Search Documents

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By G. R. Mansfield, W. B. Lang

THE third year of Government exploration for potash by the U. S. Geological Survey and the U. S. Bureau of Mines under the authorization of the act approved June 25, 1926 (Public 424-69th Cong.) is drawing to a close. The results thus far obtained are thought to be sufficiently interesting and satisfactory to justify the presentation of a brief preliminary account of the work. Review of Earlier Exploration The general geologic similarity of the Permian basin of Texas and New Mexico to the potash field of Germany had long ago suggested the possibility of the presence of potash salts somewhere in that basin, but petroleum exploration was then making little headway there and the necessary data could not be obtained. The discovery by Udden in 1912 of potash in brine from the Spur well in Dickens County, Texas, was the first direct evidence of its presence. In 1915-17 the U. S. Geological Survey drilled a test well with standard tools at Cliffside near Amarillo, but failed to find potash. Nevertheless, an observer has been kept in the field, at first in cooperation with the Texas Bureau of Economic Geology but since 1922 by the Survey alone, to secure data and samples from oil and gas tests. Since the discovery of oil in Reagan County in 1923 exploration by drilling has been rapidly extended to many parts of western Texas and southeastern New Mexico. The identification of the potash-bearing mineral polyhalite was first announced by the Geological Survey in June, 1921, the material having come from cuttings from the Bryant well in Midland County and the Burns well in Dawson County, Texas. Successive discoveries and announcements of similar purport aroused widespread interest in potash exploration, which culminated in the action by Congress already noted. Permian Salt Basin The Permian salt basin extends generally northeastward from western Texas and southeastern New Mexico through the Panhandle sections of

Jan 1, 1929

By A. G. McGregor

In the Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 1/2 in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining CO.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally 1/4in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft, from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 1/4-in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar —water, sodium silicate, and finely ground silica—was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By R. R. Brandenthaler

Petroleum producers in the Mid-Continent field, up to the present time, have been more concerned with the mechanical operation and efficiency of the gas-lift than with its possible effects on the physical properties of the oil. As a result few specific data are available on the subject and contradictory opinions exist. Some operators are positive that the gravity of the oil is decreased, while others present data which definitely show that the gravity of the oil is increased. In other localities, some operators have given careful attention to the effect of the gas-lift on the gravity of the oil. When the emulsions formed have given much trouble, the problem has usually been dodged by placing the well on the pump. Certain Fundamentals Certain fundamental results may be expected under ordinary conditions and with all types of crude oil, when gas is the prime mover of oil in producing formations. For example, the gravity of oil will decrease as the rock pressure in the producing formation declines, the change being greater in the higher gravity oils. Furthermore, the character of emulsion formed is primarily dependent on the kind of oil, thus more refractory emulsions are formed from asphaltic-base oils, less refractory from mixcd-base oils, and the least refractory from paraffin-base oils. However, refractory emulsions are sometimes formed from paraffin or mixed-base oils that are difficult to treat by ordinary methods, especially by electrolytic processes. With oils having the same base, those of lighter gravity are less subject to the formation of emulsions, especially of refractory emulsions. There are two types of emulsions formed; namely, water-in-oil emulsions and oil-in-water emulsions. The former are the more common; in fact, very few examples of oil-in-water emulsions have been noted in the oil fields. The amount of water produced with the oil influences the percentage of emulsion formed. Agitation and velocity of flow play an important part in the forming of emulsions.

Jan 1, 1928

By J. L. Bruce

' For a number of years, from an economic standpoint, the ventilation of the Colorado mine of the Davis-Daly Copper Co. has been a difficult problem. The development through the main hoisting shaft was pursued for a number of years and to a depth of about 2500 ft.(762 m.)before large bodies of good commercial ore were opened. This lack of early success in exploration restricted expenditures for ventilation, with the result that the present orebodies were developed at a depth of 2500 ft., and in country rock of relatively high temperature, without adequate means of supplying the development faces and the stopes with cool or fresh air of low humidity and suitable velocity. During the progress of development, two or three connections were made at higher levels with the workings of adjoining operations, but these were of a makeshift and unsatisfactory character and afforded no means for carrying downcast air from the surface, in anything approaching a direct course, to the working faces. During the latter part of 1917, arrangements were made with the Anaconda Copper Mining Co., whereby, during the year 1918 and the early part of the year 1919, a crosscut was driven eastwards on the 2500-ft. level of the Colorado shaft and connection was made by means of an up-raise of approximately 200 ft. to a crosscut driven westwards from the 2800-ft. level of the Belmont mine, this crosscut at the top of the raise being driven at Davis-Daly expense by the Anaconda Copper Mining Co. This connection, in conjunction with a No. 11 Sirocco fan installed near the Colorado shaft, provided the Colorado mine with a maximum of approximately 30,000 cu. ft. per min. of relatively fresh air, most of which came in a fairly direct route from the downcast Belmont shaft through the No. 11 fan to the 2500-ft. level stopes. After passing through these stopes and the stopes of overlying levels, it passed through the main crosscuts on higher levels back to the Colorado shaft, which provided the upcast for this current of air. The improvement noted on the completion of this work was marked, and, for a time, fairly satisfactory. Further extension of the mine workings, however, and

Jan 1, 1922

By S. D. Michaelson

[CONTENTS PACE See TP 2377, Min. Tech, May 1948 for discussion of A Technique for Photographing Difficult Subjects through a Petrographic Microscope (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL). Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy (TP 2141 by R. A. ....... PALLANCH, Min. Tech:, March 1947. Discussion by S. D. MICHAELSON). I Symposium on Milling Devices and Practices. (TP 2162 by J. F. MYERS and R. J. TOWER, Min. Tech., May 1947. Discussion by HARLOWE HARDINGE). ............ 2 Rod Milling-Plant and Laboratory Data. (TP 2175 by J. F. MYERS, S. D. MICHAELSON and F. C. BOND, Min. Tech., July 1947. Authors' supplement and discussion by HARLOWE .......................... HARDINGE, and B. H. IRWIN) 2 A New Separating Vessel for Sink-float Concentration. (TP 2182 by E. C. BITZER, Min. Tech., May 1947. Discussion by E. H. CRABTREE, JR.) .................. 5] Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy S. D, MICHAELSON*-The method of determining the efficacy of a separation described in this paper, gives the metallurgist a most useful guide for keeping his ship on an even keel When the ore Waves vary from placid seas to high breakers. Now that such a method of evaluating metallurgical efficiency has been developed and proven practical, it Would seem logical to introduce the next, and more final, factor of Economic Efficiency. I choose to define this term as the percentage ratio of net return from milling to the theoretical maximum net return. The actual operating cost subtracted from the actual mill return represents the net actual amount received for the material treated. Experienced operators of most plants Would ordinarily have enough data on hand to estimate a theoretical milling cost per ton, based on labor, power, supplies and maintenance When operating at maximum tonnage With minimum trouble and under ideal ore conditions. When this theoretical estimated cost is subtracted from the theoretical maximum ore return (calculated by Pallanch's method) the resulting figure is the maximum theoretical net amount the mill operator could hope to realize in processing the ore. The percentage ratio of these sums, of actual to theoretical, is the economic efficiency of the operations. This economic efficiency, if determined on the basis of a fixed market price for metal and similarly fixed base rates for labor, power and supplies, Will reflect the effect of changes in milling practice, labor efficiency and equipment condition. When computations made on the basis of actual current rates for labor, power and supplies are compared With similar actual figures for past periods they will show forcefully how energetic our hunt must be to develop man saving controls, more effective metallurgy, and better equipment to maintain profitable operations. Such computations also offer a simple means of determining how much more labor, supplies and power can be put into the mill operation to obtain an increase in metallurgical recovery at a profit.

Jan 1, 1947

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

CONTENTS DAVIS, CARL R., WILLEY, J. L., and EWING, S. E. T.-Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores. Discussed by Charles E. Locke, H. W. Hardinge, H. N. Spicer, G. M. Brown, Justice F. Grugan, R. C. Canby 1 WEINIG, A. J., and BOWEN, MAX W.-Determination of Dissolved Oxygen in Cyanide Solutions. Discussed by A. L. Blomfield, M. F. Dycus, A. W. Bull.... 4 LEPSOE, ROBERT.-Precipitation Efficiency of Zinc Dust in Cyanide Process. Discussed by G. M. Brown, Charles E. Locke 5 Recent Developments in the Fine Grinding and Treatment of Witwatersrand Ores Discussion of the paper of CARL R. DAVIS, J. L. WILLEY, S. E. T. EWING, presented at the New York Meeting, February, 1925, and issued as Paper No. 1386-B, with MINING AND METALLURGY, December, 1924. CHARLES E. LOCKE, Cambridge, Mass.-In this country, we have come to think that we should use smaller size of feed in our ball-mills. I will admit that a ball-mill is not comparable to a tube-mill, as conditions may not be the same, but there we have an unusual demonstration of the advantage of a coarser feed. Further investigation along this line is going to lead to some valuable results. The authors have overcome the difficulty of this coarse feed by taking out what I would call the difficult lumps, It is not clear from the paper whether many of these difficult lumps' may not be 'reduced portions of their grinding media. H. W. HARDINGE, New York, N. Y.-The idea is not exactly new because in 1911 they used the miner to reduce the finer material. We proceeded three or four years using many tons, about 15 tons. or nearly the same proportion of ore to grinding medium. Another thing to be taken into account is the hardness of the ore being ground. In South Africa, the transportation costs must be, taken into account. They are also making progress in the method of using tube-mills and ball-mills instead of stamps. Experiments are to be conducted with 10-ft. diameter mills there, with the object of increasing the mass action and agitation which, as has been demonstrated under different circumstances, increases the overall efficiency.

Jan 6, 1925

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.'.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955

By David J. Reddish, Barry N. Whittaker

The characteristics of surface ground strains due to longwall mining are reviewed with special reference to U.K. coal mining observations. The current empirical method of estimating ground strain is discussed. A method of determining surface ground strain above a longwall extraction is described whereby strain can be accurately represented along a line in any direction. The discussion is supported with examples of its application to common subsidence engineering problems.

Jan 1, 1984

By Harrison R. Cooper

Computer process analysis and control techniques are overcoming major hurdles to acceptance in the mineral industry. With the growing list of new advances characteristic of a rapidly maturing discipline, management of the companies on the leading edge are keenly aware of the advantages of using computer methods in process applications. Significant advancement is already evident in such technical areas as operations research, mathematical modeling, statistical methods, and computer-based procedural techniques. The early advances during the past decade are already documented in prior symposium proceedings of this series. Thus, the currently active areas of the advancing technology are emphasized here. This section deals with applications in pyrometallurgical and kiln processes. The two sections which follow deal with concentrating operations from two points of view: 1) mathematical modeling, and 2) on-line control. In the metallurgical field, emphasis on developing effective process computer applications for the steel industry began in the late 1950's. Simulation techniques also received substantial attention. The steel industry was soon joined by the cement industry in the development of computer methods for process applications. Computers were in use for feed-material blending and kiln control in the early 1960's. Computer development in other pyro processes, such as aluminum reduction and glass-making, also marked significant advances by the mid 1960's. Aluminum smelter potline control is a nearly universal application at this point, and the development of glass furnace computer process control represented a recent important technical advance in digital control techniques. Steel Hot strip rolling was the earliest significant process computer application in the metallurgical industry. Computer control of rolling mill operations is now a steel mill standard component, particularly in plants newly placed into production. 1, 2 Initial computer installations principally carried out procedural routines in setting mill clearances for production lot control. Recent developments are leading toward feedback control based on mathematical model techniques. 3

Jan 1, 1969

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By G. V. Cullen, N. G. Siviour

It has previously been reported that metal loadings of up to 6.8 m. eq/g. of dry coal can be obtained by contacting brown coal or lignite with ammoniacal solutions of ammine forming metals. Application of equilibrium expressions to further experimental results indicates that the extraction is by ion exchange, that the exchange is divalent-univalent for Zn, Cd and Ni, but is mainly univalent-univalent for Cu, and that to obtain reasonably uniform values for the equilibrium constants correction formulae must be applied to compensate for multiple functionality of the coal and its pH dependence in ion exchange. The results are shown to be consistent with the hypothesis that metal ammine complex cations are exchanged for protons derived from carboxyl and/or phenolic hydroxyl groups in the coal.

Jan 1, 1981

By N. A. Zeigler

Considerable work has been and is being done on the changes of physical properties that take place in alloys at elevated temperatures, and much information on this subject is published. Much less is known, as pointed out by Rickett and Woodll about reactions between the alloys and atmospheric gases and still less is known abut changes within the alloy itself under the influence of heat and given atmosphere. Moreover, most of the work published has been done on the alloys of "heat-resisting" type, in which chromium is an essential ingredient, the behavior of all other alloys being quite unknown, except perhaps of decarburization produced at the surface by oxidizing atmospheres. It has been shown2 that iron, with total amount of foreign ingredients not exceeding 0.01 per cent, if heated in an oxidizing atmosphere at above 900" C., may be saturated with oxygen to 0.1 per cent. It was suspected that something of a similar nature may take place in iron-silicon alloys (transformer material), the mechanism of such processes being either a direct diffusion of oxygen into the alloy, or oxygen combining with silicon to form SiO2 or more complicated (silicate) inclusions. Another possibility to be considered was that during annealing in oxidizing atmospheres, when scale is being formed, silicon may oxidize preferentially at the surface, thus impoverishing the alloy in silicon. In collaboration with Dr. T. D. YensenP3 the writer set out to investigate this problem about two years ago in order to settle these questions. Testing Procedure In the first part of the investigation, two pieces of 4 per cent silicon iron, prepared in hydrogen atmospheres and forged to 3/4-in. square bar,

Jan 1, 1934

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By F. H. McDowell

DURING the last eighteen months the Tilly Foster Iron Mine Company, the President of' which is Mr. E. I?. Hatfield and the Managing Director Mr. B. G. Clarke, has been carrying out a plan

Jan 1, 1889

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918