties at West-Bokaro, Jamadoba, Lodna and Kargali. Next came the first non-coking coal washery at Nowrozabad set up by the Associated Cement Company. In 1961, following the recommendation of Central Coal Washeries Committee (1953-54), Hindustan Steel Ltd. had set up five central washeries at appropriate locations, viz Durgapur, Dugda (2 washeries), Patherdih and Bhojudih, so that the raw coal feed having similar washability characteristics can conveniently come from a number of collieries to a particular washery. Subsequently, to meet the increasing demand of metallurgical coal by steel plants, two more central washeries (at Durgapur and Chasnala) and three pit-head washeries (at Kathara, Swang and Gidi) were installed by 1970. The prime objective of washing Indian coking coal is essentially to reduce the ash content. All the washeries in India, taken together have an installed capacity of about 26 million tons of raw coal input per annum. Details of these washeries in respect of their annual capacity, main washing systems adopted and the nature and size of the products are given in Table 2. It can be observed from this table that (1) bulk of the coal is processed in units like jigs HM baths and HM cyclones; (2) only two of the washeries have cleaning circuits for treatment of fines.

Jan 1, 1980

By D. F. Hewett

ALTHOUGH most persons will agree that an individual or a nation can profit from the experience of other individuals or nations, there is always room for debate over the degree of similarity of their past and present conditions and of their future problems. Noting the increasing interest that Americans are showing in our mineral problems, I have felt that we could profit from reviews of the experiences in mineral exploitation acquired by the industrial nations of Europe. Whether we can learn much from Europe's experience in exploiting such minerals as petroleum may be debatable, but certainly, with a record of metal production extending back nearly 3000 years, Europe should hold much of value for America. A trip to Europe in 1926 permitted me to visit 28 mining districts, of which about half are now or have been in times past outstanding sources of several metals. The districts range from England to Greece and from Spain to Poland. To summarize briefly my impressions of these mining districts, as well as such reactions to the thought and life of Europe as so short a visit permits, I shall only venture the opinion that Americans can review with great profit the ideas and actions of Europeans, with regard not only to the production of metals but to many expressions of life. I believe that America has made and is making new contributions to the art of living, as well as to the arts of mining and metallurgy, but in so far as Europe is and has been a laboratory of economic, social and political experiments, the results she has attained deserve the thoughtful attention of America. I have come to believe that many of the problems that harass Europe lie in our path not far ahead. I have therefore hoped that a review of metal production in Europe in the light of its geologic, economic and political background may serve to clear our vision with regard to our own metal production. One can not examine the literature of national metal production without being impressed that the countries of continental Europe, especially Germany and Austria, have shown greater interest and devoted more time to research into the record of metal production than Great

Jan 1, 1929

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

INTRODUCTION IN a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress.‡ The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into use with the same significance as "technical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens between yield and fracture. A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress S3 to the longitudinal stress Sl.* The results of the experiments are represented by a series of complete flow-stress curves for each of the metals investigated, and these diagrams have been used for the development of other diagrams of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not on the stress system, he was correct in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, would seem to be axiomatic, provided that the flow stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard of this principle has led to some untenable theories of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1948

By H. M. Howe

One of the little electric-resistance magnesia crucible-furnaces which I designed for the metallurgical laboratory of the School of Mines of Columbia University is shown, in vertical section, of full natural size, in Fig. 1. The furnace itself consists of two semi-cylinders of magnesia, A A, with a cover of magnesia, B B, and a stopper, C, also of magnesia, which is perforated to admit the leads x, y, of a thermo-electric couple. The furnace is heated by the spiral of platinum wire, D D (entering and departing by the openings I and K), through which a current of any desired strength is passed, bringing it to incandescence, and to ally temperature, not above the melting-point of platinum, which may be desired. The crucible E, actually used in this furnace, is also of magnesia. I have heard of some unsuccessful attempts with furuaces of this general class, and have attributed these failures to the use of siliceous materials for the furnace-walls. Of course such a result is what we should expect, since the silica mould readily be electrolysed by the current, and the resultant silicon would alloy with platinum ; but the little magnesia furnace here clescribed seems to be wholly free from this objection. It has been used in my laboratory for some months, and temperatures, up to 1100° C, hare been developed in it over considerable periods of time—indeed, it has been held near 1400" C. for about two hours—without indication, thus far, of any deterioration of the platinum. In the section shown, F F are a pair of steel disks, bound together, but separated by the inverted thermo-junction, N, of the thermo-electric pyrometer. This arrangement permits the observation and record of retardations in the heating and cooling of F F—in other words, the determinations of the cooling curves of steel—a purpose for which the furnace has been used, thus far, more frequently than in the determination of meltingpoints. For the latter operation, however, it is also suitable.

Jan 1, 1902

By E. R. Macgregor, J. Halpern

The kinetics of the reduction of cupric salts in aqueous solution by molecular hydrogen to metallic copper are described. The rate of reduction appears to be homogeneously determined and shows a marked inverse dependence on the hydrogen-ion concentration. Precipitation of copper is more rapid and complete in sulfate than in per-chlorate solution. A mechanism is proposed which accounts for this behavior. IN recent years a number of important hydro-metallurgical processes have been developed in which metallic salts in aqueous solution are reduced by gaseous hydrogen, usually at elevated temperatures and pressures, and thereby precipitated either in metallic form (e.g. Ni, Co, Cu) or as an oxide or salt of lower valence (e.g. VO, and VA).1 ; In connection with applications such as these, most of which involve heterogeneously catalyzed reactions, recent demonstrations"-" that salts of certain metals, e.g., Cu", Ag' , Hg" , and Hg,+ can activate molecular hydrogen homogeneously and thus catalyze hydrogenation reactions in aqueous solution, are of considerable interest. For example, cupric salts catalyze the otherwise slow homogeneous reduction of dichromate and ceric salts by hydrogen, i.e. Cr,O; + 3HL. + 8H1 ? 2Cr'- -- 7H,O [1] 2Ce ' ! H.. ? 2Ce" | 2H . [2] In perchloric-acid solution, where Cu" is not appreciably complexed, the kinetics have been found" " to be of the form -d [H,] _- k,[HJ [CU"]' dt -LCu+' l+ (k ,/k,) [H] [3] where, K = 1x10"' exp [—26,600/RT] 1, mole-' min-' ... [4] and (k ,/k,) - 0.25 at 110°C. This kinetic behavior suggests that the reaction proceeds by a mechanism involving the following sequence of steps kt Cu" +H1CuH' 4-HA [51 k., CUH + CU" ? + 2Cu f H' [GI 6Cu'+ Cr,07 + 14H'+ 2Cr- (¦ 7H,O + 6Cu" ['i] fast The catalytic activities of the undissociated cupric-sulphate and cupric-acetate complexes are somewhat greater (by factors of 6.5 and 120, respectively) than that of the simple hydrated Cu" ion.'" These considerations suggest that, in contrast to the other hydrometallurgical hydrogenation reactions, referred to previously, reduction of cupric salts in aqueous solutions by molecular hydrogen, should proceed homogeneously, and in the absence of an extraneous catalyst. This has already been demonstrated" for acetate-buffered solutions where the product of the reaction is a precipitate of cuprous oxide (Cu,O). In the present paper, an investigation of the reduction of cupric salts in perchloric-acid and sulphuric-acid solutions, leading to the precipitation of metallic copper, is described. Some results for the sulphate system, which is of considerable hydrometallurgical interest, have been reported previously by Ipatieff",' " and by Schaufel-berger' but these do not give a quantitative account, of the kinetics and mechanism of the reaction. Experimental The reduction experiments were conducted in the 1-gal, titanium-lined autoclave described in connection with earlier related investigations," " and using a similar procedure. The solutions were made up by dissolving known amounts of CP grade Cu(ClO,), and HC10, (or CuSO, and HISO,) in dis-tilled water. While in the autoclave, the solution was stirred and maintained at a constant temperature (±loc) and under a constant partial pressure of hydrogen gas. It was ascertained that the agitation (provided by two 3-in., four-bladed stirrers, rotating at 900 rpm) was adequate so that at no time was the rate of reaction limited by solution of hydrogen. During each experiment, samples of the solution were withdrawn periodically, allowed to cool, and the concentration of copper remaining in solution was then determined electrolytically. Some Cu' is formed during the reaction, but undergoes disproportionation when the solution is cooled to room temperature. For purposes of kinetic calcula-

Jan 1, 1959

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

Air-sand Process of Cleaning Coal Discussion of paper by THOMAS FRASER and H. F. YANCEY, presented at the New York Meeting, 1926, and issued, as Pamphlet No. 1561-F, with MINING AND METALLURGY, February, 1926. T. DEVENNY, Edgarton, W. Va.-How near the size of the sand can the coal to be treated be brought? Do you use an 8-mesh coal on that cleaner? J. J. RUTLEDGE, Baltimore, Md.-From the little I have seen of the apparatus in operation, I should say 8-mesh. In my experience in metalmine concentration work, trying to separate different minerals on one jig, sometimes I have succeeded and sometimes not. This apparatus has appealed to me; something of this kind should be useful with the silicates and carbonates of zinc. I think this apparatus has possibilities in metal mining. Recently in our coal field a screen has been introduced for cleaning coal; it is giving excellent service. When I asked the inventor why he did not take it to the metal mines, he said there was a good and sufficient reason, in a patent way. There may be reasons why it would not be applicable for metal mining; but the simplicity of it appeals to me and I cannot see why it could not be so used. T. FRASER (written discussion).-We feel that 8-mesh would be about -the minimum size of coal practicable to treat by the air-sand process. This would depend partly upon the friability of the coal. The more nearly the lower size limits of the coal- approaches the size of the sand, the more .time will be required in screening the sand out of the cleaned coal, which would mean a little more chance of breakage. In regard to the treatment of ores; this would necessitate the use of some heavier mediums than ordinary silica sand, or some other means of making the separation at a higher specific gravity than is required for coal. We are now working on a method of obtaining this effect for the preparation of anthracite coal without resorting to the use of heavier and more expensive material than common sand.

Jan 1, 1927

By Albert S. Trube

Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of reservoir fluids well in advance of more accurate laboratory data. One such factor is the isothermal coefficient of expansion of an undersaturated hydrocarbon liquid which may be contained in a particular reservoir. This coefficient, or liquid "compressibility", has often been assumed to be relatively insensitive and nearly constant. Although this assumption may be nearly correct in the case of high specific gravity liquids, it cannot apply in the case of medium to low specific gravity liquids. Any treatment of the nature of liquid compressibilities must give consideration to the variable nature of the isothermal expansion coefficient and the fact that it can be both pressure sensitive and temperature sensitive. The isothermal coefficient of expansion, or compressibility, of a substance is defined as -c = 1/V (?V/?p)T......(1) The value of Eq. 1 may be approximated for a finite pressure change by using the well-known relation, c = V1 - V1/Ve (p2-p1), ........(2) in which p1 > p1 and V2 > V2 and V1 + V2/2. The instantaneous compressibility may also be estimated from the slope of a curve on which log V is plotted vs pa. In this instance, it has been shown that c = In V1/V2/p2-p1 ...........(3) Eq. 3 may be used for variable compressibilities by plot-ting V vs p on semi-log paper. In this case, the instan-taneous or point compressibility is c = 2.303 m.......... . (4) in which m is the slope of the curve at a point in log cycles per psi. ISOTHERMAL COMPRESSIBILITY OF UNDERSATURATED LIQUID In the case of gases, the compressibility has been defined by Muskat' and others as Co = 1/p - ?z/z?p ..........(5) This was later generalized through application of the theorem of corresponding states' to co = 1/pr - (?z/z?pr) T8 ........(6) in which c, is defined as the pseudo-reduced compres-sibility and is numerically equal to (c.p,) and the sign is arbitrarily changed for mathematical convenience. Eq. 6 is general and applies to gases and liquids. In the case of liquids, c. = c1,pe, but if Eq. 6 is used, values of z and ?z/?p, must be determined for the liquid in question. The difficulty of obtaining accurate values of ?z/?p,, particularly in the region where T, is approaching 1.00, was pointed out in the previous paper'. This method of approach is unreliable for extension into computations of liquid compressibilities. On the other hand, c, can also be defined as follows: - Cr = 1/Vr (?Vr/?pr) Tr ......(7) and from which, Cr = 1/pr (?pr/?pr) Tr .....(8) In accordance with the theorem of corresponding states, Vr = V/Vr, p, = p/pr and pr = p/pr. Ref. 2 pro-vides an excellent source of reduced density, reduced pressure and reduced temperature data for a wide variety of fluids. For the purpose of this investigation, the set of fluids2 having ze = 0.27 was chosen because it in-cludes most of the heavier hydrocarbons usually found in those complex mixtures loosely defined as "reservoir oils". Data on undersaturated liquids in Ref. 2 were rearranged to conform with Eq. 8. To simplify the computation of cr, the isothermal p, data were plotted vs the log of pr, in which case for any straight line or tangent cr = 1/M pr pr .....(9)

Jan 1, 1958

By R. V. Whetsel, Valentin R. Garfias

Mexican petroleum production for 1928 was approximately 50,000,-000 bbl., the lowest in 12 years, showing a decrease from 1927 of over 14,000,000 bbl. The steady downward trend for the past 7 years has allowed Russia to outrank Mexico by a wide margin for third position and if the expected decline continues during 1929 it should place Persia ahead of Mexico as fourth in rank. The year 1928 was characterized by a continuation of the reentrench-ment previously begun by the oil industry in Mexico in an attempt to adjust itself to the adverse conditions caused by the steady depletion of the fields, the rapidly increasing competition from Venezuela and the United States and the as yet unsettled petroleum legislation and taxation situation. With the exception of the Isthmus of Tehuantepee, drilling in proved fields was considerably curtailed and although the number of wildcats completed exceeded those of the previous year, no extensive drilling programs were undertaken. Practically without exception, the major companies reduced personnel and operations to a point where they could meet existing conditions and mark time while awaiting a more stable basis for the future testing of unexploited regions. Many terminal and transportation facilities were abandoned during the year. Development Only 371 wells were completed during 1928, as against 583 in the previous year and 808 during 1926, and although the percentage of producers in 1928 was 34 per cent., compared to 26 per cent. in 1927, the initial production of -wells was considerably lower than during the previous year, a great number of the wells showing salt water and becoming "strippers" from the time they started to flow. Development is summarized in Table 1. Drilling in the Northern fields did not prove any new pools of importance, the most successful wells being located in the old producing areas of Cacalilao, Panuco and Topila. (Fig. 1 Very few of the producers made more than 1000 bbl. daily, and a great many less than 300 bbl. a day.

Jan 1, 1929

By A. F. Melcher

The present paper is a progress report on an investigation of the physical factors of oil and gas and especially of their sands,' such as pore space, size of pores or permeability, retentivity, viscosity of the oil, temperature, pressure, thickness and area of the pay sand, water relations, and capillarity. The purpose is to determine as many of these physical factors as possible, and to ascertain the relations existing, directly or indirectly, between these physical factors and the production of oil and gas. As yet only pore space2 and size of grains of pay sands have been investigated, although an apparatus has been designed to determine the permeability of a sand to oil, water, or gas under definite drops of pressure between the entrance face and exit face of the sample. Messrs. E. W. Shaw, R. Van A. Mills, D. Dale Condit, G. B. Richardson, G. C. Matson, and C. H. Wegemann collected the samples upon which the physical determinations were made. Acknowledgment is made to my colleagues of the United States Geological Survey for many suggestions and criticisms; to Mr. Mills for the production data given of the oil wells from which some of the samples were collected; to Mr. A. W. McCoy of the Empire Gas and Fuel Co., Bartlesville, Okla., for many ideas. Determining Pore Space of Oil and Gas Sands In selecting a method for the determination of pore space, two objects were kept in mind: First, the method must not only be sufficiently

Jan 1, 1921

By R. J. Wysor

MORE than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100° F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently clone some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C. R.. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based oil the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations.

Jan 10, 1915

By Victor O. Strobel

Fire-brick hot-blast stoves have been the subject of frequent discussions at the meetings of the Institute; and although it is my object to elucidate some of the points in connection with this subject, I will not go into the specific features of all types, but more especially call attention to a new type recently designed by Mr. Fred. W. Gordon. As the economical production of a ton of pig-iron is a more essential feature than a large output, much depends, where fuel cannot be obtained cheaply, upon suitable apparatus whereby high temperatures can be maintained. Where iron-pipe stoves have been employed, the fuel-consumption reached one and a half pounds of fuel, and, when a larger output was desired, often two pounds, to the pound of iron produced. The temperature attained rarely exceeded 900' F., and that at the expense of frequent renewals of the pipes, which was not inconsiderable. The fire-brick hot-blast stoves of the past five or six years have clearly demonstrated their superiority over the old system. Of the accompanying drawings, Fig. 3 illustrates a four-pass regen-

Jan 1, 1886

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

CONTENTS PAGE UREN, LESTER C.-Increasing Production of Petroleum by Increasing Diameter of Wells. Discussed by A. Beeby Thompson 1 LAHEE, FREDERIC H.-Comparative Study of Well Logs on the Mexia Type of Structure. Discussed by W. A. I. M. van Waterschoot van -der Gracht.... 4 Increasing Production of Petroleum by Increasing Diameter of Wells Discussion of the paper of LESTER C. UREN, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1364-G, with MINING AND METAL-LURGY, October, 1924. A. BEEBY THOMPSON, London, Eng. (written discussion).-The subject discussed in this paper has long been debated by operators in European fields, where very strong views are held regarding the advisability of controlling gas pressures by shutting in wells. While unwilling to theorize on the subject of restricted flow, the writer has always been disposed to associate himself with those who hesitate to impose any obstruction to a natural transitory state that breaks up the oil-containing strata and establishes a feeder system which no subsequent events, natural or artificial, can approach in intensity. In both Russia and Roumania, where the oil is concentrated in discontinuous, disturbed, and irregular lenticles of sand varying, within short distances, in coarseness of grain, extent of impregnation and degree of cementation, it has been the practice to let the wells run wild in order to provoke disruption of strata. By encouraging violent eruptions, an extended feeder system is created and the ejection of enormous quantities of sand, rock, and clay creates a sump and seepage area that it would be difficult to imitate by any artificial means, not excluding actual mining. Before discussing the somewhat novel method suggested for enlarging the infiltration area, the writer would like to confirm the fact that many valuable data applicable to oil are forthcoming from a study of water phenomena. Long association with water-supply problems in many parts of the world has shown how closely the phenomena of underground movements of water and oil are related, so that it is pleasing to note the author's use of water formulas. But there is one great distinction;

Jan 7, 1925

Lawrence Addicks, Perth Amboy, N. J. (communication to the Secretary*): The excellent series of photo-micrographs given in this paper shows clearly the relation between micro-structure and cuprous oxide in refined copper. The authors suggest that this method of examillation might be substituted for the " button " method now used to control the refining of cop

Jan 1, 1904

By F. B. JEWETT

TWENTY FIVE years of doing, finding, and encouraging others to do scientific research in' industry, and of organizing the machinery for the` smooth 'and effective conduct of such research, have left me with a feeling that so far as this branch of human activity is concerned the problems in 'essence are- not, materially 'different from those met elsewhere. Years ago, in a less mature period of life, I may have thought that the effective industrial research man was a being somewhat different from his fellow workers in adjacent 'fields, but I have long since 'changed my views. The rank and' file of the modern industrial research organization are relatively easy to find, though some¬times difficult to get in sufficient numbers. Mistakes in choosing them are not particularly serious to the or¬ganization, however unfortunate they may be for the misplaced individual who persists too long in the wrong environment. The reason for this is obvious from the fact that, taken by and large, the work of the rank and file is at best necessarily a work of detail done under guidance of the more experienced. In this respect the situation of the rank and file in an industrial research organization is not different from that class in any other group activity, whether concerned with industry, the university, or the church. This does not mean, however, that we are not all anxious to have the best possible material obtainable in the rank and file, or that we are indifferent to the utmost of encouragement and stimulation to its individual members.

Jan 1, 1929

By Richard Kunter

INTRODUCTION Additional work has been done on the CIP circuit at Creede, and a brief description of this work is presented in this paper. DREDGE The original dredge for the Bulldog was built by Al Hack, Inc. of Denver. The dredge cutter head is mounted on a boom made of 6-inch diameter pipe which is raised and lowered by a cable-pulley system. Maximum cutting depth is 8 feet. Slurry from the dredge flows through a floating 6-inch diameter pipe supported on 55-gallon drums which runs from the dredge to the shore and then to a trash screen and pumping system. See Figures 1 and 2. The cutter head, suction pump, winches for dredge movement, and all other operations are controlled from a small operations house located toward the rear of the dredge. All of the basic dredge equipment is mounted on a chassis about 8 ft x 16 ft in size. Additional buoyancy was originally provided by sealed 55-gallon drums supported along the sides of the chassis by a small wooden framework. Additional framework and barrels on the front of the chassis on either side of the cutter boom provided additional stability, particularly when digging in hard material. The dredge was quite stable, but two problems were apparent. For one, it could have been sunk by someone from the shore firing a rifle into all of the barrels. In prime deer-hunting and sportsman country

Jan 1, 1983